Search the Community

Showing results for tags ' technology transfer services -other non-ab communication drivers for serial or tcp -full control system integration'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Found 296 results

  1. InTouch Comms

    Hi Everyone, I've just installed InTouch V10 and am trying to develop communication with Emulate5000, for educational purposes. I looked over the internet and found some videos on how to develop communications by setting up the topic name and node name in DA Server manager, but the issue I'm facing is that my SMC only shows logViewer and nothing else (snapshot attached). Am I missing some vital component or dirver? Or is there some problem with my installation? Help would be much appreciated.   P.S: Window Maker and Viewer are working fine. Thanks, Sabih
  2. HI All,  I have an issue with my SCU32 communication.  Back ground Two SCU32s  (top and bottom side) connected via a 1100M datacable  using port1 ( 9600bps,  8-2-E, start code FF, end code FE, Tx save to d1000-d1200 , Rx save to d2000-d2200). PORT2 of bottom SCU32 is connected to a compass( 2 wire, 8-1-N, 19200 bps, serial gateway MODBUS ). Refer to photo Issue  Without compass, the receiving data at top is very stable and is didn't see any fluctuation. But if is compass is connected at bottom side port2, there is a fluctuation at the top side RX data(specifically d2000-d2005 ) .  I checked the data a bottom side TX (d1000-d1200) and it is stable. Only after sending the data and Receiving at Top side, then only the starting words fluctuate. I am not sure sure what is wrong, I am using logical ports for the DTXDU/DRXDU and compass.   Appreciate all your feedback and suggestions.  
  3. PC to PLC Kommunikation

    Hello, i want to connect my PC to the PLC(RSLogix5561)  over TCP/IP. In rslinx the Ethernet driver are configured. My PLC IP Adresse is 192.168.1.100 and my PC Adresse is 192.168.1.105. From my PC i can successfully ping the PLC IP Adresse, but from the PLC i can't see my PC. And it does'nt schow in RSlinx. Is there anything i am missing?
  4. Hello there, I am new to OMRON so need some help to communicate two PLC over FINS.   Here are the description of the system... (IO Table image is attached)   PLC1-  CJ2M-CPU33 IP- 10.113.218.34 SUBNET-255.254.0.0 UNIT NO - 00 (set the dial available on the CPU in HEX) NODE - 22 (set the 2 dials available on the CPU in HEX) PLC2-  CJ2M-CPU33 IP- 10.113.218.35 SUBNET-255.254.0.0 UNIT NO - 01 (set the dial available on the CPU in HEX) NODE - 23 (set the 2 dials available on the CPU in HEX)     Now, what i have to do is to transfer the D100 to D110 from PLC1 to PLC2's D200 to D210 and Transfer the D100 to D110 from PLC2 to PLC1's D200 to 210.   I have tried RECV and ECHRD blocks but didn't succeed yet.   Two CPU are connected over ethernet via a industrial switch.   Can you help me to achieve data transmission please...
  5. Hi All need to convert a Decimal Value into Ascii code to send out on serial 485. eg. Weight comes in as Int 12345 i need to send it out in Ascii as 23 32 20 31 32 33 34 35. I have created an array 0 of 8 (Word) DB. Is there an easy way split the int into Digits convet in into HEX and slot the value into the various array positions? Array 0 of 8 = 23 means # Array 1 of 8 = 32 means 2 (Station ID) Array 2 of 8 = 20 means Space Array 3 of 8 = 31 means 1 Array 4 of 8  = 32 means 2 Array 5 of 8 = 33 means 3 Array 6 of 8 = 34 means 4 Array 7 of 8 = 35 means 5 Array 8 of 8 = D means CR    this sends the value of 12345 to Display ID 2 . need help to convert the decimal number in ascii. the decimal number will be max of 5 digits and less than 32000   any help will be greatly appreciated.
  6. friends, forgive me for my english.  I have a problem.  omron nt620c panel cannot access the system menu.  I reinstalled the system program through NT-SYSTEM INSTALLER.  after which I get the message: no direct information is set !!!  please use the support tool to set the pt control area and the pt notify area.  go to the system menu does not work.  I swing the corners of the screen as described in the manual.  from a video from YouTube I realized that there should be a message connecting to host
  7. Hey everyone, I have a CJ1M PLC with a CJ1W-SCU21-V1 serial card. It is unit 6 and I am using port 1. I have bit 1659.06 ((1500 + 25 * Unit #) +9, bit 6) as "characters in buffer" but it never comes on (data is being received through the port successfully). It is on No-Protocol mode. Does anyone have any ideas as to how I can detect data in the buffer?
  8. HMI and PLC Communication problem

    hi there. .. i am new to plc programming.. Right now i am having problem related to communication between hmi and plc.. i have HMI WEintek 6070ip and plc mitsubishi FX2n.. i have written a program in gx developer . and communicate it with EASY Builder for HMI. so for now plc is communicating with my program written for hmi on pc. but when i downlaod to hmi and connect plc cable to hmi then hmi shows no plc communication. i am having a problem for communication between hmi and plc. any help will be a life saver. thanks in advance
  9. Serial comm with FX1N PLC

    I need to communicate with a Mitsubishi PLC using Matlab. To do that, I open a serial communication with the appropiate parameters (7,e,1,9600), and write an ASCII message based on the manual I have (attached). I have tried examples as the one in the attached image. The response starts with a 6, that is, the ASCII number for ACK, so something must be working. But the rest of the response is junk (149, 149, 149...), although its length depends on the input length (if I add terminator, the response is longer, and so on). I am completely stuck. Some information that might be helpful: I am using a Serial to USB converter that I have used successfully with other PLC (which used Modbus, so everything was easier) There's a VB application (of which I don't have the code) that is able to connect to the PLC (I need to connect directly without using this intermediate app). I have decompiled it trying to get some info, but was just able to confirm the 7,e,1,9600 parameters, since the rest of the code is too mangled to analyze The attached manual was sent to me by the guy who designed the PLC and its ladder code, so I guess it is the correct one I have tried the echo mode (TT) to no avail, response is always the same I have some doubts regarding the reading of a value (see attached image). Why is there a second message from the PC? Shouldn't I just need to read the response? GX Developer tells me that the address D8120 (which is supposed to define the comm format and protocol) contains a 0, which seems weird. Any help or hint would be greatly appreciated. Thanks jy992d69901e.pdf
  10. Hi everyone! I got this machine with a CP1H PLC and NS8-TV00B-V2 as PT. I was told that they were working fine, but suddenly, It appeared a communication issue: black screen and "connecting..." at right bottom. I dont know if It is a configuration problem or some hardware damage.  These are the configuration in the PT and the PLC. The communication is through RS232 Serial.  I tried to communicate another PT screen with the same communication settings and IT WORKED!. ' I've been thinking that, perhaps, the serial port A is damaged, I have tried to set port b, but I havent could. How can I configurate PORT B??   THANKS...  
  11. Hey all - I am working on a car wash system design that will utilize the Nayax payment system. Has anyone utilized them? How do I incorporate the device with PLC to automate the system. After payment is approved how can I send out that signal from them, all via ethernet on a managed switch w/ wifi for exterior comms for the Nayax.
  12. Constant Web Tension Control

    So I'm having trouble writing a FBD within my current program for a slitting line. I need to keep a constant tension on my web as it is being recoiled onto our recoiler. I wrote a simple program using a sensor to read the growing rate of the coil to get a radius and I have feedback on my torque on the recoiler motor. The simplest math for this application without getting into anything too fancy should be Tension(lbs)= Torque(ftlbs)/coil radius. only problem is when its less than a foot then my calculation is thrown off and it actually shows tension goes up until it reaches the one foot mark then it seems to scale correctly. Do I need to scale something else? Any help on this would be appreciated.
  13. Hi All, Hope you all doing well in this pandemic life.  I would need your expertise with an issue I have been struggling with for past few days and thought to reach out here. I am working on a migration project with GE PLC and Citect SCADA 7.10. The GE PLC is migrated to ControlLogix L74 Rev24.10 while Citect SCADA is retained. For testing I only have L71 and L82 and could not managed to organise L74. When the code the loaded in L71 and connected to Citect, I cannot see tags in Graphic page but I see the subscription.txt in Debug folder shows all tags good . The same code when loaded in L82, the Citect works instantly.  Does anyone know this behaviour of PLC and SCADA? Regards, DeeEngr    
  14. Sorry for my bad english speaking. I want to change the baud rate to 19200,38400,.... for send it via Programmer-Serial-Port. The software GX-Developer can do it!. When the PLC is switched on, we generate a value in the data register D8116 and D8117. GX Developer reads the PLC type and data registers D8116 and D8117 at startup and generates a value. This value is written in D8118 and D8119. The big question is: how is D8118 and D8119 generated ??
  15. Can someone please suggest a Control Panel Builder that is located in Germany?   I work for a company in Australia and due to Covid 19, we are struggling to meet an onsite date for a project in Germany.   This project uses Siemens PLC gear, Danfoss drives, and mostly Schneider electrical gear. The enclosures are custom and stainless steal.    I have electrical schematics and enclosure drawings for quoting.
  16. Mitsubishi Fx5uc

    hello everyone, Im new with mitsubishi and  ive got a project with a Fx5uc but im stucked in communication protocol to communicate with a weintek HMI ive already tested easybuilder simulation with a modbus tcp ip symulator and it works but im completlely lost about mitsubishi, is there a way to communicate via Modbus TCP/IP? or which protocol would u recommend as i have to connect 2 drives as well. thank you in advance
  17. Q selection tool

    colleagues, here I leave you an offline configured for the Q system greetings http://forums.mrplc.com/index.php?/files/file/1160-q-selection-tool/
  18. Q selection tool

    Version 1.0.0

    7 downloads

    Q_PLC_offline_termékkiválasztó_szoftver_-_MELSEC_Q_Series_Selection_Tool.zip
  19. Q selection tool View File Q_PLC_offline_termékkiválasztó_szoftver_-_MELSEC_Q_Series_Selection_Tool.zip Submitter javiermorales Submitted 04/18/20 Category Demo Software
  20. Mitsubishi FX5-4LC

    Hello Guys,                      can anyone help me programming of FX5-4LC temperature control module with FX-5U80MT PLC. I want to Read present temperature value of each channel and want to set Temperature Set value from PLC.
  21. Hello. I am working on a pilot project building an automated RV park. Our goal is to have people sign in online, or in person at a kiosk. Make their reservation, payment, and get their confirmation e-mail. In that e-mail, will be a QR, or Bar Code, that when scanned at the gate opens the gate, and starts a light that flashes at the site they rented. Power will then be turned on at that site, and a timer in the process will begin, based off their rental time. Once their time has expired, the power at the site will be turned off, controlled by a PLC, and relays.  So I am looking for help in all directions. I have some leads on some plug-ins for Wordpress that offer reservations, and other plug-ins that do Bar code production. As far as the web part I have that covered. We can generate a custom barcode, or QR code based on individual rentals and those can be sent to customers. So what I need is someone to help point me in the right direction of equipment that can speak between the online Barcode process and the PLC to allow a process to begin when scanned. Based off their rental parameters their power is turned on or off. Perhaps a SQL query in some form? I haven't used it, but am aware of its capabilities, and this does seem like an application where it would be used. Is there anything that you have used that are tried and true? I know it's a strange request, just hoping someone bites. Thanks in advance for any ideas, I look forward to solving this puzzle, one piece at a time. 
  22. Fatek PLC Communication Problem

    hy all. i am having an error while communicating with fatek plc. when i communicate it gives an error. " Com port open fail, plz check if this port is used by other programme when we online the PLC (Fatek/ WinProLadder). kindly Guide me   as it looks like port is already used by another program . and i dont know how to kill that program ..       
  23. Hi all, I've ran into an unusual situation where I could use some suggestions.  I have an AB PLC working in the field, and an existing fixture that needs to be transferred from an Omron PLC into our AB.  I have an integrator who did some offline development with a welder that uses Anybus communication.  He sent a .ACD file to implement the logic from.  The file has an Ethernet module configured but more importantly, it's showing EDS not registered.  I've asked for the EDS he used, and none of them work when trying to register it via right-click and register.  I can export the module, but it won't import into the current PLC program because there's no EDS (shows EDS error after the import).  If I try to take the program that was sent to me online with the PLC, it will automatically upload and overwrite the build.  I can't even open the properties of the module to see what the integrator did. The end goal is to have the offline developed module implemented into the current program, but it seems like everything I've tried to do has me against a wall.  Is there a way to go online without uploading?  Maybe there's a way to implement this I haven't learned yet?  Any suggestions would be much appreciated, and if more information is needed, I'll be glad to provide it. More info:    PLC Type: 1756-L82E ControlLogix 5580    Rev: 30.014    Studio 5000 Version 30.01.00 - Standard Thanks, K
  24. Hello guys, I am very new at this. I am trying to make a Schneider PLC (TM251MESE) to send some serial commands (485)  to a integrated stepper motor from Automation Direct (STR-MTRD-17030RE, but I am lost. The driver has been program to receive the SCL commands. But not quite sure how to send those from the plc. Im using SoMachine V 4.2 Have any of you done anything similar? Any example will be greatly appreciated.  Thanks 
  25. INFO

    Dear sir, I am working in container terminal, we have Siemens plc  s7-300 , Bromma spreader with SCS-3( codesys software) spreader field device sensor (ifm) connected to slave ifm CR9011, now a days we are facing too much issues in scs-3 so we planned for isolate the SCS-3 but we want to know ifm module Cr9011 how to communicate to Siemens plc  7 how to write in hardware configuration. can you please suggest us.