Search the Community
Showing results for tags 'intelligent position servo drives'.
Found 128 results
-
Hi All, I am doing an application that use servo motor to feed plastic film to a target length (set by operator), and it need to stop immediately if marker sensor is ON. This application is control by Omron CP1E PLC. It will feed plastic film in 500-1000mm/s depends on the target length set by operator. It is require to stop immediately if the servo feed length more than 90% of the target length and the marker sensor is ON. However, is there any possibility for the servo to stop immediately once the condition is meet? As I am using PLS2(887) to feed with target length, and INI(880) to stop immediately, however, it cannot get the desired result as servo not able to stop immediately after marker sensor is ON, I am not sure is because of the PLC scan time, or servo need time to deceleration (deceleration rate assigned to #FFFF). Appreciate anyone able to assist on this. Thank you.
-
Hey everyone! New member here, and this site has always been a big help! I try to help other folks too, but a lot of guys are super quick on here. I've got a problem using some obscure components. I inherited a sensor network at work that uses Panasonic S-Link and I need to read them from a Q-Series. Panasonic makes a module that slots into the Q Series called an SL-VMEL-Q that I have. My question is: Did I do everything correctly on my Mitsubishi side? I put it into the parameters as an intelligent module with 64 points and I put the correct address in for the start I/O. Is that all I have to do? This is the first time I used a module that wasn't on the drop down list when you add one in GX Works 2. I can read and write to the buffer memory, but I can't get the unit to send to or receive from the sensors. I think the problem is that there is no end unit on the S-Link line (I don't know if it's just a terminating resistor or what), but it previously worked without one, so I can't be certain.
-
We have a controller written in C# and need to integrate a servo. We are looking at the Mitsubishi servo MR-J4 line. Unfortunately it doesn't support Modbus TCP but does have the CC-Link IE protocol. Does anybody know if it is possible to talk to CC-Link IE via C#? I'm having a helluva time trying to find an answer. I see some thing about Seamless Message Protocol (SLMP) and CC-Link but the info is somewhat sporadic. Any advice is much appreciated as I've never worked with the Mitsubishi product line (but interested in their PLCs).
-
Hi all. I have a question about how to set up the motor in rotary mode. My application will be a basic rotary table driven by a servo motor without gearbox between. So, in my servo drive axis settings, I select the motor as a rotary mode. then I defined the maximum position setting value for 360 degrees, and minimum to 0. So far so good. But the problem comes when I want to make an absolute move using the mc_moveAbsolute to move 360 degrees. Whit this settings the error "target position settings out of range " will come up. So, what is the solution to rotate 360 degrees without generating this error? if I set up the maximum value to 361 degrees and then if I rotate 360 the error will not occur and the motor will rotate 360 degrees as I aspected, but it's this correct ? or there is another way to do it? Thanks
-
Is there a real-time help resource for this thing other than the worthless AB site, on which the support page has been giving an error message for 2 weeks?
-
Hello everyone! I have problem with understanding the usage/principle of operation of parameter "Mark detection number". In manual i read: "The number of mark detections is stored. "0" clear is executed at power supply ON. Continuous detection mode: 0 to 65535 (Ring counter) Specified number of detection mode: 0 to 32 Ring buffer mode: 0 to (number of buffers - 1) Refresh cycle: At mark detection" My question is which mark detections are stored? Servo detects some kind of marks? I am novice in servo programming, please explain in the easiest way. Thanks for help.
-
Hello, I am using the R88M-1M40030T-BS2 ( 200V 3ph) servo motor. I am looking for a diagram that explains the connections on the top of motor ( for power supply).. there are more than 3 pins and i am not sure why. Can anyone help me understand the pins on the motor for the 3ph supply? Thank you
-
Posted 22 July · Report post Dear Friends, I want to set my servo controller overload setting as per my machine load requirement since all my servo installed in my machine over travelling and hitting trying to run continuously which is resulting servo failures ,repeated timing belt cut issues.Kindly help me resolve this issue.since i am not familiar with servo controllers.Model used A5 II minas servo MADKT 1507 and contol mode in position control setting.
-
Dear Friends, I want to set my servo controller overload setting as per my machine load requirement since all my servo installed in my machine over travelling and hitting trying to run continuously which is resulting servo failures ,repeated timing belt cut issues.Kindly help me resolve this issue.since i am not familiar with servo controllers.Model used A5 II minas servo MADKT 1507 and contol mode in position control setting.
-
Hi, I am trying to do a merge move on 1S Servo. The condition are as follows: Task: Move 2 in(absolute value) and then Move back to 1 in (absolute value). I have to do this move 10 times in a row. The application is material leveling after dumping in the mold. The only question i have is if I use just MC_MoveAbsolute command, the only buffer mode for transition available is velocity. Is there a way i can do it with position. I dont want to stop when I can go from 1 to 2 and 2 to 1 again and again. Its time consuming. But rather a nice oscillation motion without stopping to mimic leveling. Can anybody please help me out with this problem. Thanks
-
Hi, I'm trying to set up PLC (CJ1G) to control servo motor. I'm using position control unit CJ1W-NC413, servo relay unit XW2B-40J6-2B and smartstep R7D-AP02H servo drive. I'm reading through manuals and feels little overwhelmed with information. Everything is probably there, but it's going to take lot of effort to put it together. Can I found example program somewhere? EDIT: When I put jumper to pin 25 (X axis RUN), motor shaft is locked and motor is holding position, so wiring should be correct. When I try to run a program, I can see that parameters are changing in CX-position, but servo is not moving. Please see attached picture
-
Hello everybody, I have a question about homing servo motors. I have a project with new servos from Omron and I would like to know what is the best way to do homing for the servos and how often. Before when we have servos with encoders I was making special homing sequence and was calling by some event. I heard that new servos from Omron pretty smart and remember own position without batteries. So with this 'new generation' of servos what is the key to keep machine robust, easy for motor replacement without useless programming stuff. Regards, Scotty
-
Is there a way to change the parameter of a mitsubishi mr-j3a using fx3u plc? Need this to change the pulse output of a master servo amp to change the pitch of the other slave servo amplifier.
-
I am trying to connect a Delta ASDA-A2 Servo internal motor encoder to a Delta DVP28SV high speed counter input. I was successful in connecting the servo to the plc on position mode with an external encoder connected to PLC high speed counter. Currently having trouble in finding the correct wiring between the servo drive and the plc to count the pulses from the internal motor encoder. Attached are some figures from the servo drive manual. OA --> X0 is obvious, tried s/s to GND, COM-, VCC and VDD... no result. Any suggestion would be highly appreciated.
-
Hi Guys! I have a problem with Motion axis move (MAM) command. There is an Allen bradley servo motor what is working well. But I need to add a new program section, wich is in a specified moment, the axis should move a certain distance. I think I need to use the mam command, just I dont know how can I configure the motion control part. I need to make a new tag ? or what ? I need to use a user define ? PLS help me.
-
Gx Works 2 ve fx2n için bir fonksiyon kütüphanesine ihtiyacım var. Servo ve step motor kontrolü için. thank you
-
Hello, I have a cp1h-y20dt-d (sinking output) plc supposedly to be wired to a servo controller. The pulse control method is Pulse/Direction. I've did some manual research on the PLC and found the following diagram attached Untitled. Since the diagram above doesnt show which terminals does it connect to in the CP1H side circled red, I want to ask if those connections belong to the following diagram attached Untitled1? If so, assuming im planning to use only Pulse Output1 (Pulse/Direction method) from the PLC side, is the connection from the first diagram no.1=CCW0- , no.2=CCW1- , no.3=COM (connected to -ve) *Note: these diagrams are from omron's manual SYSMAC CP Series CP1H-X40D_-_ CP1H-XA40D_-_ CP1H-Y20DT-D CP1H CPU Unit Your replies would greatly help. Thanks and best regards, Summer
-
Hello All, I hope this post is not against any forum's rules. If so please delete. I would like to invite everyone interested to have a look at my website, which is purely about TIA Portal and everything related: TIA Portal how to There you can find articles, tutorials, tips and videos. Hopefully someone will find it helpful. There are more materials coming so be sure to subscribe to Newsletter There is also: Facebook Fanpage Facebook Group Twitter YouTube Regards, Robert Jankowski
-
hi all, anyone can hep..i use servo mr j4.. now got error 121..anything can help..i read from manual error code but cannot understand..
-
Hello, I want to connect the Siemens PLC S7-200 with MR J2S 350CP using Serial communication (RS232/422) so, is it possible or no , any one have an idea... Thank you in advance
-
I new to the Cx-programmer. I'm facing a problem where i need make the servo motor go to certain direction and stop at the direction until other signal is sensed. Is there any instruction which can be used to do the ladder diagram? is it using PWM instruction? Is my servo motor (sg90) suitable for PLC ? do i need motor driver for this servo motor? or i just have to connect to the PLC 5v ? Im using CJ1M CPU21 PLC module. Im doing a sorting system project that use the servo motor to slide the item to certain angle.
-
Hello everyone, Is there any way to communicate with Mitsubishi Servo amplifier MR-J2S-350CP through RS232 ,I prefer to use 224XP because i already have it... thank you
-
5500 Kinetex Servo Drive with L33ERM Home Entry
dipen_95 posted a topic in Allen Bradley / Rockwell Automation
I know it may sound stupid but I am new with Studio 5000 and trying to build a project where I have to home my servo drive other than the position to zero and it is not fix but rather decided by a safety switch. What I am looking for is a dynamic Home position Entry which I am able to find it in the axis parameter but not in the CIP_Structure. Is any kind of motion FB for home position set entry? Any help would be useful. Thanks PS: Studio 5000 v30, Kinetex 5500 v7.01, L33ERM processor -
Hi i am new to Mitsubishi servo drives, i want to know how to Tune the Mitsubishi (MR-JE-A-200w) servo drive Can any one guide me please
-
Looking for some servo application help. Software: I have GX works 2, GT Designer, and GX Developer. Hardware: PLC L06CPU-P, GOT2000 HMI, MR-J4-350B servo amps, HG-JR35JK motors, LD77MS2 Pulser I have (2) AC servos that will simply move an aluminum frame backwards and forwards using a FESTO belt mover and I have a servo gear reducer 20:1. I have a "simple motion module"and all of this hardware and software, plenty of time, and would really like to finish this project off. But this is my first servo and my first hmi project. I have some experience with Omron, Mitsubishi, and Allen-Bradley plc's, and consider myself novice at best. Any sample programs or help getting me started would be greatly appreciated!
