Search the Community

Showing results for tags 'nj501 ip address'.

  • Search By Tags

    Type tags separated by commas.

  • Search By Author

Content Type

Find results in...

Find results that...


Date Created

Last Updated

Filter by number of...

Found 40 results

  1. PILZ PSS AI IP address configuration

    volker81k posted a topic in Other PLCs

    Hi all, I am working on a safety PLC conversion project, for which I need to identify the input word address configured on a PSS AI IP card. The manual from the official website shows the address configuration via a DOS tool. I do have PSS SW PG WIN 4.9, but the project file has been created with PSS WinPro 2.3. Within this software there is only the option to configure how the input channel behaves, not which input word is used (see attached screen grab). Anyone with a distant memory if the addresses can be set with PSS WinPro?  
  2. Hi I need to get data from a modbus rtu device to Omron PLC NJ501. I am using SCU32 or SCU42 as serial gateway. I have tried using sendcmd function, but I am having problrm with the DstNetAdr Here's my setup Cpu NJ501 1400 ID262 OD263 AD041 V1 EIP21 SCU32 My sendcmd parameter DstNetAdr.NetNo:=USINT#0 DstNetAdr.NodeNo:=USINT#4 DstNetAdr.UnitNo:=BYTE#16#84 senddata array 02 03 00 6A 00 02 E4 24 Anyone has any idea on how to do it?
  3. View File NJ/NX Get IP Address A Library containing a function Block that can be run on any Omron NJ or NX PLC. The Function Block will retrieve the host PLC's IP address, Subnet Mask, Gateway, and MAC Address. The Port Details are presented through 2 structures , 1 per-port. In the event the PLC only has one port the structure for Port 2 will be blank. Submitter photovoltaic Submitted 12/12/22 Category PLC Sample Code

  4. NJ/NX Get IP Address

    photovoltaic posted a file in PLC Sample Code

    Version 1.0.0

    76 downloads

    A Library containing a function Block that can be run on any Omron NJ or NX PLC. The Function Block will retrieve the host PLC's IP address, Subnet Mask, Gateway, and MAC Address. The Port Details are displayed through 2 structures , 1 per-port. In the event you only have 1 Ethernet port then the structure for the 2nd port will contain all 0s. Data Format: IP Address - USINT[4] Subnet - USINT[4] Gateway - USINT[4] MAC - BYTE[6]  (hex value) Access the retrieved details by the typical parent-child tag structure. ex. Port_1_Detals.IP_Address[0] will get the first octet of Port 1's IP. Tested on: NX1P2, NX102, NX502, NX7, and NJ301 IMPORTANT: This Function Block should not be run immediately after startup. Allow the PLC a few seconds to establish a connection with the Ethernet network.
  5. Is there an efficient tool to manage and validate CX-Programmer addressing. Requirements: - Highlight Duplicate Address allocation - Compact/Defrag address range to avoid wasting memory space. Note: - Any FINS addressing will have to be reconfigured - This approach assumes symbol use rather than direct addressing in the logic.
  6. It will de nice to have an option for getting a cross-reference report for the AT address used on programs , as is now its easy to make mistakes double setting the same AT address on a program , specially this days that supplies of NA screens are not always availiable and using memory address is necessary for NB screens and SCADA communication and is difficult to keep track of the used address on a program , some times in global or in internals, right now its easy to make a mistake and use the same address twice , and this wont be detected on the compiling
  7. Hi All,Cx-Supervisor, NJ501-1340, Sysmac Gateway.I have been writing an update for a project and converting to this new controller.It's a pretty big project.Using a combination of Ladder and ST.Using Cx-Supervisor 3.5.I created some new Variables in Studio and made them Publish only.Started to create Points in Supervisor and made them I/O connected to the variables in Studio. No problems everything was connecting and working just fine.Then one of the points would not update. I could change it in the PLC and it would not change On the HMI.I deleted it and recreated it and it did the same thing. (sometimes points in Supervisor just stop working and recreating them fixes it).I then copied the control and pasted the old point into it and it did the same. Then other started to fail. Showing no reaction.I stopped the gateway and restarted, no help, I rebuilt the HMI, nope.The can check the tags in Sysmac gateway and they always change when the PLC changes but not the HMI.I checked the point maintenance in Supervisor and it would not change.I dumped all the affected variable in the PLC and in the HMI and recreated them. Then it got stranger.I could change some on the HMI and it would show in the PLC but not the other way.This is on Bools and UINTS.Stopped CX-server, tried using it with Win8 compatibility. nope.Pulling my hair out now. I should be coding but I'm trying to get the apps to work.Any ideas will be used with thanks.Peter
  8.   Mail me for Help if anyone is stuck during coding and settings.
  9. Hi I'm trying to set up Modbus RTU communication between FX3U PLC and a weigh module. I would use the ADPRW command using 0X03 to read the 16 bit Holding Register but in the weigh module the Data Address/Holding Register of the value I want to get is 400047 - 400048. How to translate the value in 16 bit?   Thanks, Fabio

  10. Omron NJ501 - IFM IO-Link - Wenglor U1KT001

    andrei.apopei posted a topic in Omron

    Hi, I am looking at reading an ultrasonic sensor value through IO-Link, using a Omron NJ501-1320 PLC connected through EtherCat to a IFM AL1332 master with a Wenglor U1KT001 Ultrasonic sensor. I have managed to read the 2 outputs of the sensor using this: Output_1 := TestABit(USINT_TO_BYTE(TxPDO_input_byte_1_6000_02),USINT#0); Output_2 := TestABit(USINT_TO_BYTE(TxPDO_input_byte_1_6000_02),USINT#1); But cannot read the ultrasonic sensor distance value, this is what page 2 in the manual says: Measured Value in 1/10 mm 2…15 14 Bit 300…4500 Octet 1 Subindex 3 (LSB) 2 1 Bit Offset 7 6 5 4 3 2 1 0 I tried a couple of conversions but couldn`t get the distance reading. Any ideas? Help appreciated.
  11. I am trying to find the proper way to tie my 1S Servo Controller STO to my NX Safety CPU via Safety Output Module.....  I am looking in manuals that I have and searching OMRON site as well.. I am unfamiliar with Omron Programming in general but have had years of AB programming.....so I figure it will be similar, but I cannot get my Drives out of ST mode.... Thanks,
  12. Hello everyone, I have a problem with packing machine. There are some issues with one of the axis, when axis actual position is near to 1800000 some error appear and operator has to turn off machine on main contactor. This axis is working in Linear mode. I think that rotary mode would be better for this axis. And here is my question. Which instructions, and what options i should change/check when i change count mode in axis's options. Can any1 point me some manuals to read or give me some advice ? Thank you in advance.  
  13. I am trying to get produced and consumed tags set up between 2 1756 racks with different ip's. The 1st rack has an ip address 172.28.6.3. The 2nd rack has an ip address of 10.81.105.8. Would this be as simple as adding an EN2T card to one of the racks and setting the ip of one onto the same network? Or is there a better way to do this?

  14. CCLink

    ConnyD posted a topic in Mitsubishi

    Hi guys, I've just completed pre-commissioning on a Mitsubishi project which uses CCLink. My remit was to get the CCLink network up and running which I eventually did but not without issues. Basically, my problem was to do with the number of bits and registers consumed by a station. I read in a manual that each station consumes 32 bits and 4 registers for read and 32 bits and 4 registers for write. On my network I had 3 ST1H-BT modules occupying 2 stations each and 3 non Mitsubishi devices occupying 4 stations apiece. My RWr address starts at W300 and RWw at W500. Like I said everything matched up and I/O checks completed successfully. My question is, and I've trawled through the manuals looking for an answer, how is the number of points calculate? For example my non-Mitsubishi devices they occupy 4 stations, Expanded Cyclic Setting is Octuple and the number of points is 896. How is the 896 calculated? Thanks in advance
  15. Good Evening, using the Ethernet Built-in LAN I need to program 4 power supply. I'm tryng to program the firstone but even if I can send the correct command to the power supply I always recive a 2006 error on SKTTCPRCP function Is there someone that can help me in order to not receive the 2006 error code? Have I to respect a procedure? It seems that at the second connection time the socket remain closed. Thank you!
  16. Hi everyone My system consists of 2 main stations with 2 CPU Q06UDEH and connected together by QJ71GP21S-SX module but I don't know how to link the address between these 2 CPU together? so can anyone help me? Thanks so much   
  17. We have an iQ-r R08cpu that will not display some labels or addresses.  The PLC and the machine it controls run as expected.  However, when we read from the PLC, some of the labels and addresses are not shown.  Although it runs as expected, we are hesitant to make any changes or write to the PLC. There is a screenshot attached.  Any advice or solutions for this?
  18. Hi folks, I'm trying to communicate with an old CompactLogix L35E via Ethernet. I have already establish communication via DF1 Serial port and was able to go online but I Do not know the IP address to communicate via Ethernet. Can someone please tell me how I could determine the IP Address or create a new one ? This Controller was remove from a working machine. Any help will be highly appreciated. Thanks, Anthony.  

  19. I/O assignment setting in GX-WORK2

    diraemon posted a topic in Mitsubishi

    hallo all, I want to ask if I click "read PLC Data" the "points" will appear, I use the QY18A output module that uses 8 points but there is no choice, the smallest is only 16 points.  so I can't put 148 in the "start XY" column ... will it affect the I / O address in the program?
  20. Lets say i have a PLC, with a name PLC1 with IP/Subnet of 10.125.34.243/255.255.255.0 I have to communicate this PLC1 with 2 other PLC's, PLC2 and PLC3 PLC2 with IP/Subnet of 10.125.34.10/255.255.0.0 PLC3 with IP/Subnet of 10.125.46.10/255.255.0.0 I imagine that, all these three are in different subnets, and so there should be no communication at all, but when i tested it, PLC1 to talking to/from PLC2 and not PLC3.  anyone know the answer to this ? How does it talk to PLC2 with different subnet, but not PLC3 which is in different subnet as well. 
  21. Please assist me with the following; regarding the ME96SSHA-MB Power meter data transition with Melsec-Q series PLC; We acquire to read various values on dedicated Modbus storage address registers at the simultaneous into a Melsec-Q series PLC via Modbus (TCP or RTU)  for calculation purposes. Naturally, since the reading of these variables are to provide accurate instantaneous results, it is a requirement that these values are to be read at one scan.   However, as can be seen below, there is a gap in address register range – of which, if all of these are scanned simultaneously, yields an exception error when read. This error is only avoided by scanning these data sets separately – which is not ideal for our application – since accuracy in calculations is imperative.
  22. Please assist me with the following; regarding the ME96SSHA-MB Power meter data transition with Melsec-Q series PLC; We acquire to read various values on dedicated Modbus storage address registers at the simultaneous into a Melsec-Q series PLC via Modbus (TCP or RTU)  for calculation purposes. Naturally, since the reading of these variables are to provide accurate instantaneous results, it is a requirement that these values are to be read at one scan.   However, as can be seen below, there is a gap in address register range – of which, if all of these are scanned simultaneously, yields an exception error when read. This error is only avoided by scanning these data sets separately – which is not ideal for our application – since accuracy in calculations is imperative.

  23. 1S Servo Merge Move

    dipen_95 posted a topic in NJ Series / Sysmac Studio

    Hi, I am trying to do a merge move on 1S Servo. The condition are as follows: Task: Move 2 in(absolute value) and then Move back to 1 in (absolute value). I have to do this move 10 times in a row.  The application is material leveling after dumping in the mold. The only question i have is if I use just MC_MoveAbsolute command, the only buffer mode for transition available is velocity. Is there a way i can do it with position. I dont want to stop when I can go from 1 to 2 and 2 to 1 again and again. Its time consuming. But rather a nice oscillation motion without stopping to mimic leveling. Can anybody please help me out with this problem.   Thanks

  24. CX-Supervisor 3.4.1

    banker posted a topic in CX-Supervisor

    Hi After updating CXS to ver. 3.4.1 I can't see point address I can see them when I editing but in the list form only the array len. is shown. When I enter a new point I can see the address. Anybody now hove to solve that ? Banker
  25. I currently have certain amount of Recipe data located in form of Excel file on to a PC with static IP address. Is there a way to get that data inside the Nj501 without using an SQL server as I currently have NJ501-1300 which doesn't support SQL. I am okay to send data to the SD card I currently have on NJ PLC as it is easy to get data from SD card to the NJ501.  If there is any example code or a link that helps me create i would be helpful. Thanks in advance. FYI: I am currently using NB10 HMI with NJ PLC.