Search the Community

Showing results for tags 'field pg'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Found 7 results

  1. Hi, I am using IQ-R Series "R16ENCPU" With Inbuild CC-LINK IE FIELD "RJ71EN71" and attached CC-LINK "RJ61BT11". Problem is, Even though my remote IO cards are in Online connected with masters, I cannot able to On/OFF Remote Device station IOs in CC-Link IE FIELD network. But CC-Link Normal is working fine. Refresh settings and Network Config Settings are done, Below attached the pics for reference. I cannot able to find the problem, Can anyone help me in this.  
  2. HMI on CC LINK IE FIELD

    Hello all, kinda lazy question, but I'll rather ask, before I'll went to deep into HMI scripting. Because of a design of CC link, there are RWr and RWw Is there any simpler solution for displaying value stored in PLC, while also letting HMI operator change the value and save it to PLC, than scriting in HMI? hope it makes sense to you thank you in advance
  3. Siemens Field PG M3 - PLC Programming Rugged Laptop for Sale   Condition is Used   This is a Siemens Field PG for PLC Programming.   Purchased several years ago as part of an auction lot and has sat in my workshop since, I don't do much Siemens so this is up for sale - This is what I know about it :-   The machine has Windows 8.1 Pro 64 bit installed (Machine has Windows 7 Ultimate on the base but been upgraded at some point) 8GB ram installed It has a windows XP VM installed which runs the Siemens Programming software (Virtual Box) There is a folder on the desktop containing the original installation files, so would be easy to return back to the host machine if required. All software appears to be licensed (see pics)    Has Step 7 and Step 5 installed   Negatives - Missing the back flap & Battery not being recognised thus not taking on charge (I think this is a just BIOS update needed but not looked into it too much)   In very good overall condition, a few light marks but that's about it, still looks very good.   Comes with the original branded rucksack    This was a really expensive bit of kit in its day and still stands up as an excellent PLC programming machine   Open to sensible offers - I am located in the UK so worldwide postage will have to be calculated seperately   I have powered it up and it works well with no issues found, the PLC software all seems to work and appears fully licensed but as I am not the original owner and don't know the provenance of the machine or licenses this machine is sold with no returns or warranty provided.
  4. Hi every one, I'm new here. Is there any CC-Link IE field basic master or simulator that can be use on Windows PC, for testing  CC-Link IE field basic slave communication ?   Thanks in advance    
  5. Hello. There is a controller FX5U-32MP in the presence, the inscription "CC-Link IE Field Basic" and the Inverter (FR-A840-00170-E2-60) near the connector, the inscription "CC-Link IE Field Basic" on the front panel. I set up both devices according to the instructions. It turns out to read the state of the inverter (state, frequency). And I can not manage from the controller. Already all the settings that could have changed. Can you scribble what is wrong? p.s. Sorry for the bad english.
  6. Help with CC - Link IE Field

    Hi Im working with an iQ-R CPU wich controls 6 conveyors with a CC-Link IE Field Network, the CC-Link module is a RJ71EN71. Each conveyor has a remote I/O (NZ2GF2B1-16TE Digital outputs main module with a NZ2EX2B1-16D extension for Digital Inputs). The communication in the CC - Link IE Field diagnostic appears to be OK, but I can´t send or receive IO signals from the Batch Monitor of Gx Works 3. Thanks for your attention!
  7. Simulation in Foundation Fieldbus

    Hi Guys,  Did anyone performed the process value simulation of Rosemount 5300 Level Transmitter (FF Communication) using Emerson 475 communicator? The simulation jumper is not available physically on the device. The only simulation option in the hand held communicator available in the following path.  Configure>>Manual Setup>>Classic View>>Advanced Transducer Block>>Parameters1.. But that option too is highlighted and not editable. Can anybody help me how to simulate the value from device so that I can check in my host DCS (Siemens PCS7). Thanks in Advance, GJ