Search the Community
Showing results for tags 'problem with communications'.
Found 58 results
-
Hello everybody, I have a problem connecting CS1G-H CPU42 with CS1W-PRM21. Prm21 is inserted in slot 9, and i have previously made connection to prm21. After downloading configuration to prm21 i cant connect to prm21 anymore (connection to plc is working fine). The cx-configurator says CS1W-PRM21 PROFIBUS DP-V1 Master Communication Failure with UnitERH is on (red), BF is flashing red, RUN is on (green), PRM is on (green) and BST is flashing green. How can i restore comunication with the cs1w-prm21 to diagnose the problem? After some examination the problem is (probably) that i have configured prm21 to write in the adresses of CIO3000 to CIO3400. That is interfiering with other address. Is there any way to force the output of the prm21 off, or make device go in offline mode.At the power on of the prm21, i can test the connection via cx-configurator and is working and after 2 seconds the prm21 goes to stop mode and begin writing to address of the sysmac bus area. I am thinking if i can stop prm21 from writing to that area i will be able to connect and load default configuration.is that any way to stop the prm21 from automatic start? or is there a way to reset prm21 to factory settings? best regards
- 3 replies
-
- CS1G-H CPU42
- CS1W-PRM21
-
(and 1 more)
Tagged with:
-
PowerFlex 525 overwrite my parameters/ Spd + Strt Problem
charonsk posted a topic in Allen Bradley / Rockwell Automation
Good day, I´m helping with small project and currently i am stuck because of this problem. And I hope you can help me out. I´m using PowerFlex 525 connected with AB CompactLogix 1769-33ER PLC via EtherNet/IP. Connection is working, I can read and write values from/to 525. To configure both devices i´m using RSLogix 5000. 1) First problem occurs after I loaded configuration to 525 and it´s, that 525 keeps overwriting values of Accel and Decel Time 1. It happens when i directly change parameters in Module Properties (online) or after I upload configuration to device. It happens even if i set parameters directly to 525 with its HMI panel. - I kinda get around this problem when i use Accel/Decel Time 2 for Step logic, but if i send direct reference value motor still jump to it and that is not good, especially when changing direction of rotation. 2) Second problem is that I cant get Speed Sources and Start References right. Usually Is working only option 1 and others are not, or they are doing something else that they should. For better imagination this is what i want to do: I have 3-state switch (left = 1 ON(DigIn TrmBlk 02), 2 OFF; center = 1 OFF, 2 OFF; right = 1 OFF, 2 ON(DigIn TrmBlk 03)), In center position I want to control 525 with EtherNet (already working when: Start 1 AND Speed 1 = EtherNet/IP). In left position I want to control motor directly with Drive Pot and In left position a want to start Step Logic (which i have already set) - Funny thing, If I set Start 1 = Ethernet, Speed 1 = Step, Start 2,3 = DigIn, Speed 2,3 = Drive Pot then in all three position motor goes in Step logic.. Or when i get left and right position working then Ethernet is blocked.. and this kind of things.. I Attach print-screen of my current settings, if you need something more just, tell me. Thank you for your time, and I hope someone will be able to help me.- 1 reply
-
- powerflex 525
- problem
- (and 5 more)
-
Hi guys, I have a problem with GX IEC Developer 7.04, i hope some of you can help me. When i try to connect with the PLC type - Melsec FX1s- 30MR-DC, there is an error: I check all COM port settings, and everything is ok. Com_port parameters: FX Parameters: Transfer setup: PLC Type in the program is the same like physical one (FX1s). I try to change all of this stuffs but there is no result. The cable I use for comunnication is this type: Thank you very much in advance. Have a nice day! eng R. Bukov
-
Hi, I have a CPU 314IFM order number 6ES7 314-5AE10-0AB0 when i select it in hardware config it show I/Q adress 124 -155 while it should be to 129 only (the manual mention that and it covers all inputs and outputs and the special funaction also) I try (offline) to change the order number only (another 314IFM) found it give different address range for each CPU while it all have 20 DI/16DO 4AI and 1AO
-
How to conect RSLogix5000 to 1756 PLC via network
baric1007 posted a topic in Allen Bradley / Rockwell Automation
Hello all, I'm new to this forum, hope I will be able to get some answers on this forum. I'm wotking on maintanance for machines under productiona and I would like to conect one machine to my work PC. But when I try to setup conection with RSLinx, RSLinx don't see my PLC. Problem is that my PC is on network with IP addresses 192.168.8.XXX and machine is on 192.168.0.1 IP address and between is cisco RV180 routher which is set to have LAN address 192.168.8.168 (company network), and WAN is set as 192.168.0.200 (subnet 255.255.255.0, gateway 192.168.0.201, dns 192.168.0.202). When I conect directly 1756 ENBT/A card to my laptop (laptop is set to same range of IP addresses) I can see PLC and everything is working but this way is not practical for me. Is there any way to conect my office PC to PLC, some settings in RSLinx Clasic? Any idea would be helpful. I attached simplified network drawing for easyer understanding. network.pdf Thank you for your time and help, best regards, baric1007- 2 replies
-
- RSlogix5000
- connection
-
(and 2 more)
Tagged with:
-
Anyone know how to read a program of KV 40 with protection MEMSW $ 8,000. It's an old ladder diagram I want to retrieve. I've seen this link which talks Pseudo reading it. Link http://forums.mrplc.com/index.php?showtopic=6782 Thanks, Ágora
-
I am trying to setup communication between an EIP21 and a AB Compactlogix processor. Setup both units with Network configurator and Logix5000. In Logix5000 I used the Generic Ethernet Module with the correct consumer and producer tags and instances. When I go online Logix can see the EIP and bring up the module information but the connection itself is in Error 16#0114 Electronic keying Error. Unfortunately cannot find a way to disable keying like possible on the Controllogix Ethernet module. Can Anyone help. An application example or some tips how to resolve it would be great. Kind Regards Rolf
-
I have GT Designer2 installed on a Win XP virtual machine. I have used the USB to serial Comm port to to upload PLC software from a FX3g plc and this works fine. My problem is trying to upload software from a GOT1000 series OIT using the same UBS-serial comm port/cable. I get the folowing error: (see attached capture) What am I doing wrong? The only thing different is that I am running Gx Developer 8.103H in my Win 7 64 bit system and that talks to the PLC fine. I am unable to get GT designer 2 to talk to the GOT1000 in Virtual XP mode. Any suggestions is greatly appreciated.