Search the Community

Showing results for tags 'mitsubishi fx series'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Found 370 results

  1. CC-Link IE Protocols

    Hello, There seem to be a lot of different CC-Link IE protocols: CC-Link IE Field Basic CC-Link IE Field CC-Link IE Field Motion CC-Link IE Field Safety CC-Link IE Control CC-Link IE TSN This causes me some confusion. Are there as many variations of Ethernet/IP and PROFINET? Can you point me to a good comparison of the different CC-Link IE protocols? My understanding is that: CC-Link IE Field Basic: 100 Mb/s Non-deterministic? Good for non-time-critical communications (e.g., setting a drive speed) Implemented in software Traffic can co-exist with other TCP/IP traffic Max 64 stations Addressed by IP address Star topology I believe the other protocols are all 1 Gb/s, are deterministic, are addressed by station number, are implemented in hardware and each needs its own isolated network. CC-Link IE Control is used for communications between PLCs and robots. CC-Link IE Field is used for remote I/O and CC-Link IE TSN is used for even faster remote I/O communications. Please let me know if any of this is inaccurate. Thanks,
  2. I've set up 20 or so of my alarms under the 'User Alarm Observation' section. I then added an 'Alarm Display (User)' object. Will this object display my alarms when they come in? I'm noticing an Alarm ID section in the 'Alarm Display (User)' object section. What is this Alarm ID for? Can the 'Alarm Display (User)' object only display one alarm? That doesn't seem to make any sense? How would I got about configuring this object so that it will show all my alarms as they come in? Thanks!
  3. Hello and good day I have a Mitsubishi fx1n-14mr PLC controlling a band saw. The PLC is connected via a DB925 - MD8M cable to a Beijer/mitsubitshi E100 HMI for communications and as a power supply via RS-422. When powered on the display on the E100 panel fluctuating, i.e. the screen turns on and off repeatedly. If the main switch is then switched off, then on again the screens seems to stay on and the machine operates normally. The PLC has a built in AC/DC power supply and I suspect that is may be the problem. Is is possible to switch out the AC/DC module? To make sure that the E100 panel is not the problem I want to connect a 5V external supply to the port located on the back. Is it safe to have the RS-422 and the 5V external supply connected simultaneously?
  4. Hi, This is my first application working with a Mitsubishi HMI GT2107-WTBD using GTDesigner 3. Is it possible to have an Ack bit going from the HMI to the PLC when the operator acknowledges an alarm? I've found how to set up comments for alarms and trigger alarms but can't figure out how to link an ACK bit back to the PLC. Thanks.
  5. Modbus Tcp Ip Simulate

    Hi guys I need to test some code in an FX5U PLC,  but I don't have the PLC here so I'm trying to simulate it in melsoft gx works 3, but how I can test the Modbus tcp/ip if I do not have an IP address for the plc  someone has ever communicate both software, gx works 3 an som modbus master software ??
  6. mitsubishi nexgenie plc target settings View File This target setting files are used with codesys software for programming mitsubishi nexgeine PLC series,    Submitter lionheart86 Submitted 01/18/17 Category Demo Software
  7. Logicmaster 6 Keyboard Translator Chart

    Hi, I was wondering if anybody could post a photo of the Logicmaster 6 IBM PC keyboard translator chart? This is a 'tear out' page from an appendix in the Logicmaster 6 programming manual. The 'Logicmaster 6 Programming and Documentation Software User Guide' Appendix C refers to this chart as follows: "This appendix contains a keyboard translator chart to use with the IBM-PC, PC-XT, PC-AT, or IBM-compatible personal computer. The chart has been printed in triplicate to provide you with extra copies. The sheet has also been formatted so that you can remove each copy of the chart from the manual for easier reference." All the hard copy manuals I can find have this keyboard chart removed and online pdf copies do not show this page. your help would be appreciated.
  8. How can i limit MRJ4 servo load?

    Hello, I am beginner at servo and its driver. i am using MRJ4A driver and HG SR102 servo motor. i want to make my servo stop or alarm when the load is over the maximum load that i set by my self. what parameter should i set to limiting servo load even if the servo motor strength enough to lift the load.?  
  9. Version 1.0.0

    6 downloads

    An example on ST is the definition of the fronts of a discrete signal.
  10. Function block on ST for algorithm DIFU DIFD View File An example on ST is the definition of the fronts of a discrete signal. Submitter drYurban Submitted 10/05/22 Category PLC Sample Code
  11. valve_control

    Version 1.0.0

    7 downloads

    A working example of an FB to control a valve from an HMI panel. Controls closing/opening times, plus a little visualization.
  12. valve_control View File A working example of an FB to control a valve from an HMI panel. Controls closing/opening times, plus a little visualization. Submitter drYurban Submitted 10/05/22 Category PLC Sample Code
  13. Hi all. I am new to Autonics and Mitsubishi. I am trying to read and write the data of an Autonics TK series temperature controller using RS-485 with QJ71C24N-R4 coupled with Q00UCPU. I have the hardware setup as attached images. Software setup are as follows:  TK4 Settings: Communication address: 01-99 Communication speed: 38400bps Communication parity bit: none Communication stop bit: 2 Communication Response waiting time: 20 Communication write: Enable Mitsubishi Intelligent Function Module: CH2: Operating: Independent Data Bits: 8 Parity Bit: None Even/Odd parity: Odd Stop bit: 2 Sum Check code: None Online Change: Enable Setting Modifications: Enable Communication Rate Settings: 38400bps Communication Protocol Settings: Predefined protocol Task to be carried out: 1. Read SV 2. Read PV 3. Write SV I have the address for the modules but I am not sure how to communicate or the program which allows to reading/writing. I had tried to follow the attached PDF but i cant key in the first line as there is a bit with "G450" which has an error stating "the device No. is over usable range" and  "An unusable device has be designated". I hope someone here could guide me in writing the program, or any reference for me to follow.  TK-Q02H_RS485_EN_Technical_support_180823_W.pdf
  14. Hi! We have a GOT2000 HMI with a Q06UDVCPU system. During an investigation, I found that the address on the HMI (for example D10120) and the address in the PLC (D10020) are different. The value is the same, it appeared instantly during monitoring, but when I searched for it, didn't find it (I couldn't find the D10120 in GxWorks2, and couldn't find D10020 in GtDesigner3). The HMI's address is 100 higher. I never saw anything like that. Where is this difference can be set? Knowing this, I can navigate in the program..it's just annoying.
  15. Simulation of FX5 in GX Works3.

    Hello gentlemen. I am working in a company that makes SCADA software, and needed to do reading/writing tests on MitsubishiPLC's, In this case I needed to do tests on FX2, FX3 and FX5. I saw that Mitsubishi makes available the GXWorks 3 software that is possible to do simulations of FX5 and FX5u in it, but I can't connect in any way to the PLC being simulated on the company network. I put the correct IP in the ModuleParameter\EthernetPort configurations, I write a simple read/write program in ladder, and I use Star Simulation, but when I try to ping the PLC, I can't find it, much less talk to it via VisualStudio . How can I connect this PLC that is being simulated in GX Works3 in an external program?
  16. serial input string

    Hi  I'm quite new to plc but very new to mitsubishi.   I have an input string eg G+002.7 which represents a weight. I wish to take in the input string then move/convert to int omitting first char,   On other plc's i have been able to use a modifier like d200[2] then the no of chars. How do i achieve this in gx works3   Any feedback gratefully recieved   Paul  
  17. Alarms Acknowledge

    Hello experts, I have a problem with Mitsubishi, specifically about alarms and their acknowledge. Basically I would like to follow Siemens logic, i.e. when I have an alarm, I acquire it and only after this step can I reset it, so every time I have an alarm and want to reset it I have to acquire it first, but this means that every time I reset it and for some reason the alarm comes back to me, its acknowoledge has to come back working.  I hope I have made myself clear.  Does anyone know if I need to set something on GT Designer3 or do I have to adapt to Mitsubishi logic and do some programming on GX Works3? Thank you very much
  18. GOT 1000 ADMIN PASSWORD RESET

    hi good day, i have problem to reset my admin password in melsec GOT1000. it's because i didn't remember my old password. please help me to solve this problem
  19. I'm editing a dual language project for an NA5 HMI. It's working fine except for the message at startup. To modify the project I've had to update the firmware on the HMI. I'm using Sysmac Studio 1.15. Startup language seems to be set correctly. Any ideas?
  20. GX Works3 Projectlib Locked

    Hello, I have a problem that I need to solve in a PLC program has it's projectlib locked.  I work for a company that contracted a PLC programmer before my time to program their new version of their control cabinets. The company did not write any specific contract with the contractor and just relied on his work. The guy later delevered a buggy software that is kind of functional (the bugs came up at the commissioning after the guy was paid and now he refuses to help or to provide more consultations). I have as a task to freshen this up and make it work without bugs, the problem is that the Projectlib is locked and I cannot access the source code.  The only thing that I can changes that I can make to the code is to put some logical circuits between the I/O of the already existing function blocks, which solved some problems, but not all and it keeps one of the most important ones as well. Anyways, that's my story, so now my question is, is there and possible way of unlocking the projectlib? Any feedback would be highly appreciated. Thanks in advace!
  21. Hello everyone I need help to Convert FX 5U program to FX 3U Plc. Is there any way to do so??? 
  22. Printinting from Mitsubishi HMI

    Hello everyone I have Mitsubishi HMI GS2110 WTBD- N. It is connected with FX5U with Ethernet protocol. I want to run a printer directly from HMI with RS 232 without using RS232 adapter card. Can someone please help me what to do and how to do. Regards
  23. is there is a function built in to convert chars like "XYZ.." to hex and vice versa ?? I am new to the iQ-R series and trying to figure it out, the GX-Works version that I am using is 1.038Q any help would be appreciated
  24. Hey, does anyone know why the simulation mode is on? how to change it? (LED SIM )
  25. fx3uc-64mt/d

    Dear All , i Have FX3uc-64mt/d    plc. i am getting confused about its wiring . In manual it is mentioned that plc can be run on both sink and source while when i connect only OV to any pin it indicates the input high. although no signal is given to common terminal . can anybody explain me this phenomenon.  thanks in advance.