Search the Community
Showing results for tags 'auto run mode'.
Found 28 results
-
Hi all. I have a 1769-IT6 thermocouple/mv input module. It is connected to a micrologix 1500 unit. The green okay light illuminates on power up, but after you download the program and put it in run mode the processor faults. Terminal block with the cjc's are on the unit. The error message just says the I/O module has encountered an error. The hex code under status bit 6 is 179h. This error code is not in the manual. Has anyone else encountered this? Oh and I only have channel 0 enabled for type k thermocouple. Has anyone else had this issue, or know if it is a configuration issue. Any help would be appreciated. Thank you.
-
Hey, does anyone know why the simulation mode is on? how to change it? (LED SIM )
-
analog output card 1734-OE2V parameters, fault/actions, program mode
Jiggadoo posted a topic in Allen Bradley / Rockwell Automation
I have an analog output card 1734-OE2V and there is in the fault/actions page parameters for program mode. What is program mode and when it is activated? Fault mode is clear but... Program should be written the value, but when this happens? -
Hello Guys! I have couple of questions about tuning an ab servo motor. -Actually what does the drive or plc doing when I launch a servo auto tuning? - What are the little boxes like position error integrator ? There are checkmarks in fornt of the lines. Can I choose the methode or something? I mean its not "auto" ? Why it is auto then ? - Can someone send me some basic literature where they explain me what these stuff acutally meaning ? - What is the hook up test what for is good ? -When you are doing a servo auto tune what are the parameters that you are monitoring and why ? -I should do the auto without or with load ? Whats the difference ? I know there are so many question I would be so grateful if someone could help me with these answears, or even just with one. Thanks again.
-
I am looking for how others have set up vertical axis motions using the Kinetix 5700 servo system. I have a 2 axis pick/place unit with a horizontal axis (X @ 2500mm) and vertical axis (Z @ 1200mm) that works as designed during normal operation. X axis has no holding brake and Z axis has a factory installed 24vdc to unlock brake. There is a GuardLogix L81ES control system that handles the safety and control. On pressing E-stop/opening Gates the vertical axis will stop the motion, apply the brake and hold with no problems. (2198-D032-ERS3 Drive, 2198-P031 Bus Power, MPL-B430P-MJ72AA X Axis, MPL-B330P-MJ74AA Z axis) The issue that I ran into was an accidental download of the program without activating the e-stop and the vertical axis dropped unexpectedly when entering program mode on the processor. I am aware that this instance was my fault as the programmer, however I am also concerned that this might occur again in the future if the controller ever enters fault mode or someone else completes a download. I have done some investigation with the "ProgrammedStopMode" parameter on this single motion axis and attempted all 5 options and the vertical axis still has a free fall drop for a second before the brake grabs hold - so evidently this is not working for me. (Page 24 of Vertical Load/Holding Brake manual - https://literature.rockwellautomatio...t003_-en-p.pdf) I am curious if there needs to be something done elsewhere as the X and Z axis are set up as coordinated axis? I also am unaware if I need to preform some action/parameter with the bus power supply for this? The current state of the machine as it sits now is preforming a MSF in manual mode after 5 seconds of inactivity or 30 seconds in auto mode. This axis is usually in demand every ~22 seconds. This will shut down the axis after preforming a brake test on the vertical load and seems to function OK, however it is still in the back of my mind the issues mentioned previously if we ever enter a controller fault while indexing. Thanks for your insight
-
Load different programs on power up with compact logix
FesterMT posted a topic in Allen Bradley / Rockwell Automation
Hi All, Just wondering if anyone here has any experience with automatically loading different programs to compactlogix. I am open to any suggestions. So far we have been putting sd card slots on the main panels since the extender cables are limited in length so the customer needed to swap sd cards on a tooling plate change out before powering up. One of our customers now would like to change the tooling plate and have the plc automatically load the proper program for it. We don't want to have multiple subroutines because sooner or later the plc memory will run out. We also have put smaller plc's on the tooling plates themselves to hold the specific programming for the tooling plate and handshake with main frame but this particular customer does not want this. I would like to know if anyone has done anything with wifi sd cards in CompactLogix or loading the program automatically from a pc to sd card and then switching the sd card to the plc via some kind of sd card switch before powering back up. Any advice is greatly appreciated. Thanks in advance. -
Has anyone had issues using the Auto-Updater and Administrative Rights? I am running Windows 10 Pro, 64Bit. I need to update Sysmac Studio from 1.31 to 1.4.....when I run Auto Updater (as Administrator) I always get the error "Log on the PC as a user who has an administrative right when install" and it never makes it past the first module of the CX-One Update. I even gave the issue over to my IT guy and he has absolute full rights to every nook and cranny on my laptop. I was told that I needed to allow the CX-One to updates as well since they share some of the same components. My IT guy even tried to do the "download" and install individual modules of the update and that still didn't work. Currently waiting on callback from OMRON Tech Support, thought I'd pose the question here as well....thanks.
-
Hello everyone, I have a problem with packing machine. There are some issues with one of the axis, when axis actual position is near to 1800000 some error appear and operator has to turn off machine on main contactor. This axis is working in Linear mode. I think that rotary mode would be better for this axis. And here is my question. Which instructions, and what options i should change/check when i change count mode in axis's options. Can any1 point me some manuals to read or give me some advice ? Thank you in advance.
-
Has anyone had an issue with Siemens plc's occasionally going out of run mode? I was doing some research and found that it could be due to a bad analog input. Is there a way to tell which input or output is causing this fault? I know I can create a hardware diagnostics error organization block but that only correct from what I've read. Edit: I've added a screen shot of the diagnostics report. The fault that may be the problem is: Temporary CPU error: Serious firmware exception CPU changes to DEFECTIVE mode (system reaction) This plc / system was installed 2 year ago and we've had this problem occasionally since. I'm guessing the wrong firmware was used during the install. Will try upgrading firmware this weekend.
-
Hello PLC experts, I am master student currently writing thesis. For this, I have a initial task of making some changes to PLC program (Just started getting to know about PLCs- complete beginner). I have a BECKHOFF cx 9020 PLC connected to my notebook using ethernet. I am using TWINCAT 3.1 (VS) as IDE. Firstly, I cannot find my PLC IP address connected to my notebook . I added the route in the Twincat and it shows the PLC is connected. When, I am trying to run a program (activate boot project), I am unable to login to the PLC. It gives an error "login failed for application port 851". What I undertood from BECKHOFF scripts, there is something wrong with the ADS ams net ID which I am trying to figure it out. I appreciate all the help. Thank you.
-
Dear All, I am having a problem with my cimplicity Auto Report Generation, When I Click on Generate Report, it shows "0 values collected" does anyone knows what's possibly could gone wrong here ??
-
Hi all. I have a question about how to set up the motor in rotary mode. My application will be a basic rotary table driven by a servo motor without gearbox between. So, in my servo drive axis settings, I select the motor as a rotary mode. then I defined the maximum position setting value for 360 degrees, and minimum to 0. So far so good. But the problem comes when I want to make an absolute move using the mc_moveAbsolute to move 360 degrees. Whit this settings the error "target position settings out of range " will come up. So, what is the solution to rotate 360 degrees without generating this error? if I set up the maximum value to 361 degrees and then if I rotate 360 the error will not occur and the motor will rotate 360 degrees as I aspected, but it's this correct ? or there is another way to do it? Thanks
-
Anyone knows if there is a C-mode hostlink library for NJ/NX ? Also, a C-mode hostlink library for CP1L could be helpful, to translate such a library to work with NX1P is probaly less work whan writing a new library. Maybe Omron France has developed such a library? - they seem very active.. Background: Looking into writing a programmatic c-mode hostlink master for NX1P12, this is for connecting the handheld NSH5 HMI to the NX1P12 via RS232C using a CIF01. I have the hardware set up, and an machine built, expected some compatibility efforts by Omron.... but the NSH5 seems to talk C-mode hostlink, and the CIF01 only seems to support the FINS version hostlink. On the NJ you can of course add an SCU module, thus not need a library. But working with NX1 ( due to limited space available ), you are dependet on available CIF-modules which do not support C-mode hostlink.
-
Here is a link to a thread on a recent post showing how to communicate serially to an Omron PLC using VB.Net. This uses the Omron Host Link serial protocols. (C-Mode Commands) It will read 10 DM registers and display them on the form. http://accautomation.ca/implementing-the-omron-host-link-protocol-vb-net/ Here is the source program that can be downloaded. Other links: VB6 Program: http://accautomation.ca/how-to-implement-the-omron-plc-host-link-protocol/ VBA Program: http://accautomation.ca/how-to-implement-the-omron-host-link-protocol-part-2-vba/ Regards, Garry www.accautomation.ca
-
Hi, I have some trouble with a CJ2M-CPU33. My client did a backup to memory card earlier today, and after this we did some changes through remote link. Now the client wanted to restore the previous backup to the PLC and has done so, but the system would not function correctly. After going online on the PLC it seems like the PLC is stuck in "Stop/Programming Mode". When trying to change to "Monitor" or "Run" mode a dialog comes up containing the following message: "Failed to change the operating mode. The operating mode may be still changing in the PLC." - All the dip switches are set to off after restoring backup - The PLC has been rebooted - I have downloaded the application again through CX-programmer - Verified that the PLC is set to start up in "Monitor mode" But nothing helps. The same message comes up when trying to change the operating mode. Hoping anyone can help to resolve this issue as it is very critical for us and the client. In advance, thanks for any tips or help received. Best regards Stian
-
I’m using a Omron NJ to manage a LinMot linear motor .. all is going very well; however, there have been a few times during this development phase when the actuator, or programming creates a fault, perhaps from a following error, or exceeding a limit. The result is sometimes scary. The actuator might accelerate into a hard stop. Not a big deal, the ends are protected with Sorbothane, so it isn’t a big problem .. yet. Once the system is correctly programmed, it shouldn’t ever accelerate an actuator into the hard stops. In spite of my newbie-ness to Omron programming I’m aware of the need to employ error & fault action that will stop a run-away actuator in closed-loop control, rather quickly. Just how to do that.. has evaded my research. I’ve noticed: “FaultHandler” in the W507 & W508 Manuals. And, been quite frustrated to not find any reference to FaultHandler or FaultHandeler() .. which kinda suggests it’s a program?… and also expected to get some clues in the "NJ Programming Best Practices V1.1” so far… no luck. Perhaps I’m going about this all wrong.. The LinMot Driver Controller might be the way to go.. An error message from the NJ to the LinMot drive would quickly shut down movement in closed loop .. instead of turning the motor into a rail gun… Any suggestions at how to do it with the NJ, would be greatly appreciated.. Thanks Regards, Michael PS: here’s the progress so far, thanks to many out there, and on this forum ... https://www.youtube.com/embed/B0UGm9JTw3U?rel=0
-
Micrologix 1400 reverting to Remote Mode on its own
jspobuk posted a topic in Allen Bradley / Rockwell Automation
Hello, As the title indicates, we have a micrologix 1400 that has been installed for a long time. Recently it faulted out on 71h and was in Remote Mode. Do these PLCs revert to Remote Mode when in a fault condition? We placed it back in Run Mode and everything worked fine, but how did it get to Remote Mode in the first place? Thanks, J -
Hi all, I have created a program using the binary counter and timer instructions and everything works fine (yay!), but I am not entirely sure if there is a major difference between using Binary mode or BCD Mode on the PLC. Does it just come down to personal preference or is there an advantage to using a particular mode over the other? Also, does the operating mode affect anything besides counter/timer? The option in CX-Programmer seems to indicate it doesn't. Cheers, Jay
-
I got a CJ1M CPU11 that I can connect to but I can just go to run mode but when I try to switch to program mode I'm tell that I can modify the mode
-
Activation of Rockwell software in windows XP Virtual mode
dynamicboy posted a topic in Allen Bradley / Rockwell Automation
Dear Friends; Good day. First i install the windows virtual xp mode on Windows 7 64 bit. After installation i installed the FTM, RSLINK,and rslogix 5.0 in virtual xp mode. Then i activate the software by Factory talk manager and select the hard disk and for a single computer activation. This process successfully acomplished. But when i open the RSLOGIX it shows popup that activation path is not found. Then i again open the factory talk tool and note that there is no activation shows in current activate products, But the activation detail shows in the RE host tab. I re hosted the activation by using go to Rockwell site and message show successfully activation re hosted. *** Now i am stuck here is i loss my activation? *** in windows xp virtual mode how i activate my product that application find the correct path of activation file? ** In windows xp mode if i open my Computer there is shows other hard drive partition as well as Local disk C:\ and activation file save in virtual drive instead of real C drive in windows 7. But there is no file path option to save the activation. Its by default save on C:\documents and setting\all user\shared documents\rockwell\activation\***** Please help me how i activate my product in windows XP mode successfully? Thanking you. i will remain Regards -
HI, there. I am new to the Honeywell PLC, usually dealing with AB or Omron. Need some help from the Honeywell PLC gurus, my the only one PLC IPC620-1536 , suddenly stop working. No "Run" light or any outputs are present. Turning the "Mode Key" to the "program mode" and back to the "run mode" doesn't make any difference. I attached couple photo. My question, is any other way to start PLC running again? If I purchase the Win.Loader and communication cable and connect to the PLC, can I change PLC back to "Run" mode and upload the program, or fail to change the Mode using the Key. means the same fail using the software? Please update. Thanks for advance,
-
Hi! I have my 1756 IF8 wired in high speed differential mode but i can't configure the RTS smaller than 11 ms. What I understand it should be possible to set as low as 5 ms if module filter setting is 1000 Hz. Is there anything else that i have to do?
-
Hi, I keep getting an error that project is in binary mode and plc is in BCD mode. Wont let me change either. I must be trying in the wrong place...please point me to where i can change this in the PLC. I am getting an error in my RXDU with a Honeywell barcode reader, on one machine, I am thinking it is related. thanks for any help.
-
Hi guys! Im new in using PLC and im using CPM1A, is there a way setup the plc to run mode immediately after rebooting it, also even without connecting it to PC or handheld device? I saw in the manual "Startup Operating Module" but i am lost, i dont know how to configure it. Thanks for your advice.
-
PAROCK1 for HMI/SCADA View File Now a software solution is available for your Modbus (MB) needs in Rockwell/Allen-Bradley Control Logix or Compact Logix (Clgx) family processors, instead of a traditional 3rd party hardware like Prosoft MVI-56, Molex SST-SR4-CLX-RLL etc. It is an Add-on instruction (AOI) for PLC/PAC firmware v16 or later, (other solutions are available for pre v16 systems). For hardware interface, use PLC’s channel 0 (serial) or TCP/IP Interface module(s) to have as many MB TCP/IP devices or serial devices. (Some limits apply based on system configurations, Comm. settings depending on HW used.) Connect any MB Client/Master or Server/Slave device(s) to your CLgx PLC, including flow computers, analyzers, VFDs, Power Monitors, Level gauges, Smart I/O, etc. All the MB public/native function codes are supported. 32-Bit integers/floats as single entity are supported with byte and word level swapping. A separate utility automates the data mapping to your PLC logic. Features -Serial Master (BASIC required Option); TCP; Slave; Redundancy; More than 5000 accumulative registers; MB CFC (Custom/Private Function Code) Support; Data mapping too – Between PAROCK1 & your PLC logic; Packaged with Rockwell; TCP/IP Interface Module; Volume Discounts; Annual Support Requirements -Rockwell/AB-CLgx processor with v16 or later. Contact PCI for earlier versions. -If using CPU’s Chan0, you cannot use Chan0 for any other user mode activity. You can use it for non-user mode activities -TCP/IP Interface Modules from Rockwell/AB supported, are: -1756-EN2xx ControlLogix® Ethernet/IP communication modules, firmware revision 5.007 or later -1756-EWEB ControlLogix Ethernet/IP web server module, firmware revision 4.006 or later -1768-EWEB CompactLogix Ethernet/IP web server module, firmware revision 1.002 or later -1769-L30ER, 1769-L30ERM, 1769-L30ER-NSE, 1769-L33ER, 1769-L33ERM, and 1769-L36ERM CompactLogix controllers, firmware revision 20.011 or later -1769-L24ER-QB1B, 1769-L24ER-QBFC1B, 1769-L27ERM-QBFC1B CompactLogix controllers, firmware revision 20.011 or later -1769-L16ER, 1769-L18ER, 1769-L18ERM CompactLogix controllers, firmware revision 20.011 or later Other Related Services/Items -Custom PLC Add-on instructions building -PLC upgrades, troubleshooting, applications -PC Windows, iOS5, Linux, Mobile devices Comm. Drivers -Custom development, Technology Transfer Services -Other Non-AB communication drivers for serial or TCP -Full control system integration, training, architecture design This driver can be conviniently used with Visual Studio in development of complete large scale complex HMI/SCADA Systems. It can be used to perform advanced reporting MES, analytics, IoT, Big data type apps. One example is available to download here For More Info Overview of Parijat Drivers: Click here Additional supporting Info about Parijat Drivers:Click here Complete Related Driver options: Click here Submitter Scadadoctor Submitted 03/10/16 Category Other PLC Demo Software
