Search the Community

I have restored a crashed IFIX to a new PC. The restore is ok and installed GE9 driver. With the GE9 power tools, we can observed that data transmits and recieve. The problem is that the screen scada is not updating i.e. no status/feedback, anything is happening. The LAN network TCP/IP was configured i.e. IP, subnet and gateway. Any remedies/advice is most welcome. Please provide a guide on the communication/configuration setup. Thanks

Power SCADA Expert 8.0 Need help. May I know how to start for this power scada and how to use Template Editor, Profile Editor, and the equipment editor?

Hi everyone, Currently i am having a PGP server fail to connect to the node as per the ICI status screenshot as per link below. https://www.dropbox.com/s/0qg435zkqzou9p3/Node%20Disconnected.bmp?dl=0 Appreciate anyone can assist me on this matter. I'm a new control engineer who just started working in a power plant and has limited exposure to the troubleshooting of this and i really hope that any of you can assist me. Thank you very much.

I have an EP24DC module that will not supply power to the bus. Swapped the module out and still have the same issue. Any Idea's !

At work we have been having a slightly increasing number of instances where the Micrologix 1400 that is paired with a Panelview C400 resets values when we cycle the power. Originally we thought the solution was a bad battery in the ML1400. This was the case the first few times that it happened. However, we recently had one doing the same thing and when the program was loaded onto another PLC and HMI combo it had the same issue. So either the battery for both just happen to be bad, or there is something in the program that is forcing the values to automatically reset when the power is cycled. I cannot post the program on here but I can tell you that the tags that are being reset are only used in the PLC program once. There are six total that are being reset and they are the high and low range in an SCP function that is used to scale inputs. I will be testing the program myself in house on a bench setup, but I wanted to get this question out there as soon as possible in case it is not an obvious problem. Has anyone seen this before? Any suggestions? If I come up with an answer I will post it. Thanks.

Hello. I'm having another issue regarding NT2S Display. Again I'm trying to convert my old project I made in NT2-ST software to NTXS software. I'm now having problems with: how to automatic go to screen1, if user doesn’t press any key for let's say 2 minutes? In old SW I have constantly checking DM00000 (screen trigger register) in PLC. If screen reg didn't change for 2 minutes I have write 1 to DM00000 (screen trigger register). With new software you cannot write to screen register directly. Or am I wrong? Did anyone do this function using NTXS software? Best regards.

In our SIMATIC OP7 console ram failure message is appering while power on, do anybody know about the problem and its remedy ?

I have several Mitsubishi Melsec Fx-1n 60 plc's that sometimes go for weeks without the equipment getting powered up when not in use. I know that it has the eeprom memory- does anyone know of a cheap effective hack to attach a battery or other device to the plc to retain the memory? I thought of attaching a battery backup unit from staples to it-any thoughts? The program operates ink pad printers which has several "jobs" in memory- (with parameter settings) it loses. This is leading to excessive set-up time when production is required. Any help is greatly appreciated!

I wonder if there is version of Ethernet Remote IO that can be used with 115VAC supply rather then 24VDC? This would save me a power supply which is really needed for this module only.

Dear All, I have a little problem in reading data from Power Meter to Vijeo Citect v6.0 I'm using Schneider PM810MG for Energy reading from Power Meter and for the SCADA I'm using Vijeo Citect v6.0. I can do some simple data reading like current, voltage and the others using variable tags from Vijeo Citect with Data type INT. But i dont know how to read the data for "Real Energy In" since the data range from 0 to 9,999,999,999,999,999. Waiting for all your help soon. Thx. Best Regards, Budiman Chandra