Search the Community
Showing results for tags 'i have problem to connect 2 temperature device with him delta with plc delta by rs485..when i run plc i can see the temperature change on pc but the problem in him its'.
Found 205 results
-
hi all, I am using SCU32 ( unit1, port2, 2wire and termination OFF) to get the RS485 data strings from the compass with setting 19200bps, 8 databit, 1 stop bit & No parity. I can send the TX string ( 01 03 00 01 00 03 54 0B) from D100 memory and write the Rx data to D2000 (01 03 06 xx xx yy yy zz zz CC CC). But the whenever the there is no RX data, The TXdata bounce back to RX. (refer to video, d100 is TX, D2000 is RX). I also tried wth SCU32 termination resistance ON. Same thing. I am not sure what is missing. Should i use different logical Port for TX and RX ? EDITED: Just tried another scenarios 1) removed the connector and tried , D2000 - was written the TX values 2) Disable the RX changing LD from P_On to P_Off. D2000 - was written to #0000 0000 0000 0000 I am not sure what is happening., Open connection also TX data bounce back to RX Appreciate all help Thanks a lot video1.mp4
-
Hello, I have been so many days trying to comunicate the multiway software trought a serial usb converter with the SCU31 device, using a omron function block to read a holding register, but I can't achieved it. Now Im receiving some frames on multiway, but there is always some errors. I was wondering if somebody in here that have worked previously with modbus and omron can be able to help me in how to configure everything corectly to be able to read the value from multiway, on the plc, and where is this value saved. I'll upload some captures to show what I have done till now.
-
Hi Dears, I have one heavy ethernet network I have 21 station PLC (S7 300) that each station have one server & I have one server that connected to all of this PLC in center. all servers are in one ethernet network I want to know that this configuration is ok? ethernet network can support these number of servers? or may be network fail?
-
Hi dears i have one cp340 (340-1AH02) that is modbus RS232 RTU master and one RS485 RTU slave. i want to use RS232 to RS485 converter is it ok? can i do this without any problem?
-
Hi guys, I'm trying to communicate with a scale controller (Rice Lake ACT20-AN) to read gross weight. Scale controller: RS485, ASCII bidirectional protocol, Baud 9600, Address 1, Delay 0, Parity None, Stop 1 PLC: Channel 1, Data Bit 7 (unclear if it should be 7/8), Parity None, Stop 1, Sum check code Exist, 9600bps, Non procedural protocol (should this be bidirectional?), Station number 2 (should this be different than scale?) I am using $Movp "$01t75CR" D6050, Movp K1 D6000, Movp K4 D6002, G.Output U8 D6000 D6050 M7000 which seems to work okay since M7001 does not turn on? I do not get any data, however, when running Movp K1 D6100, Movp k7 D6102, G.Input U8 D6100 D6150 M7100 at the same time as the G.Output instruction. I have attached the PLC program. Also, for wiring I wired the RS485+ to SDB and RDB, then RS485- to SDA and RDA as suggested by the scale controller manual. I then grounded the cable shielding along with SG and both FG connections. Any help would be appreciated in figuring this out, thank you! Scale_111219.gxw
-
Hello everyone, I have a problem with packing machine. There are some issues with one of the axis, when axis actual position is near to 1800000 some error appear and operator has to turn off machine on main contactor. This axis is working in Linear mode. I think that rotary mode would be better for this axis. And here is my question. Which instructions, and what options i should change/check when i change count mode in axis's options. Can any1 point me some manuals to read or give me some advice ? Thank you in advance.
-
Hi, I have a problem with modbus communication. I set everything as shown in the pictures and I get a error 04. What is wrong ? program.bmp ustawienia.bmp
-
Hello , I dont have experience with Mitsubishi PLC. I want to do a modification on the ethernet configuration but i dont have the source code . According the information that i read we can use GX IEC developer or GX developer but my question are : Can i upload and download the program with GX developer? Even if was previous developed with GX IEC Developer i will not do any change on the code only on ethernet configurations , add a MC communication. I have another concern about the profibus module. For the profibus is necessary another program right ? But if i don't want do any modification on the profibus is dont need it, right? My experience on Siemens when is necessary do a modification on the hardware configuration. I should have all the hadware configuration " right" it means if i have profibus i should have the right GSD to allow do modification on the configuration . But on Mitsubish i can´t understand that well . Regards Roberto Fonte
-
Dear All. i'm a new user for Janitza. and i have issue related to RS485 actually, not to Janitza itself. i have one device (UMG 96RM), where there is only RS485 (2 pin only), no RS232, no USB, No Ethernet port. i'm trying simply to connect the device to the PC, via (USB to RS485) convertor, but i'm not able to do it. for me, this is the first time i'm see (RS485 2 Pins), usually there is Ground signal also. anyway, could you please somebody help how to connect? shall i add a pull up & pull down resistors at the device? and what is the power supply i must use? noting that, i tried many things, but still nothing happened. Appreciate if somebody can help Best regards.
-
Hi I'm trying to figure out how to use the OP320-A to control the relays on the FX1N-20MR. I have mastered the OP edit tool, but I havn't learnt how to use GX Developer. The FX3U and op320 by 485 setting youtube is a good start. Does anyone have a GX Developer project file available. Is there an OP320 and FX1N or similar that comes together, pre-programmed, ready to use. I know how to write C++ programs to send RS485 commands, but this GX developer looks complicated. many thanks Tim
-
Hi all, I have Delta 12SA2 11T transistor type plc and I am confused about the output wiring, A video on youtube : https://www.youtube.com/watch?v=8kW9AwN2fs4 says that we can connect UP to +24V and ZP to 0V for sinking outputs (NPN wiring) figure1 and the reverse i.e., connect UP to 0V and ZP to +24V for sourcing outputs (PNP wiring) figure2, please see the img.png attached here with. The first one is working ok but the second one not, when i connect UP to 0V and ZP to +24V for sourcing outputs (PNP wiring) figure2 then my indicator remains always ON no mater i trigger the output on or off The manual says that the PLC only has NPN transistors in the output inside the plc then how he in the video is showing both ways. Please help me to understand this. Thanks in advance.
-
Can Mitsubishi FX3GA-60MT PLC be used as Modbus RS485 Slave? Any sample code or documentation would be very helpful. I am planning to communicate to Weintek HMI (Modbus RS485 master) to FX3GA-60MT PLC (Modbus RS485 Slave). Any other ideas would be nice. Thanks
-
Hi freinds, I have problem during the setting up the communication to HMI to take the back up. It doesnt allow me as it has been set a passsword.How do i reset the password??? Please guide me. The model of HMI is: DOP-B07S411. Somebody please say. Thank you.
-
Hallo, i want to connect Omron PLC CP1E use CP1W-CIF11 to AD4329A with RS485 communication. my wiring is CP1w-CIF11 AD4329A SDA- SDA & RDA SDB- SDB & RDB and until now, i cant get data from AD4329A. Do you have any clue for this project? Thank you Riandanu PLC to 4329A coba.cxp ad4329aex.pdf
-
Hello all, hoping for some help with an issue we currently have. We have a stationary unit provided by an automation company which is controlled by an Omron CP1E PLC unit. We have just purchased and installed the latest CX-One software with key etc as we are aiming to make modifications to the machine. When connected to the PLC via USB the drivers install however we get an error message when viewing the driver properties stating windows is unable to verify the digital signatures. When attempting to connect via USB direct online we get a failed to connect to PLC error. We have tried updating the drivers but it states the most up to date drivers are installed. Also tried uninstalling and reinstalling drivers. Anyone able to offer any advice? We have no experience with Omron so unsure if there is something we are missing. Thanks!
-
Good day sirs, i am currently asked by my boss to convert the existing delta plc to mitsubishi due to the requirements of the head maintemance... i am current ly having a trouble of converting this line MODWR and MODRD What is the equivalent of it in mitsubishi Thank you sirs
-
Hi all. I'm having the issue of an instruction executing 30 - 40 seconds after it is programmed to execute using RTC. The thing I cant figure out is that it is not happening in the whole program but only at certain parts. I've tried using different markers, registers, timers,etc. Just cant get it to work. Any ideas?
-
Hi everyone My system consists of 2 main stations with 2 CPU Q06UDEH and connected together by QJ71GP21S-SX module but I don't know how to link the address between these 2 CPU together? so can anyone help me? Thanks so much
-
using ZP.PSTRT1 for speed control and speed change control during operation in QD77MS2
diraemon posted a topic in Mitsubishi
hallo everyone ...i use mitsubishi Q00UJCPU and QD77MS2.. i try to make a speed control program and the speed wants to be changed during servo operating, i use dedicated instructions ZP. PSTRT1 (axis 1) and have tryed but it was only successful to change speed with "change speed control" function once ... is it like it? cannot change "change speed control" many times when servo operations? -
Hi, I write app to smartphone to communication omron CJ1m and Android. I want to connect devices by standard bluetooth. I plug in bluetooth adapter directly to omron RS232. I want to ask you, how i can connect by FINS command. Bluetooth device baud rate is set 9600. If i connect to omron, i sent code: "AC01" and i sent how long as omron return me "AC01" ?? And what's next command i sent? If I want read CIO 10 i sent: "0101B000000A" ? and FCS and "*" ?? how i calculate FSC? Is it XOR my data sent?
-
Hello I have a Mitsubishi FX in my production line, but I have a problem, If I lose the electric power I lose the connection between PLC and network, I need to restart the PLC for connection again of PLC in my network.
-
Hi all, I'm making a program for Delta AS228-T using ST and I want to use the pulse instruction . Is there an analogue for LDP instruction from IL for ST? Or is there another way to replace this instruction somehow? Thanks.
-
Panelview 1000 does not display correct input
Fourdigger posted a topic in Allen Bradley / Rockwell Automation
Hello I would like to first let everyone know I am new to the world of troubleshooting or programming plc's . What we have is a SLC500 system that is connected to a Panelview 1000 HMI via the DH+ network. The issue we have is the panelview displays a gate that is suppose to be closed at as gate fault. When i connect to the plc the ladder rung shows that the gate is closed. To show various positions of the gate the programmer used N13:70 as gate opened and N13:71 as gate faulted and N13:72 as gate closed. When i checked the logic it showed the bit N13:72 as engaged or true if you will. This logic is in the ladder rung that is labeled PV Status which i take is the status the HMI reads so my question is why does it show GF when it should be reading GC. Ive searched all through the logic and it doesnt appear to be wrong here is the logic the best I can simulate it ladder 6 rung 53 instruction is XIC O:13.0/11 and OTE N13:76/0 (Gate Open ) and the branch is XIC I:5.0/11and OTE N13:76/1 (Gate Fault) next branch is XIC N13:3/11 and OTE N13:76/2 (Gate Closed which this section is green or highlighted or true which ever you like) when i looked at the input XIC N13:3/11 this is what I found is that this XIC is on ladder four rung10 and has the following XIC T4:154/DN and branchoff that is XIC I:5.0/11(gate opened)XIC I:6.0/11(gate closed) which these two inputs are false or not lighted the output is OTL N13:3/11 and it is true which makes the previous rung true showing the gate closed. So why is the panelview showing the wrong position. I even went as far as resetting the HMI and the PLC so if anyone has a helpful hint I would greatly appreciate it. -
Hello, please i wish to know the right communication cable for Delta HMI DOP B07S411 and Allen Bradley 1400 PLC
Nyame Ephraim posted a topic in Other PLCs
Hello, please i wish to know the right communication cable for Delta HMI DOP B07S411 and Allen Bradley 1400 PLC -
Hi Friends, In My new project I have used two Delta PLC'S (DVP-60ES2 and DVP 14SS2) I want to communicate both through RS 485 Communication protocol.We have tried communication trough manual help.But Master Slave device not communicating.We have checked for any error code in D1130 but it always showning "K0" value.here with I have attached screen shots and complete program for yours kind reference.Kindly help and guide us to communicate. Master.pdf RS485 master trail 1.dvp Rs485 trail 1 slave.dvp Slave.pdf
