Search the Community

I am using GX Works Version 1.493P After selecting Online->Monitor -> Monitor Mode ... and doing some online debugging... I find my projects stuck in read-only mode. Even restarting the computer does not make the project editable again. Any help will be greatly appreciated.

Need Help! I uploaded structured ladder program into FX3S PLC. But When I try to read it from PLC it says the program cannot be opened. 

Hi   I'm all new to using omron but "stuck" with a project. I find the CX Programmer software (version 9.35) a bit confusing. Used Siemens a lot.  What I'm trying to do is to display date and time on a HMI showing cpu startup time. I use a "First cycle flag" that triggers once when CPU starts and then I understand that the date and timestamp is in the system variables A352 and A353. But how do I format them as a normal text? I only manage to display them as #hex-numbers. I have tried googeling but have not found an answer to my questions. edit: CPU type is: CJ1M CPU12 //Morten

Can Anyone Come Up with the Screen Shots or a video link of procedure for Displaying Real Time Sinusoidal Waveforms From Satec MFM ON GE FANUC?? I have PACsystem RX3i via Serial Communications Module-IC695CMM002 

How to read korea plc master k 250 since it can not read by using KGwin software .thanks

Dear, i am doing one project on Omron PLC with VB.net.  i am using Ethernet communication  with  VB to PLC but i am unable to show analog value on VB page please guide me how to get data of analog value in vb and show in VB.net for DI/DO i am using CIO &H0  forreading   and  &H1 for write but for analog value how i will show on VB.net.

I am unable to read FBD program in RSlogix 5000.It says editor not downloaded.I m able to see ladder logic programs.

Hi,  i want to read real time and date in simulation mode. How can i do this in Unity pro? Thanks for helping

Good morning, I'm having an odd issue with CX Programmer and have hit a wall. I'm trying to upload a previous version of a program to an existing PLC (CS1G-H CPU42) and I keep getting the following error when I compile while online: "The read protection properties which are not supported by the connecting target PLC are set. Check the unit version of the PLC." This prevents the program from being uploaded. I have a first revision CS1, manufacture in 2005 from what I can tell. This exact program has been uploaded previously, but a modified version replaced it recently and I need to go back to the older version. Things I have tried so far. without success: - Removed UM Protection - Made sure Task protection is off for all tasks - Check DIP Switch #1, which is write protection, and made sure it is off - Used "Remove Password" and "Release access" functions from the PLC/Protection menu - Used the auto-verification to confirm the configured PLC is correct - Reuploaded a full backup of H & D memory, from the older program I am able to compile the program when offline, but it chokes when online. I am connecting to the PLC via a serial cable. I haven't found any help from the CX Programmer help, or the CS1 programming and operation manual. This error message is nowhere to be found. Anyone has a clue ? I'm at a loss right now. Thank you !

Can any one help? I am trying to write logic to collect data off a Control Logic controler using V.20.03 Logix5000 software. Attached is a copy of Time and Date logic. I there an easier way?

Hello all, I am experiencing an unusual (and what appears to be an unheard of) behavior in my CompactLogix L18ER controller. I am setting the date/time of the controller from my work station, however when I GSV WallClockTime, it is reporting 4 hours different. I have asked our local resources as well as done some forum and knowledgebase searching without result. Has anyone encountered this before? Attached is a screenshot of the controller time vs. the wall clock time. This isn't mission critical since it can be manually adjusted however I would like to understand what is taking place that would cause this behavior. Thanks!

Hello All, I want to read data from a Control Logix PLC, into a PLC5/60, using Ethernet and a MSG instruction in the PLC5. When verifying the MSG instruction in the PLC5, I get an error message. "Target Address in invalid". Once I figure out how to do this I need to replicate it in another PLC5. Scope is to read the status of 4 paint pumps controlled by the CLX. If any of the 4 stop, the PLC5 needs to know, because it is controlling the paint application equipment. Source data resides in a Control Logix 1756-L63. The tag is INT type, 4 elements long, and the name is PUMP_STS_B2. The IP address of the CLX is 4.2.6.230. There are 2 ENBT cards, one in slot 1, and the other in slot 3. 4.2.6.230 is slot 3. PLC2,5 / SLC Mapping has been created in the CLX. File=421 Name PUMP_STS_B1 and File=422 Name Pump_STS_B2. The file mappings represent a binary file created in each of the PLC5's B421:0~4 in Booth 1, and B422:0~4 in Booth 2. The PLC5/60 is Enhanced series E model using the Ethernet side card. The IP address of the PLC5 is 3.26.5.61. I also created MG file types in each of the PLC5/60. MG420:0~19 in each processor. This was necessary to use the MSG instruction in the PLC5. I have searched the forums for examples of how to do this with no solid results. I am trying to follow the best practices of reading the data into my PLC so anyone who follows can tell where it is coming from. While the IP addresses are not closely related they should be able to communicate. I say this because all of our PC's are on the 4.2.6.XXX network on a 255.255.252.0 sub net and we have no issue communicating with the 3.26.5.61 IP address. Any help and advice would be greatly appreciated. Regards, Mike Carter