Search the Community

Showing results for tags 'Kinetix Servo'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Found 133 results

  1. HELLO EVERYONE THERE IS THIS PROJECT WHERE I CHANGED THE OLD SERVO SETUP WITH NEW SERVO DRIVE MRJ4200A-RJ SERIES. OLD SERVO HAS A REVOLUTION OF 15 BITS BUT NEW SERVO HAS 22 BITS RESOLUTION. PROGRAMMING IS SAME BUT MY DISTANCE CALCULATION IS DIFFERENT NOW AND MACHINE DOES NOT GIVE CORRECT DISTANCE. PLEASE HELP ME
  2. servo training

    Hello . Does anyone from the forum have such a program as on flimik, and he could share a program for f3x and the got1000 panel regards
  3. Hi there I am working on a project where Omron servo drags a part to a certain position using belt mechanism, But to avoid any slippage we decided to put an external encoder directly on the part. I was wondering what is the best to approach to drive the servo using the position of this external encoder. Is there any way that it can be configured directly with the servo? I am fairly new to coordinated motions, any help will be appreciated. Thanks
  4. I'm sure many of you are in the same boat with supply issues and elongating lead times with the Logix 5500 and 5700 servo drives. Are there any decent alternatives that are easily integrated into a 5380 controlled system, maybe with an AOI? I've looked at Beckoff and Parker systems, but Parker only seem to line CoDeSys as far as I can tell. Do any of you clever clogs have any suggestions for a well stocked alternative? As a side note, I'm not new to PLC programming, but I am only 6 months in to using motion and servo systems so be kind :)
  5. Hello! I'm trying to connect my QD75M2 with a MR-J2S40B1 Servo amplifier with an SSCNET cable. The problem is when I try to turn on the Servo ON/OFF on the Intelligent function in GxWorks2, an error occurs saying the servo amplifier is disconnected with my QD75M2. I'm confident that I've wired it properly. What could be the problem? Hoping you might help. Thank you.
  6. Is it possible to reset " Motor replacement detected error" ( Error code 95.01) using code without connecting to PLC through sysmac studio? If yes please suggest how to do it... Thanks in advance...
  7. All of the ethercat servos I have installed are Omron. I have used many many brands in the past - over analog, pulse train, but not ethercat. I have one of the Yaskawa servopacks that can control two servos independently. The drive is all wired (POT, NOT, safety), autotuned, it's in RUN OK state, I have installed the ESI file, set up the axis, mapped the PDOs.. it's all working, but they do not move. I made a test program just with MC_POWER and MC_MOVEJOG/MC_MOVERELATIVE/MC_MOVEABSOLUTE along with the resetting of MC and EC and the servos do turn on, but ignore any movement command. They do not flare up with an error, and they give me their actual position, so the network is working. If I send the movement command the command position starts to differ, so the plc is/should be sending the command. I feel like there's something missing in the PDO mapping screen, but I didn't need to do all of this with Omron so I have no idea. I thought at first the servos needed huge units of movement and speed but the actual position value confirms this is not the case since it doesn't ever change.
  8.  What is the difference between Active Immediate homing and passive immediate homing ?   Does Motion servo axis have to be turned ON for active immediate and turned OFF for passive immediate homing ?.
  9. I have seen some programs in which they manually unlatch all bits like in figure 1, and in some programs they don't do that.  The instruction help page, ladder execution says that in pre-scan .EN, .DN, .ER, .IT bits are cleared to false So do we need to unlatch all these bits before giving a motion command like MAM ?  
  10. We currently have Delta DVP60ES2 and DVP32ES3 PLC's doing positioning control on Inovance IS 620PS2R8I 400w Servo Drives by Pulse/Direction. Under both of these environments our pulse count read on the Inovance drives are reading higher than what the PLC is outputting. We also have Mitsubishi & Inovance PLCs, which when connected to the same Inovance drives dont have any discrepancies in the pulse count. We also have Delta ASDA servo drives, which when connected to the Delta DVP PLC's also don't have any discrepancies. Given we have tested these combinations, it has led us to believe there is something unique about the pulse train output from the DVP PLC's that is causing the Inovance drives to read additional pulses. Has anyone experinced a similar issue with Delta PLC pulse output? If so what was the solution? 
  11. Hello everyone, I have this weird problem that the PC (process complete) bit of MAS command does not clear after a cycle time.  As you may probably see in the picture attached when the desired torque has been reached, the servo has to be stopped using MAS command; however, this is good only for one cycle!! The PC bit will remain on even when the whole sequence gets unlatched/reset. I have to manually reset this bit. I was wondering if you could help me with this issue, please?  Thank you!  
  12. Hi guys,  Can someone explain me what is the difference between SS1 and SS2 instruction ? I read the help but its not so helpful for me.  THank you so much.
  13. Hi,  Can someon help me with the following question. Like what makes a Kinetix 6000 drive a Guarded drive ? What type of safety stuff can you set to make it more safe.  Is it some parameter ? I am bit confused, by the manual. Should I active it in the PLC program or how ? Or it is some setting like a safe speed or torque.  I would really appreciate any help. Thank you so much ahead.  Have a great day, thanks for the reading.
  14. Hello guys!  Im using RS Logix 5000.  Can someone explain me what is the difference between when a servo is shutdown or disabled ?  I read the help but it says the same. I can assume it like when its shutdown, there is inside some circuit which is not allow the 3 phase for the drive.  Disabled is that when it have the 3 phase but nothing can happen ? Is there any difference with the break ? Like when its shutdown it can rotate until its slow down by itself or the break will be active ?  I tried to uplod a pic but it was not succesful. When you open a servo axis properties and you choose the Fault actions tab. You can find there these settings.    Thanks a lot. 
  15. Hello Guys! I have couple of questions about tuning an ab servo motor. -Actually what does the drive or plc doing when I launch a servo auto tuning?  - What are the little boxes like position error integrator ? There are checkmarks in fornt of the lines. Can I choose the methode or something? I mean its not "auto" ? Why it is auto then ? - Can someone send me some basic literature where they explain me what these stuff acutally meaning ?  - What is the hook up test what for is good ?  -When you are doing a servo auto tune what are the parameters that you are monitoring and why ?  -I should do the auto without or with load ? Whats the difference ? I know there are so many question I would be so grateful if someone could help me with these answears, or even just with one. Thanks again. 
  16. Hi. I would like to ask that like you guys are when using a kinetix servo motor what type of safety conditions are possible ? I found a fault actions label. Is there anything else like between the parameters or so ? Thanks ahead. 
  17. Good morning guys,  in your experience what is the best way to syncrhonize a motor controlled in speed with an inverter and a motor controlled in position with a servo drive? Let me explaine better what is my situation: I have a belt running normally at a certain constant speed. in some moments, I would like to syncrhonize the speed according to an axis controlled from a servo. the command of a servo specific position target and of course speed and acceleration e deceleration rate. I would like to adjust the belt speed in way to follow as accurately as possible the servo movement. Thanks a lot Andrea    
  18. Hi all, I'm having an issue with one of the Kinetix6000 allen bradley servo drives on a filling line that I support. This particular servo motors controls the rotary movements of a series of pumps to ensure accurate dose timing. Every time that I start up the machine, the PLC (Controllogix L7 firmware v28) executes a homing sequence to ensure the servo finds its 0 point. However, the servo in question keeps getting an 'Overspeed Fault' (E55). So far in troubleshooting, we've basically changed every component. We replaced the drive, feedback cable to the drive, and even hooked up a new free-spinning motor directly to the drive. Every component change has resulted in the same Overspeed error shortly after the homing sequence starts. To try and rule out a mechanical issue, I even disabled the homing sequence in the PLC and tried to move the motor using Motion Direct Commands. Immediately after a MSO command, the drive faults out for OverSpeed even with no motion. The last bit of troubleshooting we swapped the position of two of the drives, but the same OverSpeed fault happened on the drive connected to the rotary movement motor. At this point, I'm even considering changing the sercos fibers and the Kinetix power rack. Has anyone experienced anything like this before, or have advice on what to try to make it work? Thanks in advance for all your help  
  19. So I'm new to the automation scene and in my training I decided to setup a little test rig, plc, drive, servo, sensor, hmi...etc.  Everything is wired and hooked up. What I'm trying to do is simply get the servo to spin. here is a screenshot showing what I have. I think there are some flags on the servo itself that need to be set but I'm not sure how to do that. In Base(x) I have tried 0, 1, 4, 5, 35. Any help would be appreciated.
  20. CHANGE position MR-J3

    hi I want to change a position of a servo (MR-J3-350T) which displays as current value 9500 to zero. how I can do it with MR-Configurator. in which menu should I go? thanks
  21. reset position MR-J3

    hi I want to change a position of a servo (MR-J3-350T) which displays as current value 9500 to zero. how I can do it with MR-Configurator. in which menu should I go? thanks
  22. home postion servo J3

    Hi, I have a Mitsubishi Servo motor with its amplifier MR-J3-350T. I lose the home position. How can I set the value of the position to zero if I detect a home detector. I use gx developer. thank you
  23. Hi, I am quite newbie in the PLC world but I got my hand on a Kinetix 5500 (model 2198-Hxxx-ERS2) with a VPL-A0631E-C motor. I also have a CompactGuard logix 5380 to program it. I am doing a "for fun" project to experiment and learn how the devices work.  My first question is about power wiring. In my understanding from the manual, the Kinetix 5500 main power can be configured as three-phase or single phase (Using the L1, L2, L3, GND connector - think is called IPD). In my home I have a classic 220V (EU) socket. Is there a way to connect the Kinetix directly to my socket? I tried a few random stuff like L1 -> L , L2 -> N or L1 -> N , L3 -> L,  (GND -> GND) but every time the circuit would break. (Actually, I had one lucky attempted where the circuit did not fail with  L1 -> L , L2 -> N, and I managed to operate the motor, but when I reconnected it again it failed. Am quite buffled about the issue here. I am using a socket splitter if that something to comment on.) The second question is about purchasing an actuator. I found many interesting stuff like index tables or linear actuators. I requested a few quotes from some vendors but the price range they provided is a bit off budget for me (the majority was more than 2k). I am looking for some thing to attach to the motor in a price range of 1k - 1.5k. Do you have any suggestions for me? There are no load requirements. I just need to have a moving part so that I can for example put a barcode sticker on it and change the behaviour reading on that. I could attach something handmade but I am willing to put something extra to buy commercial equipment. As I am new to this, feel free to comment any inaccuracies or misconceptions. Happy to learn.
  24. QD75M4 AND MR-J2S-40B

    Hello i have problem about connection between QD75M4 AND MR-J2S-40B  now MR-j2S is display "Ab" every time i can't solve this problem 
  25. I am looking for how others have set up vertical axis motions using the Kinetix 5700 servo system. I have a 2 axis pick/place unit with a horizontal axis (X @ 2500mm) and vertical axis (Z @ 1200mm) that works as designed during normal operation. X axis has no holding brake and Z axis has a factory installed 24vdc to unlock brake. There is a GuardLogix L81ES control system that handles the safety and control. On pressing E-stop/opening Gates the vertical axis will stop the motion, apply the brake and hold with no problems. (2198-D032-ERS3 Drive, 2198-P031 Bus Power, MPL-B430P-MJ72AA X Axis, MPL-B330P-MJ74AA Z axis) The issue that I ran into was an accidental download of the program without activating the e-stop and the vertical axis dropped unexpectedly when entering program mode on the processor. I am aware that this instance was my fault as the programmer, however I am also concerned that this might occur again in the future if the controller ever enters fault mode or someone else completes a download. I have done some investigation with the "ProgrammedStopMode" parameter on this single motion axis and attempted all 5 options and the vertical axis still has a free fall drop for a second before the brake grabs hold - so evidently this is not working for me. (Page 24 of Vertical Load/Holding Brake manual - https://literature.rockwellautomatio...t003_-en-p.pdf) I am curious if there needs to be something done elsewhere as the X and Z axis are set up as coordinated axis? I also am unaware if I need to preform some action/parameter with the bus power supply for this? The current state of the machine as it sits now is preforming a MSF in manual mode after 5 seconds of inactivity or 30 seconds in auto mode. This axis is usually in demand every ~22 seconds. This will shut down the axis after preforming a brake test on the vertical load and seems to function OK, however it is still in the back of my mind the issues mentioned previously if we ever enter a controller fault while indexing. Thanks for your insight