Search the Community
Showing results for tags 'eagle signal micro 190 plc'.
Found 31 results
-
possible to connect to Ethernet/IP slave from AB Micro820 ?
peternn posted a topic in Allen Bradley / Rockwell Automation
Hi, I have AB Micro820 PLC (2080-LC20-20QBB) which, acc. to the specs, can be both Ethernet/IP master and slave. I need it to be a master(scanner) and communicate with a KEYENCE DL-EP1 module, which is Ethernet/IP slave(adapter), but don't see any way to make that happen. How do you declare/configure Ethernet/IP slaves in Connected Components Workbench and how do you add slaves to your CCW project? I have an EDS file for the slave, but what to do with it? I imported it (have no idea where) with the EDS hardware installation tool which reported all was OK, but do not see the slave anywhere in the CCW. I only see in the Device Toolbox > Discover, but the only available option there is to remove it :) Thanks for any suggestions. Peter -
I am trying to use my RFIDeas pcProx plus reader with my micrologix 1400. I know that the 1400 can send and receive strings. I want to read in the id number from the reader and send it to an external database. Can someone please point me in the right direction? Thank you
-
Hello I was searching the internet and I came up with this forum. Im excited to be part of it as a newbe I have a question on a micro 1100 with pto outputs to a stepper drive. The drive I'm using is anaheimautomation MBC25081TB - Stepper Drivers with DC Input. I was told that the sourcing output of the 1100 would work fine with the clock input on the drive. this is how I wired the drive and this is how the drive looks. Im not even sure what Im doing I have the plc set up and see it pulsing but for the life of me I can't get the drive to move. Can you please tell me the errors of my ways. Im very new to this and its killing me trying to get this running.
-
Hi guys, I have an S7 200 CPU 212 PLC and it is in system fault condition. I am using MicroWin V4.0 and I am connecting via 6ES7 901-3DB30-0XA0 USB PPI cable. I have followed the steps in the help file to find the fault code but cant seem to find how to rectify it. The code displayed in the fatal errors section is: '5 Permanent Memory error on user program' I was hoping that I could upload the program to my laptop, clear the PLC memory, then download the program back to the PLC. This does not seem to be possible and I am now stuck with a PLC in fault. I do not have a backup copy of the program so if I clear the memory I will be stuck. Any advice greatly appreciated
-
Hi everyone! I have this simple problem, but cant get over it. I have structured ladder/FBD Project and i use GX works2. As topic tells I use analog signal from field. Now, i need to compare this value X (from field) to Values X1 and X2, meaning if value X is between values X1 and X2 then M1 is true. Ok, but what function i need to use for this? Best regards, Juha.
-
Hello all, I'm quiet new to control and logic systems, I'm still learning. I have to develop a circuit/logic for an application. I was wondering if Micro 810 can be used for this & the objectives of the application are: 1. whenever Signal A(0-24V) is high for the first time in the cycle and Signal B(0-24V) goes high then the solenoid X(24V) should be ON. 2.when signal B is low then the solenoid X should be OFF. 3. If in an instance signals A and B are opposite to each other for more than 2 seconds then a signal should be sent to E-stop. If not Micro 810, what are the other products that are suitable for such application? I know this can be done by normal relay board and some timers; I want to use a controller for this if its cheaper in price. Regards, _SKR