Search the Community

Showing results for tags 'motion; servo; kinetix'.

  • Search By Tags

    Type tags separated by commas.

  • Search By Author

Content Type

Find results in...

Find results that...


Date Created

Last Updated

Filter by number of...

Found 166 results

  1. Hey y'all- I have an application that uses an Allen Bradley servo with a brake and a linear actuator to lift a plate vertically. While maintaining a position, the servo drive (Kinetix 5500) will occasionally fault due to over-torque.  I'm thinking it could possibly be due to mechanical issues i.e. bearings in the actuator but my initial thought would be that it would fault while moving up/down as well, so far I've only ever seen it fault while holding a position. This leads me to suspect that there may be something off in the control loop. I'm not involved in the setup but I know we use load observer and I reckon we use auto-tune. Other than that, I wonder if it's something to do with the brake. I also read about mechanical resonance in the manual which seems like a stretch but it could be contributing, the frame that the actuator/motor is attached to does vibrate a fair bit.  I'm familiar enough with basic motion control using Allen-Bradley and understand the basic concepts behind the servo/control loop. However I'm at a loss for why the servo/drive would spontaneously over-torque while maintaining a position.  How would you guys approach troubleshooting this further/solving this issue?  Many thanks!

  2. Problem during tuning

    Gman1 posted a topic in Mitsubishi

    Hi! I would like to do some tuning on our machine, but the problem is that the machine stops and drops origin positions. I selected User Command method with Basic setting. After 5sec I started the tuning, the machine stops with the roblem of that axis. Is there a parameter bit that goes high (or low) during tuning? There're no strange sounds nor movements..even the amplifier doesn't give error code. Is there something else that i should check? In the Servo-Adjustments parameters, One Touch Tuning setting I found the Permissible Overshoot Amount Level is set to 0.  Can it be the problem? 
  3. Hi there I was reading this thread: And trying to create 3 axes. 1 virtual axis and 2 real axis, I would like to use MC_GearIn for each real axes so both real ones follow  the virtual axis (so both can move in sync motion). But my question is: If I give Move cmd(Absolute or relative)to master virtual axis and since it's virtual, it is not going to move then how can the other real ones follow the master(assuming that it's literally electronic gearing).  Any help will be appreciated!
  4. Anyone know what could be missing to be able to import this stepper motor to sysmac? This is one of the supplied xml files for the stepper motor.     FASTECH_Ezi-SERVO2_EtherCAT - OMRON.xml
  5. Hi there This attached pic I got from Omron motion control manual. I am trying to wrap my head around it. Does it mean that the slave servo axis is gonna follow master encoder axis using GearIn FB?? If so, then Can we executive Move FB on encoder axis? Looking forward to your responses.  

  6. Axis Permanent Control

    Levent1970 posted a topic in Mitsubishi

    Hi Guys, How can I bring an axis into permanent control? that as soon as a value changes, the axis reacts. My Hardware FX5U, FX5SSC MR-JE-20B. Thanks a lot.

  7. Servo tuning

    Gman1 posted a topic in Mitsubishi

    Hi.  I am planning to do a full scale servo tuning on our producting machine. Is it possible to do it while the servos are in, assambled? I mean no production, no disassembling, servos stay where they are, just tuning them one by one with their empty load..
  8. HELLO EVERYONE THERE IS THIS PROJECT WHERE I CHANGED THE OLD SERVO SETUP WITH NEW SERVO DRIVE MRJ4200A-RJ SERIES. OLD SERVO HAS A REVOLUTION OF 15 BITS BUT NEW SERVO HAS 22 BITS RESOLUTION. PROGRAMMING IS SAME BUT MY DISTANCE CALCULATION IS DIFFERENT NOW AND MACHINE DOES NOT GIVE CORRECT DISTANCE. PLEASE HELP ME

  9. servo training

    rurka posted a topic in Mitsubishi

    Hello . Does anyone from the forum have such a program as on flimik, and he could share a program for f3x and the got1000 panel regards
  10. Good day everybody,    Currently I am working on an application using 3-axis controlled by a QD77MS4 Simple Motion Module.  In this case, I have already set up most of the configuration, but when I try to execute the program, I get the following error:   SP. UNIT ERROR - The location designated by the FROM/TO instruction set is not the intelligent function module/special function module.  - The module that does not include buffer memory has been specified by the FROM/TO instruction.  - The intelligent function module/special function module, Network module being accessed is faulty.  - Station not loaded was specified using the instruction whose target was the CPU share memory.   The QD77MS4 Module is mounted in Base Slot #3, so I use U2\G800, U2\G1500, etc... to Read/Write from it.  The Diagnostics tool indicates the error occurs as soon as I try to access the U2\G800 Buffer Memory. If I set this part of the program to No Execution the error is no longer displayed.  Additionally, if I try to monito the Buffer Memory area of the Module, it says that "The Module Stat Address is incorrect".   I already tried changing the position of the module in the base (Slot 3 --> Slot 1) and changing the corresponding values to reflect that, but still the problem persists.    What am I doing wrong? Is there some kind of configuration I could be missing?    Thanks in advance for your help!   
  11. Hi everyone, To explain the problem a little bit: I have 2 systems that are equal, they have 1 PLC, 1 Inverter and 1 Servo Axis (Image01). The devices are connected via EtherCat. The thing here is tht in these systems the PLC and Servo Axis is the same but the inverter is different. My goal is to have the same project on both systems and depending on the inverter detected use the correct program. What worked: If I add the 2 Inverters and 2 Servo Axis on the project on different nodes (Image02), I can detect which is present using the variable _EC_EntrySlavTb[n]. My issue is that if I want to make more replicas of the systems using different inverters I will eventually hit the Axis Number limit for the PLC while in reality I am only using on Servo Axis at a time. What I wanted: I would like to be able to control 1 Servo Axis with 2 different inverters (only one active per PLC) (Image03). What I tried: The axis parameters can be set using a variable of the type _sAXIS_PARAM, however it seems that the option to change the axis basic settings is not available (Manual: NJ/NX-series Motion Control Instructions Reference Manual (W508) page 5-58) (Image04). The axis basic settings is where the definition of the output device plus control words are set (Image05). Is there a work around to solve this issue? I would really like to avoid having to manually change the output device for the Servo Axis every time I make an update on all the systems.   Best Regards, BR  
  12. Hi there I am working on a project where Omron servo drags a part to a certain position using belt mechanism, But to avoid any slippage we decided to put an external encoder directly on the part. I was wondering what is the best to approach to drive the servo using the position of this external encoder. Is there any way that it can be configured directly with the servo? I am fairly new to coordinated motions, any help will be appreciated. Thanks
  13. I'm sure many of you are in the same boat with supply issues and elongating lead times with the Logix 5500 and 5700 servo drives. Are there any decent alternatives that are easily integrated into a 5380 controlled system, maybe with an AOI? I've looked at Beckoff and Parker systems, but Parker only seem to line CoDeSys as far as I can tell. Do any of you clever clogs have any suggestions for a well stocked alternative? As a side note, I'm not new to PLC programming, but I am only 6 months in to using motion and servo systems so be kind :)
  14. Hello! I'm trying to connect my QD75M2 with a MR-J2S40B1 Servo amplifier with an SSCNET cable. The problem is when I try to turn on the Servo ON/OFF on the Intelligent function in GxWorks2, an error occurs saying the servo amplifier is disconnected with my QD75M2. I'm confident that I've wired it properly. What could be the problem? Hoping you might help. Thank you.

  15. simple motion cam curve

    AndersonJr posted a topic in Mitsubishi

    Good afternoon, I have a problem in an application for a rotary knife, I'm using a MR-JE-B servo to make this movement, while my material is powered by an inverter connected to a modbus rs485 network, with a 5v encoder connected directly in motion. I'm having some problems and I think it's my cam curve. I have a very high refeneration, and the system doesn't obey the size of the length I want the cut. It always cuts the same size, regardless of the configuration I use, it always cuts to 245mm. Put some photos, how are my settings. Grateful in advance, if anyone can help me. Dover_roll_1-Motion-configuração_jog_manual.gx3
  16. Is it possible to reset " Motor replacement detected error" ( Error code 95.01) using code without connecting to PLC through sysmac studio? If yes please suggest how to do it... Thanks in advance...
  17. All of the ethercat servos I have installed are Omron. I have used many many brands in the past - over analog, pulse train, but not ethercat. I have one of the Yaskawa servopacks that can control two servos independently. The drive is all wired (POT, NOT, safety), autotuned, it's in RUN OK state, I have installed the ESI file, set up the axis, mapped the PDOs.. it's all working, but they do not move. I made a test program just with MC_POWER and MC_MOVEJOG/MC_MOVERELATIVE/MC_MOVEABSOLUTE along with the resetting of MC and EC and the servos do turn on, but ignore any movement command. They do not flare up with an error, and they give me their actual position, so the network is working. If I send the movement command the command position starts to differ, so the plc is/should be sending the command. I feel like there's something missing in the PDO mapping screen, but I didn't need to do all of this with Omron so I have no idea. I thought at first the servos needed huge units of movement and speed but the actual position value confirms this is not the case since it doesn't ever change.
  18.  What is the difference between Active Immediate homing and passive immediate homing ?   Does Motion servo axis have to be turned ON for active immediate and turned OFF for passive immediate homing ?.
  19. I have seen some programs in which they manually unlatch all bits like in figure 1, and in some programs they don't do that.  The instruction help page, ladder execution says that in pre-scan .EN, .DN, .ER, .IT bits are cleared to false So do we need to unlatch all these bits before giving a motion command like MAM ?  
  20. We currently have Delta DVP60ES2 and DVP32ES3 PLC's doing positioning control on Inovance IS 620PS2R8I 400w Servo Drives by Pulse/Direction. Under both of these environments our pulse count read on the Inovance drives are reading higher than what the PLC is outputting. We also have Mitsubishi & Inovance PLCs, which when connected to the same Inovance drives dont have any discrepancies in the pulse count. We also have Delta ASDA servo drives, which when connected to the Delta DVP PLC's also don't have any discrepancies. Given we have tested these combinations, it has led us to believe there is something unique about the pulse train output from the DVP PLC's that is causing the Inovance drives to read additional pulses. Has anyone experinced a similar issue with Delta PLC pulse output? If so what was the solution? 
  21. Hello everyone, I have this weird problem that the PC (process complete) bit of MAS command does not clear after a cycle time.  As you may probably see in the picture attached when the desired torque has been reached, the servo has to be stopped using MAS command; however, this is good only for one cycle!! The PC bit will remain on even when the whole sequence gets unlatched/reset. I have to manually reset this bit. I was wondering if you could help me with this issue, please?  Thank you!  

  22. MT Developer 2

    Willard posted a topic in Mitsubishi

    Good day everyone, I am working on a problem on a Mitsubishi Q series PLC and motion system. The system consist of a Q12H PLC CPU and 2 x Q173CPUN Motion CPUs. The first motion controller controls 23 x MR-2JS-_B Servodrive and thesecont motion controller CPU controls 6 x MR-2JS-_B Servodrives. They are all using SSCNET1 system.The machine have been working fine all along until the machine stoped for 3 months because we were waiting for one spare part that was coming from oversees during covid lockdowns. When we restarted the machine, the servodrives could not home. When we were busy checking for the problem and before finding the problem, the machine just started homing. This keeps on happening over and over. Everytime you stop the machine overnight, it just stop working then when you are busy troubleshooting, it just come to like. In the time when it is not responding, we figured out that when we jog the servodrive controlled by second Motion controller CPU for the HMI, the drives jog fine but the servodrives controlled by first motion controller CPU does not respond. I have tried jogging the servodrives indipendently using Setup161E and they move . I even changed the motion CPU but to no success. When you monitor using MT Developer 2, the are no errors. Is there anyone who might have an idea on what might be the probable cause    
  23. Hi guys,  Can someone explain me what is the difference between SS1 and SS2 instruction ? I read the help but its not so helpful for me.  THank you so much.
  24. Hi,  Can someon help me with the following question. Like what makes a Kinetix 6000 drive a Guarded drive ? What type of safety stuff can you set to make it more safe.  Is it some parameter ? I am bit confused, by the manual. Should I active it in the PLC program or how ? Or it is some setting like a safe speed or torque.  I would really appreciate any help. Thank you so much ahead.  Have a great day, thanks for the reading.
  25. Hello guys!  Im using RS Logix 5000.  Can someone explain me what is the difference between when a servo is shutdown or disabled ?  I read the help but it says the same. I can assume it like when its shutdown, there is inside some circuit which is not allow the 3 phase for the drive.  Disabled is that when it have the 3 phase but nothing can happen ? Is there any difference with the break ? Like when its shutdown it can rotate until its slow down by itself or the break will be active ?  I tried to uplod a pic but it was not succesful. When you open a servo axis properties and you choose the Fault actions tab. You can find there these settings.    Thanks a lot.