Search the Community

Showing results for tags 'modicon or schneider'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Found 81 results

  1. My CPU 534 14B doesn't work. Run led flash 7 times. no possible MB+ connection, ERROR code meanings: 300 EXEC not loaded or 301 EXEC Checksum. It was working well then nothing can't even communicate with it. reset power without battery, download an other firmware (EXEC) 1.11 instead of 1.16, same problems. Someone can help on that case? I'm using NXT as programming software.
  2. Hello all, first post here, and thanks in advance for the help. I'm a fairly green SCADA and controls designer and although I worked fairly extensively with these systems in the past, I followed a sightly different career path for the last several years and haven't had my hands on a PLC that whole time. Started a new job and am rebuilding my knowledge with it. Fortunately my company afforded me a PLC to take home and mess around with for this purpose. I feel pretty dumb as I am struggling to even connect with it, haha. Here are the stats: Backplane: TSXRKY4EX (end caps are securely in place) Power supply: TSX PSY2600 Processor: TSX P57 6634 First I attempted to connect via ethernet, using the IP address sticky-noted to the front of the processor: 10.1.1.80. No luck, "PLC address is incorrect, or PLC is busy, yadda yadda". As I understand, the default IP address can be converted from the MAC address. The last two MAC address numbers were: CF.87, which gave me the address 85.16.207.135. Same result with this. I tried pinging both address from the command console and had no luck there either. I happened to have a USB to unitelway adapter (Telemecanique brand) and attempted using that as well, Address:SYS.. Media:Unitelway. No luck, same answer. After a lot of frustration and hours spent scouring the internet for answers, I took the nuclear option and pulled the battery (while unplugged) and replaced after 30 or so seconds. I was assuming this would clear the memory and reset the IP to default (85.16.207.135), afterwhich I could reconfigure and start fresh. Unity still can't connect nor can I ping it. It should be noted that I am using Unity Pro XL Version 8.0, on a VMware image. I did attempt pinging from both the VM and the host machine, both can ping other known devices so connection by the VM through the host shouldn't be the problem. Neither the VM or the host recieved a ping reply from the PLC. Any help would be GREATLY appreciated. I feel I have exhausted all options and I hope I didn't shoot myself in the foot by pulling the battery. As far as whatever program was on it before is irrelevant, the PLC was given to me to do with whatever I wish, so memory loss wasn't a danger. I just need to connect to it. Thanks!!
  3. Hi I have a scenario where I need to setup communication between a Mitsubishi L-series PLC to Schneider Modicon M580. I need to use the onboard ethernet port of the L-series PLC. The protocol I need to use, is Ethernet IP. (socket communication). Can someone please assist?
  4. Not able to login to my new TM218 PLC. Scan yeilding no results. Pls help
  5. Dear All, I have a little problem in reading data from Power Meter to Vijeo Citect v6.0 I'm using Schneider PM810MG for Energy reading from Power Meter and for the SCADA I'm using Vijeo Citect v6.0. I can do some simple data reading like current, voltage and the others using variable tags from Vijeo Citect with Data type INT. But i dont know how to read the data for "Real Energy In" since the data range from 0 to 9,999,999,999,999,999. Waiting for all your help soon. Thx. Best Regards, Budiman Chandra
  6. can anyone please provide me how to communicate between keithley controller 2182A(nano voltmeter) and any modicon or schneider plc.aslo the programme & instruction & parameters..ASAP using RS-232 interface?