Search the Community

Showing results for tags 'module sync alarm'.

  • Search By Tags

    Type tags separated by commas.

  • Search By Author

Content Type

Find results in...

Find results that...


Date Created

Last Updated

Filter by number of...

Found 76 results

  1. Hi Everyone,I have a customer that needs a CQM1H (CPU51) replaced. They purchased the processor new-old-stock from a source they found online. It arrived in the original packaging and had the safety label around the top of the unit, so it seems that it is as advertised and no need to suspect that it would have problems. I purchased secondhand, a power supply to attach to it and program it from the bench instead of in the machine. The customer also provided me with an SD card containing the project file(s) for the machine. I am able to load the project in CX-ONE (running on Win 7) just fine. My computer has a native serial port (COM1) and I built a programming cable to work with the DB9 peripheral port according to a diagram I found online.The processor powers up right away with the ERR/ALM continuously on. No other LEDs came on initially, and after a bit of playing around with communications settings, I finally landed the right protocol and my computer seemed to identify the processor correctly. I compiled the source and attempted a transfer to the PLC. I got some failed message (or maybe messages) at the end of the transfer. It did seem to send all of the binary code, it just ended with an error message that I unfortunately didn't write down or grab a screenshot.Anyway, what I have now is a PLC processor with the ERR/ALM LED on always, I've never seen it in RUN mode, and now after the programming attempt, I'm seeing the COMM LED strobing at about a .5sec frequency (with or without a cable attached to the peripheral port), AND I cannot get CX-Programmer to again acknowledge the processor anymore. I'd like to reset this back to the way it arrived to me, but can't figure out how to make that happen offline. The DIP switches don't seem to cause that effect. I should say also that the DIP switch settings are all OFF except 3 and 7.Any help is much appreciated!Thanks,John  
  2. Problem: I am getting a control sync fault on 2 recently installed kinetix 5500 but only when my programing PC is connected to the machine network.  Install and setup all went great over a 5 day period.  Then all of a sudden I started to get this fault. Sometimes 100 times in an hour.  As soon as I go offline, and unplug my PC the problem goes away.  I have also tried another PC connected to the Machine network and still get the same result.  Sometimes machine can run for hours with my PC connected with no problem.  I do not have to be online with controller for fault to occur. Setup: I have the 2 K5500's ethernet ports daisy chained together, and then connected via shielded CAT 6 cable directly to port 2 of the Compact Logix Controller Coarse Update is set to 3.5ms and utilization's are at 33% and below.(I have tried the default 2ms with same results) Ethernet modules are configured with FW rev 7.013. Machine network is isolated.(not connected to plant network or internet) Equipment: Compact logix L33ERM Running version 30.01. There are a total of four servos in this system all running over ethernet.  2 Kinetix 350's(not affected), and 2 kinetix 5500's. I have tried: separate ethernet cables for each drive ran through a switch different ethernet cables resetting coarse update speed connecting a different PC for programming   I am just not sure where else to go with this.  Thanks in advance for any help.  
  3. We are getting a processor watchdog fault on a kinetix 5500 but I cant seem to find any information on the cause of this particular issue.  Has anyone ever seen this before? Thanks guys

  4. QD77MS4

    naderyz posted a topic in Mitsubishi

    Hi My system : plc Q03ud , simple motion module : QD77MS4 , software : Gx works2 , Application : rotary table and unit degree I send position and speed from HMI ( got 2000 ) , my problem is that when i want send 90 degree for position ( dmov d0 u0\g2006 ) , i have to enter the 9000000 from hmi . and for speed i have similar problem Position hmi ( 9000000 ) ===>> motor rotate 90 degree  Speed hmi (100000) ==>> motor rotate with 100 degree per min
  5. Hi, Does anyone know where to get EDS files for GX Works3 ?  I can't open a file that I need to access because it has an "Unsupported Module". The module is 007ER-1FL2-T, it shows up on the Mitsubishi website but I cannot see any links to EDS files or any software related to this module. Cheers, Olly  

  6. GT Designer - Alarm Screen

    seroke posted a topic in Mitsubishi

    Hello all.. I have a program for my customer.  There is an alarm page.  They want a solution screen for alarms. For example ; if there is an alarm , they will click a button near the alarm. They will see solutions for that alarms in a pop-up page. Is it possible with GT Designer  3 ? Thanks

  7. Alarm History on GT1275

    Cornato posted a topic in Mitsubishi

    I'm using a GT1275 HMI with GTDesigner3 and am trying to add some Alarm Logging capabilities. I've made an alarm page and have it working correctly, but the problem is once the display is full it stops showing current alarms. Is there a way to have it only show the 20 most recent alarms? Make it where the newest alarm deletes the oldest alarm? Or at least make it where I can scroll down to see the latest alarm?   I've attached some screenshots of the current alarm page and settings. I tried the "clear oldest history..." button but I can't set a specified target value. That may not be the right way either so IDK.  Thanks. 
  8. Hi, Is there a way to write an Event Name to a string variable in Sysmac Studio? I'm using a NJ-301. My problem is that I can detect that there is an error and get the Error Code using functions GetECError, GetMCError, GetPLCError, etc, but I want to get the Event Name associated with the code (in a string variable), to display that string on an HMI (not from Omron). Is this possible?
  9. I have a 1747-L30B SLC Brick and it is set to load from EEPROM on boot S:5/8, Error S:1/10, and Run S:1/12. I need to make changes to the program and then store it to EEPROM via "Comms>EEPROM>Store to EEPROM."  When I attempt to store the program with changes, it displays the message "Insufficient Memory Module Size." I assumed the EEPROM memory was maxed out, but I also uploaded the existing program currently stored to EEPROM, made no changes, and attempted storing it back to EEPROM and received the same message. Any advice?
  10. Good morning Today I have the honor to present you our project, on which we have worked the last months. We have been annoyed for years that when creating software in special machine building, sometimes the same/similar messages are created over and over again and then they are described similarly or the same in the machine documentation. The thought, if the mechanical components are mostly the same/similar, the error description can also be "copied" (at least initially). An Excel table with the error numbers seemed to us here a good beginning, however it would be practical, if with each message text also still the description to the message in a document, including pictures, tables etc., were deposited. This was then the point where we first thought about an online tool. This also solves problems with collaboration and makes it possible to work together. Also additional languages can be added if a machine is to be rolled out to a new market. PLC-Alarm is a young Austrian startup founded by PLC programmers to ease the handling with machine messages and their descriptions. Therefore we tried to solve the following problems besides the creation of an error list: Working together on message lists Hierarchical creation of message lists Inheritance of message texts and message descriptions to lower-level projects Adding additional message lists to make message texts more variable. Adding a description to any message text in any language via Google Docs. (Connection to Microsoft Word-online is in progress) Document template for uniform presentation Combining all message descriptions into one machine document file. Highlighting used messages to avoid having unused message text in the message list. And to shorten the machine document file. Upload a file containing the used message numbers to mark them automatically. Any export options for PLC, SCADA and HMI systems possible. (Currently optimized for TIA Portal only). Suggestions for additional features welcome As mentioned in the last point, currently only exporting for a TIA Portal text list is possible since the first customers are also programming on Siemens. But we are looking forward to extend this according to customer requirements. Do not hesitate contact us via e-mail. We invite you to test our free web applications and leave your feedback. The application is already successfully in use at the first customer and we are looking forward to more users. Homepage: https://plc-alarm.com WebApp: https://www.plc-alarm.app Thank you for reading to the end ;) Have a successful day Franz Pachinger PLC-Alarm.com Support@plc-alarm.app

  11. E-Designer

    Clandy posted a topic in Mitsubishi

    I have E-Designer 7.52 Build 344 installed on 3 windows 7 laptops the 2 that the problem is on are Pro 64 and the 1 thats working is Home Premium 64 but I seem to recall having this problem on the the Home one 9 years ago and getting it sorted but cant remember how The problem In Alarms,  Alarms New Alarm Alarm text: When typing cursor stays at left side and can only be moved to the right by the arrow key then jumps to left side after letter is pressed or you can type in reverse Signal:        Typing works normal OK:             Entry is not valid ;May not be blank Copy: Ok: Same result Properties:Ok:Same again Is there anyone who can help me with this as the laptop that works is on its last legs Thanks  
  12. Good day everybody,    Currently I am working on an application using 3-axis controlled by a QD77MS4 Simple Motion Module.  In this case, I have already set up most of the configuration, but when I try to execute the program, I get the following error:   SP. UNIT ERROR - The location designated by the FROM/TO instruction set is not the intelligent function module/special function module.  - The module that does not include buffer memory has been specified by the FROM/TO instruction.  - The intelligent function module/special function module, Network module being accessed is faulty.  - Station not loaded was specified using the instruction whose target was the CPU share memory.   The QD77MS4 Module is mounted in Base Slot #3, so I use U2\G800, U2\G1500, etc... to Read/Write from it.  The Diagnostics tool indicates the error occurs as soon as I try to access the U2\G800 Buffer Memory. If I set this part of the program to No Execution the error is no longer displayed.  Additionally, if I try to monito the Buffer Memory area of the Module, it says that "The Module Stat Address is incorrect".   I already tried changing the position of the module in the base (Slot 3 --> Slot 1) and changing the corresponding values to reflect that, but still the problem persists.    What am I doing wrong? Is there some kind of configuration I could be missing?    Thanks in advance for your help!   
  13. Hello! I'm trying to connect my QD75M2 with a MR-J2S40B1 Servo amplifier with an SSCNET cable. The problem is when I try to turn on the Servo ON/OFF on the Intelligent function in GxWorks2, an error occurs saying the servo amplifier is disconnected with my QD75M2. I'm confident that I've wired it properly. What could be the problem? Hoping you might help. Thank you.
  14. Hi, guys.I am struggling to develop a solution for a costumer in a Historical Alarm Viewer screen, I am new to Cimplicity and to database supervisory interface. Among other things, the customer is asking to:- Change the "A"; "R"; "G"; "N" notations under "log_action" column to somenthing more intuitive for the users (operation). Please have a look at the image "image.jpg";-Change the point manager process "MASTER_PTMR0_RP" log under "logged_by" column to the user that is currently logged in. Specificaly saying, when I send a command (changing a setpoint or issue a reset command, for example), although it is the user acting, the historical alarm viewer logs the action as "MASTER_PTMR_RP". I Imagine that is because this process is reponsable for exchange point data to/from the IHM points database, but it is still essential to the system administrator to know which user sent that reset command or changed the variable setpoint.The log inputs at the image "image.jpg" has boolean and integer commands (".CXX" sufix);-Log into the historical alarm viewer if the user logs out and what user logged in.It is valid to mention that I am using the ALARM_LOG table (apparently it is the only table working with the application, DATA_LOG, EM_LOG and the others simply do not work, they don't show any column at all, honestly I don't know why).I tried to use Microsoft SQL Server Management Studio to edit the table information, but, somehow, it seems to be blocked to edition.I imagine they are some specific configurations, but I have no idea on how to acomplish them. Maybe if I could use other tables would fulfill the requirements, but , like I said, they are not working (right now I am trying to re-configure the Database Logger from the beggingin to see if it works with other tables).If you could give me some inisights on how to change these settings I would be very grateful. I will be happy to give more information if needed.Thanks in advance.
  15. Hello, My coworker and I are commissioning a new panel. We have a 1732-AENTR series C remote IO thats Rev 6.1. The project file from a previous identical panel has the module at rev5.3 in the project tree. I downloaded the AOP and ran the installer, it worked no issues. My co worker then did the same thing but now the module is unrecognized in the project tree and the module is missing after installing the AOP. Im concerned he corrupted something. I tried uninstalling and reinstalling the AOP but no luck. It works on my computer but not his? TechConnect said something about corrupting the aop core. My coworker did the first install and he was getting confused about zip files and the virtual machine we run rsl5k on. Maybe he broke it? any suggestions?
  16. Has anyone found a way to put the UserAlarmViewer messages into a Label? I use 3 different alarm levels and would like to have a single line alarm banner. In NJ, I use an Array of Bool for triggers. In Siemens, I made a message banner that cycles through each message every 3 seconds from a text file and displays the string in a label. Logic is much different in Omron so rewriting is not possible, nor does Omron use VBA.
  17. Hi all, I am using alarms to generate reports through sql . But sometimes my alarms are getting missed and due to that my reports are not getting proper expected output. My alarm bit is almost high for 3 to 6 seconds , however i have observed that its getting missed . I dont know why . In below image after @22.41.03 the next snap should have been captured around @22.41.33 Instead of that it captured @22.42.03 have anyone faced issue with alarm missing issue? Any suggestions would be very helpful.   Thank you.

  18. MITSUBISHI A2SH-S1 CPU

    vipin posted a topic in Mitsubishi

    Hey i want to know that in mitsubishi A2SH-S1 CPU how can i determine that battery voltage is what and if battery voltage is low then i want to on an output so that i can change the battery with the new one so that my program does not gets erased. 
  19. Hello Sirs! I have a problem with PF527. I get alarms 'control sync alarm' and 'module sync alarm' occasionally. I suppose this meaning that PLC is missing some data from the PF527 device. How to confirm this or what should I do with the problem? Any ideas? Motion group update period is 8ms. Also this device is the last device in the ethernet line. I am thinking to pull the cable directly to the switch near PLC. I am not sure does it help?  
  20. Hello, I am new to Scada Programming. I am using Citect scada V7.50. I have completed whole project, but I am unable to generate Excel report for Alarms generated during run time. Please help me for this issue. Thanks...

  21. FBs-CBE distortion

    mohamad_r_h posted a topic in Other PLCs

    Hi every one After sending some command to plc using fatek FBs CBE module , router internet connection goes off and internet LED turn red. i mean it works fine for a minute.. then internet connection of router will be off...  why this happens?

  22. QD75M4 AND MR-J2S-40B

    herobans posted a topic in Mitsubishi

    Hello i have problem about connection between QD75M4 AND MR-J2S-40B  now MR-j2S is display "Ab" every time i can't solve this problem 
  23. I need a Red Lion HMI to communicate with an IO module (8) IO's ... I don't really need a PLC.  Because the control of a certain LinMot drive for a linear motor can be activated by IO's.  This LinMot drive can store up to 100 curves... which can simply be called into operation by a single binary number between 0 & 255,  defined by eight IO's ..  you input the number on the HMI, the HMI converts to binary and set the (8) IO's in the module which sends the binary number to the LinMot drive..   Yes, there are some other IO's for starting and stopping ... and it may be unrealistic for me to not use a PLC.   I'm trying to get the cost way down...    If a "stand-alone" IO module does not exist... then is there a simple, low budget PLC out there, with 8 or 16 IO's available..?    Thanks much, Michael

  24. IC200ALG264 Analog Input module

    lupodellasleppa posted a topic in GE

    Hello all, Thanks for the forum which has provided me with a lot of help overtime. I'm posting my first thread since I can't seem to find an answer to my issue. I'll quickly explain the situation: I'll be installing a RTD sensor to a GE Fanuc IC200ALG264 analog input module using a 4-20mA converter. Everything is fine except I can't seem to understand the polarities of the Fanuc inputs. I'll explain better: the module has an IC200CHS022 for the terminals, 15 terminals total, and the manual is reporting a "number" and a "connection" for each terminal. Now, the "number" seems to correspond to the visible pin of the terminal. But the positive and negative symbols are represented on the "connection", which I can't seem to wrap my head around what it means. Attached are abstracts from the manual and a photo of the terminals. Please tell me where to connect positive and negative outputs of the 4-20mA converter. Thank you. Terminals Table Terminals drawing Terminals photo (front)

  25. Sysmac Cj2m Cpu35

    Mohd Muhaimin Saidon posted a topic in CX-Programmer

    Dear All,  Need your help. I have problem with plc cj2m cpu35. After power trip plc error. Err HE Ip 01..what is mean? plc also connected with one pc using ethernet cable. Any suggestion need to do...