Search the Community

Hi, I have a CPU 314IFM order number 6ES7 314-5AE10-0AB0 when i select it in hardware config it show I/Q adress 124 -155 while it should be to 129 only (the manual mention that and it covers all inputs and outputs and the special funaction also) I try (offline) to change the order number only (another 314IFM) found it give different address range for each CPU while it all have 20 DI/16DO 4AI and 1AO

Hello all, I'm new to this forum, hope I will be able to get some answers on this forum. I'm wotking on maintanance for machines under productiona and I would like to conect one machine to my work PC. But when I try to setup conection with RSLinx, RSLinx don't see my PLC. Problem is that my PC is on network with IP addresses 192.168.8.XXX and machine is on 192.168.0.1 IP address and between is cisco RV180 routher which is set to have LAN address 192.168.8.168 (company network), and WAN is set as 192.168.0.200 (subnet 255.255.255.0, gateway 192.168.0.201, dns 192.168.0.202). When I conect directly 1756 ENBT/A card to my laptop (laptop is set to same range of IP addresses) I can see PLC and everything is working but this way is not practical for me. Is there any way to conect my office PC to PLC, some settings in RSLinx Clasic? Any idea would be helpful. I attached simplified network drawing for easyer understanding. network.pdf Thank you for your time and help, best regards, baric1007

Anyone know how to read a program of KV 40 with protection MEMSW $ 8,000. It's an old ladder diagram I want to retrieve. I've seen this link which talks Pseudo reading it. Link http://forums.mrplc.com/index.php?showtopic=6782 Thanks, Ágora

Hi All; I am struggeling to get my CITECT to talk with my CJ1MCPU12 with ETN21 module. I can ping the IP address from the citect PC and also connect CXONE using ethernet with supplied IP Address. I do not have FINSGATEAY installed as the PC is Windows 8 with CITECT 7.4. Any Ideas would be most welcome as I am drawing a blank. My settings are OMRON ETN21 IP: 192.168.0.3 Unit number: 0 Citect SCADA Primary Server IP: 192.168.0.24 Citect.INI [OMFINS] Source = 1/3/0 (not too sure what this should be...) COMMUNICATION settings: [bOARD] Name: BOARD1 Board Type: TCPIP Address: 0 [PORTS] Name: PORT1_BOARD1 Board name: BOARD1 Special Opt: -I192.168.0.3 -P9600 -U [i/O DEVICES] Name: Internal Number: 1 Address: 1/3/0/S Protocol: OMFINS3 Port Name: PORT1_BOARD1 Startup Mode: Primary Prioirity: 1 Memory: True

Hello all! I have one problem and i need an advice. I search for fast plc, that could have minimum plc cycle. I got 2 inductive sensors 0-10V (0.5 - 2mm). I connect this sensor with plc. On plc is connected shaft encoder which is 360ppr. My task is protech a stamping tool betwen stamping and if inside tool is some bad stamping pease we muss stop stamping. i control heigh of the stamping tool with inductive sensor. Right moment for measurement i get from incremental encoder. For example: I want to measure highof the tool at 90° - 180°, so when the tool if fully pressed. Now i have Unitronic plc with plc cycle cca. 2.5 mS and only one interrupt at 1.25mS and HSC interrupt at 359° (for reset at 0). But this plc is to slow for this application. Machine run at 200 rotations per munute, so i need interrupt less then 1mS (for one degree accurity). SO i need fast plc that can do those things fast. Most importanten is Analog to Digital conversion speed. Unitronics need cca 60mS for two analog conversion, this is too much. SO i need to do those things fast: 1. interrupt for hsc for set counter on 0 2. set interupt for hsc at 90° (at rising edge) (for high measurment 3. interrupt for analog input? I need fast AD conversion so that i can check for high of the tool every one degree. so which plc shuld i use?

I am trying to setup communication between an EIP21 and a AB Compactlogix processor. Setup both units with Network configurator and Logix5000. In Logix5000 I used the Generic Ethernet Module with the correct consumer and producer tags and instances. When I go online Logix can see the EIP and bring up the module information but the connection itself is in Error 16#0114 Electronic keying Error. Unfortunately cannot find a way to disable keying like possible on the Controllogix Ethernet module. Can Anyone help. An application example or some tips how to resolve it would be great. Kind Regards Rolf

I am planning on buying a new laptop computer and I need to be able to run RSLogix Micro Starter Lite and RSLinx Lite (the free download version). The release notes for RSLogix Micro Starter Lite list which operating systems are supported. Windows 8.1 is not on the list, but that is the operating system that will be on the new computer that I am looking at. Does anyone know if it will run on Win 8.1? I would sure appreciate any information I could get on this. Thanks Mark