Search the Community

Showing results for tags 'cp-series'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Found 60 results

  1. Hello Mrplc's members I have a Korean version " goldsec Moj2" of Mitsubishi plc A0j2 I need to know the right software for it And how to get it I tried GX Developer but it didn't work because it have only A0J2h type And I tried melsec medoc (version 1.64) but it didn't have A series CPUs
  2. melsec medoc error

    Hi Mr.PLC Members, I have Mitsubishi FX16MT unit, I'm trying to transfer programs to it using melsec medoc version 1.64b but I can't  I'm receiving error "no reply from PLC system",I'm using 25 pin to 9 pin cable and I tried also to connect it with usb to serial cable but the same error appeared  my setup: PLC system        FX Bit rate                 300 word length          7 parity                    Even stopbits                 2 "windows XP" Attached are photo of my unit with my cables and the error of the program  
  3. The CC-Link system on a machine has been intermittently dropping out.  Normally the Link Scan Time runs at a solid 87ms.  When the system "drops out", the link scan time will increase.  Sometimes double, triple, or go up 10x. It happens when the machine is running or when it sits idle. There are 33 stations on the network.  The same stations do not always fault but sometimes all of the stations will fault at once (as seen in the attachment pictures.) We have changed the main QJ61BT11N, the processor, the Q62N power supply, the main backplane (base unit), all cards on the main backplane.  Is it possible for one station or one of the cables to create a network wide problem?  Any ideas thrown at us would be appreciated. 
  4. Hello Sir/Ma'am, Hope you and your family are safe in this Covin-19 Pandemic.   One of my client have a machine in their ceramic industry which has Omron PLC System. Here I am describing the PLC Hardware Structure. (CP1H-X40-DT1-D-SC) + (CP1W-40EDT) + (CP1W-DA041) CP1H-X40-DT1-D-SC (Main CPU Unit) CP1W-40EDT (First Expansion Module, on right side of the CPU) CP1W-DA041 (Second Expansion Module on right side of the CP1W-40EDT)   Client shutdown the machine before a month due to Corona Pandemic, and today restarted the machine.   Now the problem at the restart of machine... Analog Output of 0-10V DC are not sourcing from the attached analog output module for any of channels. (Used to control speed of AC Drive) We have checked the program, and verify that the program is moving the value in analog output register address, but still no output signal at the module.(Checked Using Multimeter) We have same machine at another factory so we have tried to replace the all 2 expansion module and observed that the first Digital Module is Working properly but only last analog output module is getting problem again.   I don't know much about OMRON PLC Programming so seeking for the help regarding this.   OEM have moved the data in CIO 106 for generating analog output, as well OEM has move #8099 in CIO 104 and CIO 105 at the first scan of program. I don't know very much about this programming, that's why i refer some manuals but didn't succeed yet.   Kindly help me out if possible... I have attached backup of program as well for reference...   Thanks...   Bobin Feeder.cxp
  5. Conversion from A to Q

    Good Evening everyone, I do realise that this has possibly been done before but quite a few years ago and the links no longer seem to work or links to Mitsi pages that are in Japanese, so please excuse me. I have soem A series PLC kit that needs replacing and I have bought all new Q series stuff to replace(where possible). I have been languishing a little on this project now for a few months but need to get moving. I purchased a GOT HMI and got a good deal on the HMI and the complete Mitsubishi Software Suite the local Mitsi guru said that was all I needed to get the job done. But afetr delving into what came inthe box it seems I need a A - Q Conversion Support Tool https://www.mitsubishielectric.com/fa/products/cnt/plca/pmerit/renewal/case/support_tool.html However I cannot find the software on any of the DVD's that I have and I cannot seem to find a download. So I am stuck now. Can anyone help point me in the right directon? Any Help greatly appreceiated. Thanks in advance.    
  6. stf and stop on at same time

    i have a 800 series vfd drive that when trying to start has the STF function and stop on at the same time, does this sound like a plc issue or a wiring issue?
  7. A1S68DAV parameter

    please can anyone tell me how to set A1S68DAV analog output module parameters , such as voltage output and resolution? or is the parameter can't be set at aLL (ie, fixed at -10V to 10V)?
  8. Hi everyone; I want to communication Omron NB series HMI with Allen Bradley Micro 830 PLC. I don't know is it possible. İf its that possible, help me please..
  9. Device point error between Parameter and PLC

    Hello all, I am a beginner with PLCs programming. I have an issue on GX Developer programming software from Melsoft trying to program my Mitsubishi Q-series PLC. CPU is Q03UDCPU. When the program is written and I try to upload it to the PLC, with the write to PLC window, I check -Program -- MAIN and -Prameter -- PLC/Network/Remote, click EXECUTE and a message appears : "Device point that is set in parameter is not match the device point in PLC". I can't fix it. In Parameter - PLC Parameter - Q parameter setting (window) - I/O assignment tab : I have (see image). Whe I use CHECK button it says there is no error. The X41 input device is plugged on slot 1/00. I am making this folowing the instructions a PDF I found on the Mitsubishi electric's wesite : Q-series basic course (for GX Developer). Thanks for the help, A. S.
  10. Hey everyone! New member here, and this site has always been a big help!  I try to help other folks too, but a lot of guys are super quick on here.   I've got a problem using some obscure components. I inherited a sensor network at work that uses Panasonic S-Link and I need to read them from a Q-Series. Panasonic makes a module that slots into the Q Series called an SL-VMEL-Q that I have.   My question is:  Did I do everything correctly on my Mitsubishi side? I put it into the parameters as an intelligent module with 64 points and I put the correct address in for the start I/O. Is that all I have to do?  This is the first time I used a module that wasn't on the drop down list when you add one in GX Works 2.   I can read and write to the buffer memory, but I can't get the unit to send to or receive from the sensors. I think the problem is that there is no end unit on the S-Link line (I don't know if it's just a terminating resistor or what), but it previously worked without one, so I can't be certain.
  11. Dear sir, i want sample program for modbus tcp for q series plc
  12. Hi everyone,  I am trying to use Kepware to communicate with my PLC setup which is the iQ-R Series R08PCPU.  I read the documentation which is available at https://www.kepware.com/getattachment/3daf1ac3-5c76-49ce-bbfe-f0fb1015f6cc/mitsubishi-ethernet-manual.pdf I read through the setup for Kepware and the setup procedure for iQ-R series but it still didn't work.  From the documentation, it said something about "using special ladder logic to enable ethernet communications is required.", I couldn't find anything about this online.  Here what I did in addition to the documentation: - Enabled IP Packet Transfer - Ping the PLC's IP Address which was successful Does anyone have any idea what I didn't do to establish that communication between Kepware and R08PCPU?  Thank you in advance. 
  13. Please assist me with the following; regarding the ME96SSHA-MB Power meter data transition with Melsec-Q series PLC; We acquire to read various values on dedicated Modbus storage address registers at the simultaneous into a Melsec-Q series PLC via Modbus (TCP or RTU)  for calculation purposes. Naturally, since the reading of these variables are to provide accurate instantaneous results, it is a requirement that these values are to be read at one scan.   However, as can be seen below, there is a gap in address register range – of which, if all of these are scanned simultaneously, yields an exception error when read. This error is only avoided by scanning these data sets separately – which is not ideal for our application – since accuracy in calculations is imperative.
  14. Please assist me with the following; regarding the ME96SSHA-MB Power meter data transition with Melsec-Q series PLC; We acquire to read various values on dedicated Modbus storage address registers at the simultaneous into a Melsec-Q series PLC via Modbus (TCP or RTU)  for calculation purposes. Naturally, since the reading of these variables are to provide accurate instantaneous results, it is a requirement that these values are to be read at one scan.   However, as can be seen below, there is a gap in address register range – of which, if all of these are scanned simultaneously, yields an exception error when read. This error is only avoided by scanning these data sets separately – which is not ideal for our application – since accuracy in calculations is imperative.
  15. Fuji Wsz plc

    Please send Fuji Wsz plc software download link  
  16. Cable pin configuration required.

    Required cable PIN configuration for Nexgen 1000 series PLC, MS-40M-E, NT11-SF121B-EV1 , GT1020-LBD.  
  17. GX Works2 Q Series TCP issues

    Hey guys, been looking around for a solution and I was brought here.  I'm a programmer at a place that just put in a bunch of these Mitsubishi Q series QJ71e71-100 ethernet controllers.  I wrote a TCP server in Java to try and talk to them.  I'm trying to get data sent over from a little GOT1000 test terminal.  The zp.open command is working fine and i'm seeing a good syn-ack handshake, and if i push some text to the plc from the program I get a response (even if it is always the same nonsense).  but when i try to use the zp.send it fails, I get error C1A6 on the ladder program and the q series lights up the comm error light.  I know I'm being super vague here, I was just hoping to gain some insight.  I don't much know what to expect from this forum if you guys are active or if my question even has an answer but i've been banging my head against the wall for days now.  I'm just using a tutorial program from the q series manual and a super basic tcp handler in java.  If there's any other information I can provide let me know.
  18. I'm having trouble in finding a complete manual instruction and set-up on setting up a communication on a Q-series PLC to a inverter a700/a800 via RS-485. I have a manual for fx series, are the parameters the same as the fx series? how about the program, like  starting or stopping the motor? Are they same or not? In the Q-series, do i leave switch-5 "station no. setting" blank? i just started this so i hope that i can make this work after new year. This is the manual for the fx-series plc====> http://www.automationsystemsandcontrols.net.au/PDF%27s%20Mitsubishi/Manuals/FPLC/FX%20SERIES%20USER%27S%20MANUAL%20-%20Data%20Communication%20Edition.pdf   PS: I'm mostly self study because i don't have proper training yet and my school sucks.
  19. edit comment directly from got

    hello everyone using gt designer 3, got 2000 series and IQ-R series want confirm something. it`s possible to edit comment group (that use for history, fault,etc)  directly on GOT using GOT tool or object or script? for script, searching on gs, gd list but find nothing. where the comment group is saved? thank you  
  20. Version 1.4.0

    32 downloads

    This is a custom template created for nb7w tw01b HMI. hope someone finds it useful. If you want to create custom templates for NB series hmi feel free to ask me. Cheers.
  21. View File Template for NB series hmi NB7W_TW01B This is a custom template created for nb7w tw01b HMI. hope someone finds it useful. If you want to create custom templates for NB series hmi feel free to ask me. Cheers. Submitter Aneesh Submitted 10/27/17 Category Other Omron Products
  22. Hello, Everyone . Do anyone has experience in FX1N-232-BD connect to GT11 (or other model) from Panasonic ? I try to connect them via RS232 port and I setup parameter following HMI manual but It doesn't work at all only RX led on 232-BD blinking Any suggestion ?    Matcha IMG_39346964.MOV
  23. View File GE SRTP Ethernet Driver for .NET .NET Component for use in Visual Studio.NET to create HMI/SCADA apps that communicate with GE SRTP devices via Ethernet. Supports PACSystems, Series 90, and VersaMax.   Supports PACSystems symbolic variables and CPU rack + slot specification. Does not require 3rd party drivers Does not require OPC x86, x64, and Any CPU compatible Visual Studio.NET 2005, 2008, 2010, 2012, and 2013 Compatible Most .NET targets are supported, including Web, Win Forms, WPF, console, and service apps. Build Windows Forms, console, and ASP.NET applications that run on Linux with Mono framework. Extremely high performance - 5~10 mSec typical transaction time Optimizes multiple register configurations into minimal transactions Tag database can be configured via code or visual designer Abstract base classes allow you to write generic code that works with all drivers Synchronous and asynchronous read/write methods Data change notifications Provides common user interface across all driver classes No limit on number of devices or data points Multi-threaded for high data throughput Includes extensive help system Windows, Console, and Web Example applications with VB and C# source code included. Easily connect office systems to factory floor. Free 30 day fully functioning trial version available for download Runtime-free for qualified applications   Submitter Automated Solutions Submitted 05/09/09 Category Demo Software
  24. HMI not recognized via PC

    I am trying to connect HMI( GS Series) to Laptop but every time it says " Device not recognized ".  Tried changing the port, Laptop, whole HMI.  It was working for 2-3 times after installation of new software( both Windows and GX Designer). Tries uninstalling and installing GX designer. Pls help.
  25. Hi Everyone! I try to read Analog Data in PLC Master through Salve Module (ECT-21) but i dont see any data, with an Digital Module i can read and write, but with analogic module i can't do anything. The analog module works perfect, i have 4-20ma Simulator and work fine. Modules: PLC: NJ501-1300 Slave: ECT-21 Analog: ADO81-V1 Can u help me? Regads..