Search the Community

Showing results for tags 'redundancy io configuration'.

  • Search By Tags

    Type tags separated by commas.

  • Search By Author

Content Type

Find results in...

Find results that...


Date Created

Last Updated

Filter by number of...

Found 37 results

  1. I need solution for master & slave configuration between 2 PLC Twido TWDLCAE40DRF. My final project is about a system for filling drink on a cup and do the packaging. the component of the project is the filling system (dropping cup, filling water, pressing the seal) and the packing (packing into a box and sealing the box). This project is using 2 PLC Twido TWDLCAE40DRF. My problem is how to configure one of them as the master and the other as the slave. I've read the manual book but it's hard to understand the instruction. if anyone can give a simplify explaination to me please reply this post or you can reach me at mail: tatangprayoga11@gmail.com  
  2. I'm using Controllogix L61 redundancy system as a slave with DCS using ethernet tcp/ip socket programming. The communication between master and slave will fail after a switchover. Kindly give solution for this. Thanks and regards, Rasu
  3. Hi, I have encountered an unexpected "PRI" LED indication of 1756-RM Series B module. When the affected redundancy module is set to primary, the status of the "PRI" LED indicator is blinking red. On the other hand, it is set to a solid red when the RM is set as secondary. I have read the manual and there are only two expected behavior for the "PRI" LED indicator, green if it is set as the primary and off if it is secondary. Does someone encountered this scenario already?   P.S. The RM does not have any minor/major faults when accessed. The status indicator indicates "PRIM" when the affected module is set as primary and "SYNC" when set as secondary. Manual switchover between controllers are done and was successful. Thanks in advance! Regards, RIValencia

  4. Mitsubishi CC link

    kumarsaurab92@gmail.com posted a topic in Mitsubishi

    Hello every one. can any one explane me maximum how many CC link card we can configure in one  QJ61BT11N module. and whwt is difference between CC link and Input/Output card

  5. Ge Fanuc LM 90 30 PCM Commnications

    Chris Iwo posted a topic in GE

    Hi ALL, Am trying to configure a PCM 301 (LM 90 30 Communication Co Processor Module) What software do I use,is it TERMF or PCOP? And where can I buy this software Thanks
  6. Hi, I'm using a 1756-l61 in a redundant chasis. The redundancy is working properly, but when I try to be online using rslogix the connection speed is too low. i did some tests, trying to removing one controller and breaking the redundancy and the speed came back to normal speed connection. some one had this problem? if yes, could help me? thanks joao 
  7. I am having trouble loading the configuration into a Micro984-230. I lost an old M84-002 PLC. I have the program. I purchased a Micro994-230 replacement. I lost my cable, so I made a new one. The only software that I have still running is Updoc 4.30b. I tested out my cable and Updoc by connecting to a 984-381. Everything worked fine online and offline. The error I get during the configuration loading is communication error 13. I have no idea what that is. Perhaps I can't do configuration loading with Updoc. I have Modsoft Lite  working but I do not think that it works with this controller. It is for MIcro and Compact controllers. I may have modsoft and taylor kicking around but I do not know if they are installable or not. I hope I can find out if my config is improper, I have used the wrong controller setup file (used Micro984), or where iI can have the config loaded for me? I also do not know if this used controller is functioning correctly.

  8. CPM1A-AD041 configuration

    Sergey Chizh posted a topic in CX-Programmer

    hello guys .. am the new guy in this forum I am having a problem with CPM1A-AD041  configuration. Please suggest what type of operands (Data Type, Address) should be defined for the selected operand (see attachment drawing). This example is taken from the module's configuration manual for CP1H CPU Unit (WA450-E1-06). CPM1A-AD041 works with CP1H-XA40DR-A. thanks in advanced :)
  9. Hi, Good day to all,   I got a situation regarding the redundancy configuration. Please refer to the image attached (Page 26, Enhanced Redundancy User Manual). Notice the 1756 ControlLogix I/O inside the green box! The chassis hasn't got a CPU but only has an Ethernet IP module for the entire chassis. Does anyone know how to add and configure this chassis to the I/O configuration tree of RSLogix5K (Logix Designer 5k)? On my configuration, I've also inserted 2 MVI56E-MNETC Modbus TCP/IP Module in addition to the standard I/O Modules. Is my configuration possible? I appreciate any help I could get, thank you very much!   Sincerely, Andrei O. Karunungan

  10. IFIX Problem

    N_Locus posted a topic in GE

    I have restored a crashed IFIX to a new PC. The restore is ok and installed GE9 driver. With the GE9 power tools, we can observed that data transmits and recieve. The problem is that the screen scada is not updating i.e. no status/feedback, anything is happening. The LAN network TCP/IP was configured i.e. IP, subnet and gateway. Any remedies/advice is most welcome. Please provide a guide on the communication/configuration setup. Thanks
  11. Has anybody used the Spectrum Controls 2080sc-IF4u analog module? This is a 4 channel analog module for the Micro800 series?  I'm trying to set input 4 to (0-5v, x10(format)2-wire, 60HZ). I need someone to help me figure out the bit setting. This is what I have LSB=44 and MSB=44 could some else confirm this? Thanks

  12. FX3G Hardware configuration

    mohamadnoureldeen posted a topic in Mitsubishi

    Dear All, I really appreciate in advance your help in this problem. This is my first project with Mitsubishi PLC. I am using GX Works 2 for programming. Hardware is FX2G-24M base unit + FX2n-16EX extension module. I already started a new program and download simple rung on PLC, put PLC in run mode, test it and working properly. the problem is that I do not know what is the address of inputs of extension module. I tried to complete and use X016 but no response in PLC. kindly advise what shall I do. Thanks