Search the Community

Showing results for tags 'i have problem to connect 2 temperature device with him delta with plc delta by rs485..when i run plc i can see the temperature change on pc but the problem in him its'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Found 155 results

  1. FX2N & Inverter iG5A on RS485

    Hello everyone, I'm a beginner in RS485 communications and i want to control 2 inverter LS iG5A via RS485 from a PLC Mitsubishi FX2N I really don't understand how i should aproach and start this part of program in Ladder Diagram, to write and read parameters from Inverters.  Please help me with an example    Thanks.
  2.   Hello, I want to regulate the temperature by a thermocouple type T with an OMRON control module TC001 / 2/3 and a CJ2M CPU14 series PLC using CX-Programmer as a programming environment. Could you provide me with an example project? Thank you for your help.
  3. Hi everyone, I want to compare 2 programs with RS logix 5000 compare but logix opens the 2 ACD in L5K, with only tags.... thx for your help
  4. Hello I would like to connect 2 HMIGXU 5512 to my Modicon M221 is it possible please?
  5. CX Supervisor Modbus RTU

    Can CX Supervisor be used as modbus RTU master using RS232/RS485 or USB/RS485 converter to connect it to PLC or panelmeter or other modbus slave units and how? Any example? Thanks in advance Goran
  6. CX SUPERVISOR

    HELLO ALL I HAVE PROBLEM CX SUPERVISOR RUN TIME WORKING WHEN I OPEN RUN TIME AFTER 2 OR 3 HOUR IT WILL STOP AND COMMUNICATION CUT FROM PLC I USE OMRON PLC AND MT NETWORK  SETTING IN PLC  ETHERNET (FINS/TCP)  I GIVE ONE IP ADDRESS  172.17.0.85          AFTER CUT COMMUNICATION THIS MESSAGE WILL COMING MY PC    - COULD NOT WRITE TO PROJECT FILE. THE DISK IS FULL,WRITE-PROTECTED OR HAS BEEN REMOVED FROM THE DRIVER  ple told me some one  how to salve this problem    
  7. Hi All, I'm testing Cx-supervisor communication with ODT Micropower PMAC controller on modbusTCP. I'm able to establish the communication using ModbusTCP driver with cx-supervisor. But, data I'm getting in is Low word first, so not able to convert properly. If anybody has tried any other option/script for this issue? I did not found any setting in Cx-Supervisor as in Kepserver, shown in attachment below: How can we swap the registers read as a 32 bit word from controller? Thank you.
  8. Hello, is there a way, to edit E5CC-T temperature controller internal program, using CP1L-EM PLC, connected to temperature controller via rs-485 communication? I can't find any information about doing it. I know that i cat change these programs, using CX-Thermo, but that is not an option. I need to do that, using only PLC..
  9. RSLINX help

    I am using rslinx in my configuration with 2 devices: windows xp computer and an SLC 5/05 CPU.  The XP PC is running a program that relies on a file that is automatically dropped in a shared folder from a separate networked PC.  The file is deleted immediately from the shared folder.  The program on the XP PC uses rslinx to control the SLC 5/05 CPU to complete the operation.  The original XP PC hard drive failed and a new PC was installed with all the necessary software and services.  Ounce I completed the  setup, the process worked for 48 hours, then stuck in one operation (one file).  Now, I can restart rslinx and the software and the process will function normally, but stall, then get stuck on one file.  There are no files in the shared folder, rslinks has not lost connection.  The original router was replaced at the same time as the PC.  I am leaning towards rslinx storing the files somewhere and stalling/stopping the operation.  I can not find files anywhere.  Does the SLC 5/05 CPU store the files?  I'm lost.  Do you have any troubleshooting suggestions?  
  10. Change Management LogIn(lost password

    I cant able to make any changes on the points (datatype from INT to DINT) on cimplicity workbench  everything thing is greyout!! i checked and found that the workbench has a change management logOn option asking to logon! Which asks for user name and password!! And No one here Now has the user name or its password!! what to do now on such cases , Also on doing modifications on logic developer validating project generates error  may be due to mismatch data type of that associated point on workbench.
  11. Is it possible to communicate from a PC program to PLC program for reading inputs and setting outputs? How can it be made ? is it possible to do from TER connector or AUX connector , without special comm module?
  12. Hi all, I have a S7-1200 CPU 1214 DC DC DC and Cm 1241 6ES7241-1AH32-0XB0 communication module.I'm using TIA Portal 14 and i connected cpu but i couldn't connect cm 1241 communication module.When i looked diagnostic i saw" Diagnostics data are not available because the current online configuration data differ from the offline configuration data.".Then i looked for what was the difference.But i didn't see.Are there anyone can help me? Thank you
  13. Hello all  i'm looking for some software to record a 100 plus channels maybe with an ascii string from a PLC? i want to be able to assign each channel with a unit and a range, flagging feature would be nice.  - selecting the channels i want to view  - auto start recording - save file and start new automatically  -view and create reports  preferably no additional hardware because of the amount of channels. this is to record an operators every move so in events of damage or plant failure we can quickly identify the problem (point the finger)  many thanks dan
  14. Hello,             I need to communicate Power meters ( GE Multilin EPM 5500P) to  GE Multilin EnerVista Software. The present communication system uses Ethernet for communication from LAN Switch to Computer. There are a few existing Power Meters which need to be connected to the  Network. The Meters having output ports as RS485. I need to use a convertor for that right. So when I contacted GE they told me to use GE Multilinet Serial to Ethernet Convertor. But due to the price and unavailability of the material I am thinking to use a universal convertor. Is that compatible for Multilin Devices?? and In Case of using a universal Convertor does we need any other drivers for that. Please Help Me.. Thanks In Advance  mnetman-a3.pdf multinet (1).pdf PM-GE.pdf
  15. CJ1W-TC102 Module Troubleshoots

    Hello Everyone. i'm in charge of a biodigester working with an old siemens plc, but today i recieved a cp1h-xa40dt-d with the CJ1W-TC102 temperature module. I need to migrate the programation of the siemens to the new one, but CX-Programmer isn´t so much familiar to me.  Basically, the old plc turns a mixer each 20, 30 and 45 minutes and i wanna make the same for the new one, adding a resistance for monitoring the temperature inside the digester. Do you have a program for me to check it out how it's done? I have the source code of siemens, idk i this could help.
  16. Problem with CX-one instalation

    Hi I have problem with the instalation of CX-One over the instalation it stops and give the message: "Error-3: CX-Server Device Driver(Generic FINS Ethernet)failed to install. Try to install it manually from CDROM (Generic FINS Ethernet Device Driver\setup.exe) at the end of instalation." Then if I go to the CDROM and try this instal manually I got the message about the "Unable to locate CX-server" but CX-server I correctly instal from CDROM with sucesfull finish message. And If I try to start CX-Programer I got the message about missing cdmapi32.dll. So what I can do about this :(
  17. Hi, I am doing a project with three Omron Cj2m cpu.  I dont know how to connect More than one Omron Cj2m Cpu Plc in a same network to communicate each other with a Internal Memory addresses. Can any one help me to understand?
  18. DELTA HMI and DOPSOFT

    Hello, I'm using HMI DOP-B03E211 and its connected to DVP12SE11R PLC . I need help with some function in the DOPSOFT program. 1) I would like to implement a function that after 1 minute of no screen touching it returns back to the main screen. 2) I have listed the alarms in the ALARM SETUP (under Options) and i would like to link every one of them to the input registers (Xi) in the DELTA controller , for instance , i want to link between the alarm : "MAIN AC FAILURE" to X0 in the PLC. how do i do that using ALARM SETUP? 3) One of the customer's requirements is : in the main screen you got three buttons : 'operational' , 'maintanance'' , 'alarm list'. - when i click on operational button and then on the alarm list it should show me only the alarms which relevent to operational mode . when i click on maintanance button it should show me the alarm which relevent to maintanance mode. how do i do that? 4) I would like to enable the option to control that alarm list through the PC - in the PC i got an Excel file that lists the whole alarms in the system . i would like to control those alarm by that Excel file - Enable / Disable the alarm through that file and save that list in the HMI. how do i do that?   thanks in advance.
  19. Trouble Wiring a Simple LED with a Micro820 Controller

    Hi everyone, Recently, I started working with the Micro820 Controller Embedded I/O. My project is simple : when the output _IO_EM_DO_00 is set to true, an LED light turns on. But, even though it's super simple, I can't make it work. Here's my setup. If you need more information, feel free to ask anything !
  20. CJ2M-CPU32 and CJ1W-TC002 help

    Hi everyone. l have a project with omron plc but l dont know omron. l have CJ2M-CPU32 and CJ1W-TC002 also input and output units. do you have a example temperature control programme for this device ? 
  21. HELP WITH WPLSOFT DELTA PLC

    Hello , I'm using DVP12SE11R Delta PLC . I would like to read data from an external device using RS485 communication. In the WPLSOFT i have informed that i gotta use MODRD command in order to read the data . but i am not sure how to use it properly.  the data is formed as one bit ('1' or '0') i wanna read 10 registers using MODRD although those registers are not ordered one after another and i know MODRD can read 6 registers one after another. Then i would like to use that bit as a Normally Open contact in the WPLSOFT and turn on a coil. i would like to get some help with it. thanks.
  22. Socket communication with Micro820

    Hi everyone ! I have a little project wich involves communication between two Micro820 controllers via TCP/IP. To do that, I started to work with TCP/IP socket. Within CCW (Connected Components Workbench), I tried to create a new socket instance using the instruction SOCKET_CREATE and set the socket address to 127.0.0.1:21. Basically, my computer through the FTP port. The problem was that it couldn't create a new socket instance (error variable is set to TRUE and status is set to 4, wich I don't know the meaning) because I didn't have a server-side application that listens to TCP/IP socket requests. That said, I found an open source application called SocketTest that listens for TCP/IP socket requests on a specified IP address and port. So, I started a listener on the following address : 127.0.0.1:21, but the error variable is still set to TRUE and status is still set to 4. So, my questions are : Is my IP address OK ? Is my port number OK ? What means the status code 4 ? Is SocketTest doing what I think it does ? Do I need to do something else before using the SOCKET_CREATE instruction ? Thank you in advance for your help !
  23. NB Designer V1.4

    I found NB Designer really struggled running on Windoze 10 Pro x 64 bit - bloody painful to be honest - on both the massively fast desktop and very fast laptop - no time to wait around - likes my horse power. Selected it to run in Windows 7 compatibility mode - way better - quite nippy actually. Highly recommended - it appears the NB Designer team may have not quite caught up with the latest Windoze OS.
  24. dvp60es2

    Hi everyone I have PLC delta dvp60es2 ,when I connect with software wplsoft v2.37 The PLC ask me to write PLC ID What plc ID I don't know please help me Best regards      
  25. I'm looking for some general information about different types of vibration/temperature sensors. What type, brand, model number, etc. will best fit my application.  Scenario: I want to monitor the vibration and temperature of multiple motors and gearboxes for a large overhead conveyor system. If an oil leak occurs and temperature increases, I want to see a temp. alert via a HMI. If a something mechanical fails, I want to see a vibration alert via a HMI.  I've looked into sensors that stick to the outside housing of the motors or gearboxes via a magnet. My concern is justifying the temperature readings. How accurate would a sensor that reads an "ambient" temperature be (compared to a thermocouple on the motor coil itself or some sort of probe)? Also, would the location of the magnet  on the motor or gearbox drastically affect the temp. or vib. readings? Has anyone had success with a similar setup? If so, what devices did you utilize? Are these systems truly beneficial?  I'm currently considering Banner's wireless products...