Search the Community

Showing results for tags 'qd75ms module mr-j3-b program with functional block sample'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Found 158 results

  1. I have an Omron NX PLC  NX1p2 which Supports EtherCAT . also I have Balluff BNI00HA Ecat Block(IOlink Master). I have setup communications and connected a BNI004K balluff I/O device. I managed to get inputs and i can read it as well. but to set the pins of BNI004K as outputs i have to configure the module by accessing its Index and Subindex. I tried with IOLwrite Block but it says 16#4802 error. Also an Engineer from balluff suggested me to use CoE block but while reading the description is said CAN over EThercat. WHile my devices are IOLINK.. If Anyone can Help.Please. SS1 - Is the error I am getting on IOLink instruction SS2 - Is what i did. which is an IOlink Write block from Omron SS3 - is what balluff Engineer suggested.
  2. Problem: I am getting a control sync fault on 2 recently installed kinetix 5500 but only when my programing PC is connected to the machine network.  Install and setup all went great over a 5 day period.  Then all of a sudden I started to get this fault. Sometimes 100 times in an hour.  As soon as I go offline, and unplug my PC the problem goes away.  I have also tried another PC connected to the Machine network and still get the same result.  Sometimes machine can run for hours with my PC connected with no problem.  I do not have to be online with controller for fault to occur. Setup: I have the 2 K5500's ethernet ports daisy chained together, and then connected via shielded CAT 6 cable directly to port 2 of the Compact Logix Controller Coarse Update is set to 3.5ms and utilization's are at 33% and below.(I have tried the default 2ms with same results) Ethernet modules are configured with FW rev 7.013. Machine network is isolated.(not connected to plant network or internet) Equipment: Compact logix L33ERM Running version 30.01. There are a total of four servos in this system all running over ethernet.  2 Kinetix 350's(not affected), and 2 kinetix 5500's. I have tried: separate ethernet cables for each drive ran through a switch different ethernet cables resetting coarse update speed connecting a different PC for programming   I am just not sure where else to go with this.  Thanks in advance for any help.  
  3. Hi all , I have been using MELSEC - Q series plc for the past two project i dont find any issue with that but for the third project  used same PLC same model but there is issue which I found unable to resolve  The issue is when i try to communicate PLC using LAN cable by direct ethernet connection it works normally but by communicating using HUB network I cannot communicate, I checked all the parameters setting, I dont know what is the issue even contacted mitshubshi service to troubleshoot but they are not responding  So here i am for your guidence to solve this issue   see the images below to analyse this issue This connection is direct ethernet connection which works normally    The parameters are set and writed to PLC The IP is set to my PC for communication  When i try to find the cpu in the network it shows the cpu IP  After that I checked for connection Test it show error I have also attached the Network route which i used to communicate  Network Drawing.pdf I hope someone will help me to solve this issue Thank you , madhan ravichandran
  4. We are getting a processor watchdog fault on a kinetix 5500 but I cant seem to find any information on the cause of this particular issue.  Has anyone ever seen this before? Thanks guys
  5. Hi all, I would like to know how to communicate scale indicator device mettler Toledo ind 320 using  module QJ71C24N-R4 by predefined protocal   I also tired to communicate in CH1 with the G.INPUT instruction to communicate when the device in MT continue mode it does communicate but I dont know how to convert value Now by trying modbus communication predefined protocal works fine but i cannot read data the is no SD/RD transmission happening  Can anyone help me with this  Thank you serial monitor.gxw serial monitor.gxw
  6. QD77MS4

    Hi My system : plc Q03ud , simple motion module : QD77MS4 , software : Gx works2 , Application : rotary table and unit degree I send position and speed from HMI ( got 2000 ) , my problem is that when i want send 90 degree for position ( dmov d0 u0\g2006 ) , i have to enter the 9000000 from hmi . and for speed i have similar problem Position hmi ( 9000000 ) ===>> motor rotate 90 degree  Speed hmi (100000) ==>> motor rotate with 100 degree per min
  7. Hello, In GX Works2, what do asterisks before function block input and output variable names mean? Thanks,    
  8. Hi, Does anyone know where to get EDS files for GX Works3 ?  I can't open a file that I need to access because it has an "Unsupported Module". The module is 007ER-1FL2-T, it shows up on the Mitsubishi website but I cannot see any links to EDS files or any software related to this module. Cheers, Olly  
  9. Crouzet Millenium 3

    Recently had to get a program out of a millenium 3 plc which I had programmed a few years ago but the cable would not connect.The only difference this time ,as my laptop no longer had a rs232 port,was the use of a USB to rs232 converter. Having trawled the web I managed to find the circuit of the interface cable below. It looks like the signal from the computer uses the negative going part of the pulses which aren't present on most usb to rs232 converters. Is this correct?
  10. Hello, Good Day All. I am facing this issue while I am going to copy old plc to new plc. but old plc having 4965 steps, once going execute this program to new plc its showing more than 8000 steps. please suggest on this. PFA.
  11. I have a 1747-L30B SLC Brick and it is set to load from EEPROM on boot S:5/8, Error S:1/10, and Run S:1/12. I need to make changes to the program and then store it to EEPROM via "Comms>EEPROM>Store to EEPROM."  When I attempt to store the program with changes, it displays the message "Insufficient Memory Module Size." I assumed the EEPROM memory was maxed out, but I also uploaded the existing program currently stored to EEPROM, made no changes, and attempted storing it back to EEPROM and received the same message. Any advice?
  12. Version 1.0.0

    40 downloads

    PRNG algorithm packed into a functional block. As an example of using ST language for Omron CJ series PLC.
  13. Function block RANDOMIZE on ST View File PRNG algorithm packed into a functional block. As an example of using ST language for Omron CJ series PLC. Submitter drYurban Submitted 10/05/22 Category PLC Sample Code
  14. Version 1.0.0

    29 downloads

    An example on ST is the definition of the fronts of a discrete signal.
  15. Function block on ST for algorithm DIFU DIFD View File An example on ST is the definition of the fronts of a discrete signal. Submitter drYurban Submitted 10/05/22 Category PLC Sample Code
  16. valve_control

    Version 1.0.0

    49 downloads

    A working example of an FB to control a valve from an HMI panel. Controls closing/opening times, plus a little visualization.
  17. valve_control View File A working example of an FB to control a valve from an HMI panel. Controls closing/opening times, plus a little visualization. Submitter drYurban Submitted 10/05/22 Category PLC Sample Code
  18.   Hello, I downloaded the program from the M251 PLC program, using the SoMachine4.3 environment. However, the downloaded program does not compile because the library is missing. The library is from a different manufacturer. Is it possible to find this library on the M251 PLC device? is there any way?
  19. Anyone you know any books,software or educational package to learn plc program at home Please??  
  20. Mitsubishi Fx2n Modbus rtu vfd

    Hello everyone, may you all bless with the best. Can anyone please help me on connecting and programming In Modbus rtu INVT CHF-100A vfd with FX2n having rs485-bd module. I want to connect 11 vfd and one fx2n plc also .
  21. Mitsubishi Fx2n Modbus rtu vfd

    Hello everyone, may you all bless with the best. Can anyone please help me on connecting and programming In Modbus rtu INVT CHF-100A vfd with FX2n having rs485-bd module. I want to connect 11 vfd and one fx2n plc also 
  22. Hello everyone,  I have a Panelview plus 600 ( I know it’s old but I’m trying to get it to work). It’s on a yogurt bucket filler, I don't have any application to run or to do anything. What software do I need on a computer to be able to transfer it to the panelview. Is this even possible?  There is nothing in the memory right now but how to I program it and what program do I use?  I’m in the Los Angeles area and even willing to pay for someone to come and do it.  I need to get this to work, thank you so much. 
  23. Hi, I have quite a noobie question. I want to create a function block to do some simple operations on 2 variables. Both variables are In/Outs (see picture attached). How can I make this function accept variables regardless of the data type? Given these is just simple math I am able to use the same instructions in REAL, INT, UINT, etc. But, the function block only lets me assign one Data Type to the In/Out variables.
  24. MITSUBISHI A1S68AD PROGRAM

    HELLO EVERYONE I am having problem writing in A1S68AD program, please help me out. My system configuration is as :- 1. A1S POWER SUPPLY   2. A2SHCPU   3. A1SJ71AT21B    4. A1S68AD  5. A1S62DA  6. A1SX81-S2 7.  A1SX81-S2  8. A1SX81-S2  9. A1SY10  10. A1SY10  11. A1SY10  12. A1SX80-S2  13. A1SX80-S2 14. A1SY10  This is my existing configuration. But now there is one more slot empty and now i want to add one A1S68AD CARD in the empty slot, i tried writing the program for this card, but plc gives me error. SO, anyone can send me the program with addresses for this card. It will be very helpful as I am new to this A series Mitsubishi PLC. AND HERE BELOW IS THE ATTACHED EXISTING PLC PROGRAM AND SYSTEM IMAGES. PLC PROGRAM.zip
  25. Good day everybody,    Currently I am working on an application using 3-axis controlled by a QD77MS4 Simple Motion Module.  In this case, I have already set up most of the configuration, but when I try to execute the program, I get the following error:   SP. UNIT ERROR - The location designated by the FROM/TO instruction set is not the intelligent function module/special function module.  - The module that does not include buffer memory has been specified by the FROM/TO instruction.  - The intelligent function module/special function module, Network module being accessed is faulty.  - Station not loaded was specified using the instruction whose target was the CPU share memory.   The QD77MS4 Module is mounted in Base Slot #3, so I use U2\G800, U2\G1500, etc... to Read/Write from it.  The Diagnostics tool indicates the error occurs as soon as I try to access the U2\G800 Buffer Memory. If I set this part of the program to No Execution the error is no longer displayed.  Additionally, if I try to monito the Buffer Memory area of the Module, it says that "The Module Stat Address is incorrect".   I already tried changing the position of the module in the base (Slot 3 --> Slot 1) and changing the corresponding values to reflect that, but still the problem persists.    What am I doing wrong? Is there some kind of configuration I could be missing?    Thanks in advance for your help!