Search the Community

Showing results for tags 'balluff io'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Found 6 results

  1. Hi, I'm new to the Omron PLC, we have a job that require we change the balluff master port from IO link to Stander IO output, i read some resource online saying that it has to be done though the cx configurator, i followed the instruction and tried to remove the module connection from the cx configurator and change the parameter and add it again. during this sequence i encounter some problem, the IO size for balluff master module is 392byte input and 262byte output, i've tried to add input though D17350 and output though D17550, i was only able to add one of them successfully, when going to the other one the softerware came  up with a error saying the it exceed the total tag size that the device supported, i tried to decrease the tag size but it would now match the device IO size when i tried to register it. all i need is to change the module's function from IO link to stander IO, hope someone has experience in these area can provide me some help Thanks     
  2. I have an Omron NX PLC  NX1p2 which Supports EtherCAT . also I have Balluff BNI00HA Ecat Block(IOlink Master). I have setup communications and connected a BNI004K balluff I/O device. I managed to get inputs and i can read it as well. but to set the pins of BNI004K as outputs i have to configure the module by accessing its Index and Subindex. I tried with IOLwrite Block but it says 16#4802 error. Also an Engineer from balluff suggested me to use CoE block but while reading the description is said CAN over EThercat. WHile my devices are IOLINK.. If Anyone can Help.Please. SS1 - Is the error I am getting on IOLink instruction SS2 - Is what i did. which is an IOlink Write block from Omron SS3 - is what balluff Engineer suggested.
  3. Hello fellas. I am having trouble with understanding the communication between my AB PLC and my Balluff BNI0085, which is connected through an IFM AL1120 IO-link deivce. I am currently running a setup with an AB PLC (L18ER) that is connected to a local network through a network switch. I have connected my IFM AL1120 to this switch, and the IP configuration for both devices have been completed. The communications are made by using two add-on instructions, supplied by Rockwell: The BMC_AOI_PROC_BNI0085 instruction (For the Balluff smartlight), and the Generic_4PORT_IOL (For the IFM IO-link). I have additionally been supplied an ACD-file by my ex-coworker, containing a program that administrates the communication between the two add-on instructions. I have attached the routine from this as a PDF. What works: I can go online with my PLC, and by using the parameter "BNI0085_Mapped_Data.O" I can control the smartlight. I can change the settings for light-mode (Segment, Level, Runlight, Flexible), and the different parameters for each mode. What's the problem: When I change the Mapped_data.O to run in level-mode, I can adjust the light to show the level desired. When I try to adjust the level above halfway, the light switches off, and can't seem to be steady lit (Light turns on/off, random dimming). I speculate this might be due to the small power supply for the IO-link device, and the setting for brightness is not included in the AOI for the smartlight.  I therefore tried to adjust the brightness by connecting through the LR-device software from IFM(The same used to configure the IO-link). I added the IODD (IO-link device description, "Balluff-BNI_IOL-802-102-Z037-20190215-IODD1.1.xml") for the smartlight, and connected the device, which is discovered in the device list once the IO-link IP has been entered. I can read the values from both the IO-link and the BNI0085 devices, and I can write parameter settings to the IO-link device. Whenever I try to edit any parameter for the smartlight, I get the error attached. I am currently trying to follow the SmartLight userguide for the Balluff, as it describes the brightness setting as being in the ISDU index 51hex, but I don't know how this pertains to the AOI.   I am in over my head with this issue, and I don't know what information is needed or what is unnecessary. I've tried to include all that I think is relevant, I'll gladly provide what might be missing.  Any help is greatly appreciated, cheers :)   Balluff_smartlight_com_MainRoutine.pdf
  4. Anyone know of a guide about programming a balluff io master device into Sysmac Studio?
  5. Good day, I need help, how I read data from Balluff BVS001C Identification over ethernet? Thx a lot
  6. Mitsubishi QJ71PB92V and Balluff BNI PBS-507-000-Z011

    Hi all! I need advice. I have Mitsubishi Q02UCPU with profibus module QJ71PB92V. I try to connect communication module from Balluff BNI PBS-507-000-Z011 via Profubus without success. Everytime I connect module, I see diagnostic alarm "The parameter transmitted by the master is incorrect". All settings were made by default. QJ71PB92V has 0 adress and Balluff BNI PBS-507-000-Z01 has 11. I connected this module to the Siemens CPU-315 and it is work correct. From this forum I see it is common error. What will be the next step to check or solve the problem? I am not profficient in Profibus networks, so I will be appreciate for any help!