Search the Community

Showing results for tags 'fx5-40ssc'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Found 3 results

  1. Positioning with FX5U and FX5-40SSC

    Hi Friends. I need some Help with Positioning. I'm using the FX5U PLC and the FX5-40SSC "Simple" Motion Controller with Servo MR-JE-20B and Servo Motor HG-KN23K which is controlling a Linear Guide. The JOG Modus is Working, Home Position is Working too, but I cant Programm a Position where the Motor have to Drive. I hope someone can Help. Part of My Program looks like:   FX5SSC_1.stsysctrl_d.bPLC_Ready_D:=TRUE; FX5SSC_1.stSysMntr2_D.bReady_D:=TRUE; M_Ax1_PLC_Ready:=TRUE; M_Ax2_PLC_Ready:=TRUE; M_Ax3_PLC_Ready:=TRUE; IF FX5SSC_1.stSysMntr2_D.bReady_D THEN     FX5SSC_1.stSysCtrl_D.bAllAxisServoOn_D:=TRUE;      END_IF; IF M_Ax2_Error_Reset THEN          MOV( bEnable OR PLC_1st_scan , K0 , K4M700 );     M_FX5SSC_OperateError_Ax2 (i_bEN:= TRUE ,i_stModule:= FX5SSC_1 ,i_uAxis:= 2    ,i_bErrReset:= M_Ax2_Error_Reset ,o_bModuleErr=> bEnable ,o_uModuleErrId=> D_Ax2_Operate_Error);      END_IF; IF P_Achse_HomeDrive THEN          M_FX5SSC_StartPositioning_Ax2(i_bEN:= P_Achse_HomeDrive ,i_stModule:= FX5SSC_1 ,i_uAxis:= 2 ,i_uStartNo:= 9001 ,     o_bOK=> bEnable1 ,o_bErr=> bEnable2);          RST( bEnable1 OR bEnable2 , P_Achse_HomeDrive );     P_Achse_Referenziert:=TRUE;     RST( TRUE , Referenzfahrt_TP_Ein_Aus );      RST( TRUE , Fehleranzeige_P_Achse_nicht_Ref );      END_IF;   SpeicherP1:= REAL_TO_INT (Startposition_TP_P_Achse); M_FX5SSC_SetPositioningData_Ax2(i_bEN:= Beginne_FahrtP ,i_stModule:= FX5SSC_1 ,i_uAxis:= 2 ,i_uDataNo:= 1); M_FX5SSC_StartPositioning_Ax2(i_bEN:= Beginne_FahrtP ,i_stModule:= FX5SSC_1 ,i_uAxis:= 2 ,i_uStartNo:= 1);  M_FX5SSC_ChangeSpeed_Ax2(i_bEN:= Beginne_FahrtP ,i_stModule:= FX5SSC_1 ,i_uAxis:= 2 ,i_udSpeedChangeValue:= 100); M_FX5SSC_ChangePosition_Ax2(i_bEN:= Beginne_FahrtP ,i_stModule:= FX5SSC_1 ,i_uAxis:= 2 ,i_dTargetNewPosition:= REAL_TO_DINT(Startposition_TP_P_Achse) ,i_udTargetNewSpeed:= INT_TO_DWORD(Fahrgeschwindigkeit_TP_P_Achse));       IF StartPAxis THEN          FX5SSC_1.stnAxCtrl1_D[1].dTargetNewPosition_D:=REAL_TO_DINT(Endposition_TP_P_Achse);     FX5SSC_1.stnAxCtrl2_D[1].uPositioningStart_D:=1;      END_IF;
  2. MC_Power_LD_FX5SSC Power Up Error

    I am using FX5U-32MT/DS, FX5-40SSC-S and the PLC Open blocks. I am getting an Power-up procedure error status signal. Any suggestions on how to track this down? Or should I do away with block and replace it with Un\G# codes. If so what should I use to make sure the drives are ready?
  3. MC_Power Power Up Error

    I am using FX5U-32MT/DS, FX5-40SSC-S and the PLC Open blocks. I am getting an Power-up procedure error status signal. Any suggestions on how to track this down? Or should I do away with block and replace it with Un\G# codes. If so what should I use to make sure the drives are ready?