Search the Community

Showing results for tags 'cp1e hard reset'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Found 81 results

  1. Hi All, I am doing an application that use servo motor to feed plastic film to a target length (set by operator), and it need to stop immediately if marker sensor is ON. This application is control by Omron CP1E PLC. It will feed plastic film in 500-1000mm/s depends on the target length set by operator. It is require to stop immediately if the servo feed length more than 90% of the target length and the marker sensor is ON. However, is there any possibility for the servo to stop immediately once the condition is meet? As I am using PLS2(887) to feed with target length, and INI(880) to stop immediately, however, it cannot get the desired result as servo not able to stop immediately after marker sensor is ON, I am not sure is because of the PLC scan time, or servo need time to deceleration (deceleration rate assigned to #FFFF). Appreciate anyone able to assist on this. Thank you.
  2. how to program ladder one pb multifunction without counter function? Help me please.
  3. Hello everyone! Briefly introduction, I would like to communicate and test the following hardwares: 1- Omron CP1E (using an Option Port CP1W-CIF11) ; and 2- Arduino Nano using MAX485 RS485 transceiver. The CP1E will operate in "Modbus-RTU simple master" as illustrated in image 01. The arduino will be in slave mode address 1 and the library used is "SimpleModbus NG" ( https://github.com/angeloc/simplemodbusng/tree/master/SimpleModbusSlave ). Taking the sample in official manual ( https://industrial.omron.eu/en/services-support/technical-tools/downloads#cp1e ) , pages 248-253 in the "CP1E CPU Unit Software User's Manual" (Image 04) describes a sample communication to an "Inverter Slave". I want to use the Arduino Slave as the Inverter Slave just to be sure that all previous steps are correct. Therefore, I would like to know: 1- As illustrated in Image 02, Am I missing any resistors? 2- Should I connect the GND to the FG? 3- In this scenario, the DIP switch setup should be as illustrated in image 03? Only DIP4 is OFF. 4- Can I test it just forcing A641.00 and checking the DM Area Data, as shown in Image 05? The code used in it is the following: // Wiring: Arduino and MAX485 // RX0 - RO // TX1 - DI // D2 - DE/RE #include "SimpleModbusSlave.h" enum { REGISTER_0, REGISTER_1, REGISTER_2, REGISTER_3, REGISTER_4, REGISTER_5, REGISTER_6, REGISTER_7, REGISTER_8, TOTAL_REGS_SIZE }; unsigned int holdingRegs[TOTAL_REGS_SIZE] = { 0, 1, 2, 3, 4, 5, 6, 7, 8 }; void setup() { modbus_configure(&Serial, 9600, SERIAL_8N1, 1, 2, TOTAL_REGS_SIZE, holdingRegs); } void loop() { modbus_update(); }   Any answer can be helpful. Thank you for your time!   Regards, Jose.  
  4. PC send data to PLC

    Hello, i'm newbie for plc. i want to ask about PC/computer send data to PLC CP1E with serial communication (RS232). my wiring cable is: PC                         PLC 2                             2 3                             3 5                             9 4&6    7&8                               4&5 and if i send data from PC to PLC, my indicator in COMM is blinking. i think the cable have no problem. but if i send data from PC to PLC, the memory is not same as what i send and whatever i send data, the memory didn't change. i will attach my ladder diagram. what should i do?    New folder.rar
  5. Compare data RS232

    Halo, my name is Riandanu, I connect PLC Omron CP1E to weighing scale, and its done. i think i dont have problem between PLC and weighing scale. And i want to ask about, how to compare value from weighing scale ?  example : from the picture you can see value of weighing scale is " ST,+00160.66  g", and i want to compare it with 180 or 150 to give output on to lamp. Thankyou Riandanu       PLC to ek-i.cxp
  6. CP1E RS232 communication to my weighing

    hello, i want to connect CP1E to EK300i (weighing scale) with RS232 communication. i attach file of datasheet ek300i, wiring CP1E to ek300i and my cx programmer. if i push send data on ek300i, com LED indicator in CP1E is on. and i dont know why my cx programmer can't change data of memory with data from ek300i? what should i do?   ek300i.pdf CP1E to EK300i rs232 communication (belum dicoba).cxp CP1E to EK300i rs232 communication (belum dicoba).opt wiring rs232 ek300i to CP1E (belum dicoba).txt
  7. Hi Everyone..I'm having hard time to read Analog Sensor. I've try to read the manuals about expansion module, but still having hard time to understand it. My PLC is CP1E-N30DR-A connect with Expansion CP1W-MAD44 and I'm trying to connect with pressure sensor Omron E8F2-B10C that in a certain pressure will trigger to open a Digital Valve. is there something wrong with my setting for range? I do the setting in 4-20mA (0-5V) I attached my Program and Picture while running, the program is only for reading the pressure sensor. the result is  -600 to +600, is there a way to earn the actual result? I've tried Scaling and APR, But didn't understand, is there a guide/tutorial for it as well?   Cheers.. Albert TEST.cxp TEST.cxp
  8. Hello         I'm new for PLC, I need to set pump turn ON/OFF  in 4 time/day every day => [8:00-8:10]a.m, [11:00-11:20]a.m, [2:00-2:10-14:10[p.m, [5:00-5:20]p.m ** I have Omron PLC CP1E-N30 , Could you advise me, please ?  
  9. CX-Designer

    Hi Brothers! I need your help, currently I'm trying to connect the PLC Omron CP1E  to CX-programmer and it works, but my problem is in cx-designer, as I test the program, I have trouble in selecting connect to PLC, please see attached file. What should I do?  Answers would highly appreciated. Thanks
  10. Omron cp1e power indicator turns off

    The plc runs for a minute and then the power turns off while the supply voltage is ok. I was sure that it is for the power circuit problem inside the plc. As I had a spare power circuit of cp1h and I checked it had same voltages output (5vdc, 24vdc & 0), I replaced it. Now I cannot connect it with my laptop to change to run operating mode. Could anyone help me?
  11. I want to soft reset a CP1E PLC by program itself via external input device. is it possible?i want all the bit memory should reset.
  12. Does Omron CP1E support Ethernet/IP? i think it only support FINS not ethernet/ip . Can anybody confirm this?
  13. Hi, I am searching for a  Possibility to Set bits in Set or Reset State. How can i do that? in Example the Code in LD: and in ST EQ_E( Merker79 AND Referenzfahrt_TP_Ein_Aus = TRUE , bDummy , P_Achse_Istpos_pulse , 0 ); PLS( bDummy , Drehrichtung_P_Achse AND M8140 AND Loeschen_Positionszaehler_Achsen AND Startpos_anfahren_nach_Referenzi AND P_Achse_Referenziert = TRUE );
  14. Remote Password issue

    Hello everyone, can u help me out please, quite urgent !!! :( i have GS2107-WTBD HMI display along with FX5U-80MT-ESS, i had one of HMI designs made on GT designer 3 by earlier designer (not in my contact now). i uploaded the graphics to HMI module and later it stuck to the initial LOGO screen and doesnt move further, moreover the HMI is not communicating with PC. i suspect it had remote password with it how can i remove this issue or hardware rest the HMI with factory defaults guidance required
  15. Hello guys, i want to connect my CP1e-N30DT to modbus device like weighing scale, but i try to searching modbus with RTU but all of them use function block, i dont understand and i think my device cant use a function block.  Can you help me for connect CP1E to modbus device for get a holding register(4xxxx),input register(3xxxx), coil(0xxxx) and input status(1xxxx) with cx programmer? thank you 
  16. Hi,   I am using Omron CP1E NA 20DTD with built-in ANALOG inputs and output. I know how to deal with digital inputs. But I have no idea about analogue input wiring and programming. I tried connecting gefran LVDT PY2 directly to an analogue input of plc. But the indicator light did not turn on. Do I need to use any signal conditioner or converter? The output of lvdt is 0 to 25volts. I HAVE ATTACHED THE DATASHEET OF LVDT. DTS_PY2_06-2016_ENG.pdf
  17. Hello admin, Im new to PLC domain , i have one OMRON CP1E N30 with in built RS 232 port and ladder program to run in Homing and forward and reverse motion. I want to control the PLC from a computer using RS 232 communication. From what little i read from manual supplied for programming ,i came to know that there are two type of commands C mode as well as Fins commands. My doubt is whether these commands can read/write CIO memory addresses that are used to set and reset the motor enable/disable in ladder program through CX programmer software? for example: in my ladder program CIO memory address 30.00 is the motor enable/disable address so if i want to control externally from a PC to enable/disable the motor ,which commands should i use and is there a format to send these commands as well as the value. I am planning to build a GUI in Labview to cotrol the PLC via Serial RS 232 . How can i do it ? Thanks in advance.
  18. CP1E RS232 Setup

    Hi everyone, I am fairly new here, I have a CP1E-N40DR-A And i need to send a string of data to a printer over rs232 from the built in port on the PLC, I have had a look online and canot find any information on what I need to do. all the tutorials are for CJ2 cpus ect and the instructions that I would normally use on a CJ2 dont work on CP1E PLC's. Any help or light shed would be great,  Thanks in advance
  19. Set, Reset issue

    Good morning good people of the blog. I have a situation where I have a set, reset for, lets say, a fan.  We press manual and it sets the coil, we press Auto and it resets the coil.  Here is my problem...when we set the fan to auto, it will stay there for about 20sec or so then the coil will set itself again and go back to manual.  While watching this occur in the logic I cannot see the contact actually engage the set command. I have gone thru the logic and cannot see what could possibly change the bool back to a 1.  Any takers on this one? -James
  20. I have this panel view 1000 plus with accounts enabled but customer forgot the app password. I have both the executable and source file. Can I retrieve the password from any of both files? Can accessing configuration mode help disabling security to enter new passwords? Having the files, what is the best way of retake control over this application?    I am not experienced on AB equipment, but have general experience on automation. I have access to Factory Talk View.
  21.   Hello , can someone explain to me what the difference between the reset ( RES ) and clear ( CLR) in RSLogix software? Please respond ASAP
  22. PLC omron CP1E

    Hi guy ! I have a problem with plc omron cp1e.Please every body help me. I was used high speed counter to count clock of encoder. And I want to count up/down pulse input case.But it not excuted.also if i use pulse + direction them it ok I used CX programmer. Thanks all
  23. Dear  I have a Premium TSX P57 2634M , in module TSX DMY 28FK the red led Fault I/O starting blinked, general (shortcircuit, etc)  , all field connection was verified are  OK. Is possible reset the fault , without restart the PLC?   thanks in advance
  24. How can I do a hardware 'factory reset' on a Q UDE CPU .... NOT using any software such as GX Developer or Works? I understand in the 'Write to PLC' menu it's possbile to Clear / Format / Arrange PLC memory - this isn't what I'm asking for. Under normal circumstances we routinely reload the PLC code / parameters / intelligent function data all remotely from our offices to our customers facilities and all works well. With the newer Q UDE CPUs it is possible to scan the network and effectively do a remote bare-metal recover to a new CPU. If the Q UDE CPU became unresponsive I would like to know how to reset the CPU back to factory defaults. In this scenario we would be asking local site electricians to carry out this reset procedure - after which we would reload the code remotely from the office. Documentation says power down CPU remove BAT for > 10 mins. I’ve powered down, left in STOP state and removed BAT for 16hours - then tested this morning – IP / program perfect and online immediately without battery connected. This retention is a wonderful feature – but if I want to deliberately do a hardware factory reset how do I do it ?
  25. CP1E MODBUS Maximum Slave

    Hello everyone, so I noticed in Omron's CP1E manual, there are no certain info on maximum number of Modbus Slaves that can be attached, however the PLC itself able to connect to slave number 1 - 247 I have read from common MODBUS specs, that 32 slaves are the limit for most MODBUS connections. However there are also statements that with proper design (1/8 transceivers) that we can extend number of connected slaves to 256. Anyone have experience or info about this with Omron PLC? Thanks in advance