Search the Community

Showing results for tags 'communication problem'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Found 224 results

  1. WeinTek to AB PLC Issues

    I am connecting a WeinTek eMT3105P to a CompactLogix L2 series PLC via the WeinTek Rockwell PLC (CompactLogix) - Free Tags driver and I cannot for the life of me get the thing to connect. I have all my tags imported and have played around with all the settings in the manuals I can find. Any help/advice would be greatly appreciated. I know my IP addresses are correct and if I connect my cable directly from the HMI to the PLC I still get the "PLC no response" message 
  2. Hello to all, I am new here, and I have a project with FX3U plc and CR 2DA 700 robot controller. Does anyone have some experience in establishing communication over FX 3U enet module and robot controller, I need to send and receive 5- 10 M registers and D integers. Thanks
  3. Hello everybody, I have network from : PC - 192.168.3.11 PLC - 192.168.3.250 I change this option in FX5U PLC in GX Works3 for Network Ethernet port --> Application Setting -> Security -Disable Direct connect with MELSOFT : Enable/disable -DO not respond CPU module search : Respond / not respond and I upload program to PLC. After upload program to PLC and restart it was impossible to connect again. I Have ping between PLC and PC, but could't write program. Always writes me Error <ES:0180840b> So to disable Security Option you should to do : 1. Open Works3 2. New Project (Choose your PLC - FX5U) 3. Online menu 4. Specify Destination Communication 5. Click twice in PLC module 6. Set Connect via hub (In my case i connect PC and PLC directly !) 7. Choose IP Address ( in my project : 192.168.3.250 , PC must be in same network 192.168.3.X) 8. Give OK 9. Connect Test. With steps I disable security options and it was enable to connect to PLC and Write data on it. I Hope that will help to other with same problem. Special thanks to : Piotr Tynor(Mitsubishi, Poland ) , Adam Syrek (Mitsubish, Poland ) , I. Ayvazova (Bulgaria) , K. Raykov (Bulgaria)
  4. Hi All, Networking guy here, looking for network experts on a AB PLC (1756-EN3TR/B v217021900) which seems to STOP ARPing for a device after 10 ARP's. The device is purposefully powered down, but when powered up, it can take minutes before the PLC sees it again. The PLC team says only changes in the PLC's logic are made. When an older backup is restored though, I do NOT see the issue somehow. 1) The devices that are powered down are back on the network and reachable within 10 seconds or so (ping). The initial thought was that they were not even on the network, but they are. Just that PLC shows a comms loss. 2) With the 'good code', the PLC, once the device is offine, keeps sending ARPs to find the device. The first one is a directed one, the subsequent ones are broadcasts. These broadcasts keep happening till the device is back online and is able to talk to the PLC again. 1st ARP after comms is lost: 474.423859     Rockwell_cf:a7:6c     Hilscher_2e:ea:08     ARP      60     Who has 192.17.150.208? Tell 192.17.150.30 Next and subsequent ARPs after the first one: 475.423471     Rockwell_cf:a7:6c     Broadcast             ARP      60     Who has 192.17.150.208? Tell 192.17.150.30 These ARPs keep happening every 1 second, till the device is online again. 3) With the bad code, the PLC, once the device is offline, sends only 10 ARP messages total and then stops sending ARPs altogethe . Then it takes 10 minutes* before it sends another one. If the device is backup online by that time, the PLC finds it right away. SO with these 2 different code bases, how is that a low level L2 protocol like ARP is impacted so much. The PLC team tells me that they have no idea and not set anything related to it. My question is where is the ARP network behaviour governed and how to change it? How can older code which supposedly only has changes in logic have different ARP behavior? * The 10 minutes interval might lead people to think it's a ARP timer and most likely it is, but then people usually ask about gratuious ARPS (garp) and I've verified that they make it through from the device to the PLC OK. If the device is offline for say a minute, the PLC mirrored port does indeed see the garps, yet at that point the PLC is no longer ARPing and regardless of that garp, it has to sit out the time till it sends a next ARP till it connects. Thus, I suspect the coming back to life process is governed by the PLC ARPing for it, and not by the detection of a garps. Thanks everyone!  
  5. Hi everyone, I want to compare 2 programs with RS logix 5000 compare but logix opens the 2 ACD in L5K, with only tags.... thx for your help
  6. CX SUPERVISOR

    HELLO ALL I HAVE PROBLEM CX SUPERVISOR RUN TIME WORKING WHEN I OPEN RUN TIME AFTER 2 OR 3 HOUR IT WILL STOP AND COMMUNICATION CUT FROM PLC I USE OMRON PLC AND MT NETWORK  SETTING IN PLC  ETHERNET (FINS/TCP)  I GIVE ONE IP ADDRESS  172.17.0.85          AFTER CUT COMMUNICATION THIS MESSAGE WILL COMING MY PC    - COULD NOT WRITE TO PROJECT FILE. THE DISK IS FULL,WRITE-PROTECTED OR HAS BEEN REMOVED FROM THE DRIVER  ple told me some one  how to salve this problem    
  7. Cimplicity 7,5

    Good Day There is a SCADA Cimplicity and controller Control logix 5561 AB. Communication between them is organized via Ethernet IP. It is necessary to transfer some tags from the Cimplicity to the controller Control Logix. How to do it better? Through Rslinx DDE OPC or write scripts in the Cimplicity? 
  8. I am using rslinx in my configuration with 2 devices: windows xp computer and an SLC 5/05 CPU.  The XP PC is running a program that relies on a file that is automatically dropped in a shared folder from a separate networked PC.  The file is deleted immediately from the shared folder.  The program on the XP PC uses rslinx to control the SLC 5/05 CPU to complete the operation.  The original XP PC hard drive failed and a new PC was installed with all the necessary software and services.  Ounce I completed the  setup, the process worked for 48 hours, then stuck in one operation (one file).  Now, I can restart rslinx and the software and the process will function normally, but stall, then get stuck on one file.  There are no files in the shared folder, rslinks has not lost connection.  The original router was replaced at the same time as the PC.  I am leaning towards rslinx storing the files somewhere and stalling/stopping the operation.  I can not find files anywhere.  Does the SLC 5/05 CPU store the files?  I'm lost.  Do you have any troubleshooting suggestions?  
  9. Is it possible to communicate from a PC program to PLC program for reading inputs and setting outputs? How can it be made ? is it possible to do from TER connector or AUX connector , without special comm module?
  10. Hi all, I have a S7-1200 CPU 1214 DC DC DC and Cm 1241 6ES7241-1AH32-0XB0 communication module.I'm using TIA Portal 14 and i connected cpu but i couldn't connect cm 1241 communication module.When i looked diagnostic i saw" Diagnostics data are not available because the current online configuration data differ from the offline configuration data.".Then i looked for what was the difference.But i didn't see.Are there anyone can help me? Thank you
  11. Hello everyone, Is there any way to communicate with Mitsubishi Servo amplifier MR-J2S-350CP through RS232 ,I prefer to use 224XP because i already have it... thank you 
  12. Greetings everyone, I am using a VERY OLD laptop, Windows 98, the correct AB cable....and only used to download programs into equipment to restore in emergencies into AB 5/04.  I was able to connect to SLC 5/04 using RSLinx (used Auto-Config, all worked correctly) , and wanted to install a program from earlier version using RSLogix500.  It seemed to download correctly, the pop-up asked if I was sure I wanted to install new program, hit YES...then said it would change channel, pop up buttons were "ALLOW" or "DENY" (something like that). I hit "ALLOW". All seemed good until I plugged HMI back in....had a bunch of codes it didn't like, so I went to install back to original version.  When I went through the same procedure (mentioned above)....5/04 and laptop no longer wanted to communicate.  I assume it has something with allowing the channel change.  As you can tell, I know Jack Squat...I'm not a programmer (duh), but was handed a computer with instructions....and now the machine is down.  Any help with getting me in right direction is highly appreciated in advance.  I searched the forum, and wasn't able to find a solution... I suppose it has to do with an in-experienced, well intending human messing with stuff he shouldn't be messing with !!
  13. FX3U PLC WITH OPTIDRIVE E3

    Hi can anyone help me to undestand more about modbus RTU between fx3u with optidrive e3 ?? I'm using rj45 with fx3u 485adp-Mb for the connection. Then specially in making the ladder program in Gx Works 2. I'm stuck understand the command code there. I'm first time using this. Please help me. Thank you.
  14. Hello   i have a versamax icu200udr064 and i want to connect it with simatic basic panel ktp 1200 dp  both support modbus rut but the problem is that i cant find GE communication driver on the tia portal by whom i program the HMI.  One more thing is that i found a communication driver for modbus rtu but the tags addresses are in the standard form for modbus, so is there any solution for this?  thanks a lot .  
  15. Hi, I'm trying to set up a TCP communication between a Q03UDECPU and a Beijer E110 panel  I've tried both TCP and UDP as "communication mode" in E-Designer. nothing seems to work.  What I'm I doing wrong Se attached files from E-designer and Gx IEC Developer
  16. Hello I downloaded a .mer file on the Panel view 1000 but it shows errors on the display graphics. i have configured the Rslinx communication several times by selecting the rigt PLC in Design and Runtime mode. I am using Facotry Talk view 8.20 and creating 5.10 runtime file. Please advice. I was able to correctly download and use the HMI on a similar machine. I dont know what am I missing on this one.    Thanks Pratik Jain
  17. I am trying to get the communication going between EZ3 EZAutomation Panel HMI and Omron NJ501-1300 PLC. I am currently using Modbus TCP/IP as a protocol. Has anybody figured out a way to do that? Or is there a better way to do this communication between HMI and PLC ? Right now I am using MTCP_Client_Connect function block to connect with HMI but it dont seem to be working. The IP address is correct along with Port no. I am still fuzzy about the Station address of NJ and the function code of the NJ for Modbus purposes. If anybody could help me out I would really appreciate it.
  18. Problem with CX-one instalation

    Hi I have problem with the instalation of CX-One over the instalation it stops and give the message: "Error-3: CX-Server Device Driver(Generic FINS Ethernet)failed to install. Try to install it manually from CDROM (Generic FINS Ethernet Device Driver\setup.exe) at the end of instalation." Then if I go to the CDROM and try this instal manually I got the message about the "Unable to locate CX-server" but CX-server I correctly instal from CDROM with sucesfull finish message. And If I try to start CX-Programer I got the message about missing cdmapi32.dll. So what I can do about this :(
  19. Hello everyone, I have difficulty to setting up the GSM configuration or the serial RTU configuration so that I allow you with another RTU. I use Schneider CPU Modicon M340 in conjunction with RTU communication NOR0200H and a Modem Schneider SR02 MOD02. This is the first time I'm working on this kind of project, want to help me, I'm stuck and I need a solution, thank you for your time.  
  20. Hi everyone, Recently, I started working with the Micro820 Controller Embedded I/O. My project is simple : when the output _IO_EM_DO_00 is set to true, an LED light turns on. But, even though it's super simple, I can't make it work. Here's my setup. If you need more information, feel free to ask anything !
  21. Hi guys. I have 1 cj2m cpu33 reciving 3bits of info from 3 other plcs (all similar type cj2m cpu 34-33) The problem is that 2 bits are ariving the third one is not. See the pictures i uploaded:   I do not know these instructions, in the other cases it was working. However i noticed that the output plc had a different adress with D950. I changed the adress to D804 as you can see on the pictures but still not reciving the data.  I guess i will have to configure somwhere else also. All i found (https://www.myomron.com/index.php?action=kb&article=1416) on internet that i have to open this datalink tool from the integrator. When i actually do that of course i just get an error: FATAL Error. Cannot read the file.   How can i make this work? Is the other way to constantly send this one bit with ethernet? Any sollutions, advices are welcome!
  22. S7-1500 FW v 2 / Profinet issues non-Siemens devices

    Hello: Has any body encountered Profinet IO cyclic communication establishment problems between the latest S7-1500 PLC with firmware 2.0 or later and non-Siemens Profinet devices which had previously passed conformance testing campaigns? Thanks for your comments.    
  23. Has anybody tried communicating Allen Bradley 5069 Compact logix PLC with Red Lion HMI ?  I am unable to communicate them in spite of adding AB tags via L5K file which gives me no error. I am able to see all the tags in Crimsion 3.0 software in development mode.  However, PLC & HMI are not communicating with each other. I am able to ping to both, using the same program in PLC of which I generated L5K file.  I think it may have something to do with the driver as 5069 is a new line of PLC Rockwell come out with only in 2016.   
  24. Hi everyone ! I have a little project wich involves communication between two Micro820 controllers via TCP/IP. To do that, I started to work with TCP/IP socket. Within CCW (Connected Components Workbench), I tried to create a new socket instance using the instruction SOCKET_CREATE and set the socket address to 127.0.0.1:21. Basically, my computer through the FTP port. The problem was that it couldn't create a new socket instance (error variable is set to TRUE and status is set to 4, wich I don't know the meaning) because I didn't have a server-side application that listens to TCP/IP socket requests. That said, I found an open source application called SocketTest that listens for TCP/IP socket requests on a specified IP address and port. So, I started a listener on the following address : 127.0.0.1:21, but the error variable is still set to TRUE and status is still set to 4. So, my questions are : Is my IP address OK ? Is my port number OK ? What means the status code 4 ? Is SocketTest doing what I think it does ? Do I need to do something else before using the SOCKET_CREATE instruction ? Thank you in advance for your help !
  25. NB Designer V1.4

    I found NB Designer really struggled running on Windoze 10 Pro x 64 bit - bloody painful to be honest - on both the massively fast desktop and very fast laptop - no time to wait around - likes my horse power. Selected it to run in Windows 7 compatibility mode - way better - quite nippy actually. Highly recommended - it appears the NB Designer team may have not quite caught up with the latest Windoze OS.