Search the Community
Showing results for tags ' subnet and gateway. any remedies/advice is most welcome. please provide a guide on the communication/configuration setup. thanks'.
Found 242 results
-
Dear sir, I am working in container terminal, we have Siemens plc s7-300 , Bromma spreader with SCS-3( codesys software) spreader field device sensor (ifm) connected to slave ifm CR9011, now a days we are facing too much issues in scs-3 so we planned for isolate the SCS-3 but we want to know ifm module Cr9011 how to communicate to Siemens plc 7 how to write in hardware configuration. can you please suggest us.
-
How can I determine if both my Produced and Consumed tags are communicating with each other, and if have the right set of tags since I forgot how I named them? Is there a way to confirm that both my P & C are communicating.
-
how to read ip port status of any other third party device like IPC
nildazzler posted a topic in Allen Bradley / Rockwell Automation
I have IPC and need to detect status of IPC and PLC communication . I need help with the same that how can in detect it ? Is it possible with message instruction ? if it is then how ? -
Hi! I am using a Ethernet/IP and a Brainbox ED-588 as a gateway to a PLC that has 8 in and 8 out Digital IOs. In order to interface with other types of PLCs I am looking for a gateway that has 16in and 16out digital I/Os I have also been asked to work with NPN output, not PNP. This can be achieved using yet another component, but if possible I would like the gateway to be configurable with NPN/PNP output. N.B. The orignial protocol doesn't even have to be Ethernet/IP, I might be able to work with other protocols as the source. Products that I found do not have enough IOs Thanks!
-
Can anyone help me with the issue in the picture? We have the correct version in place yet it gives me a version error stating it needs the version that is installed. Doc1.docx
-
Hello, My previous topic was want to establish communication CP1E --> Videojeet Printer using RS232 serial cable. this project test SUCCESS. by the way distance from printer and PLC was very far almost 500meter. so printer technical team request to use tcp communication using cat5e cable. Problem: 1. I'm using TCP communication protocol that need me to have open,send,receive,close port. 2. Communication testing with PC Hyper Terminal --> OK but HT need in waiting call mode, i don't know why. 3. Using printer no result show. how i'm suppose to know communication already establish? 4. Communication setting on PLC Setting-Built in Enthernet need to add other communication device.? here i'm share some programs to give more understanding. Thanksm TCP with printer.cxp
-
RS 232C Serial Communication between Magelis HMIGXU3512 and Omron PLC CP1E
Klauzer posted a topic in CX-Programmer
Hello. I am trying to make a serial RS 232C connection between Schneider Magelis HMIGXU3512 and Omron PLC CP1E. However, there seems to be a communication problems between both of the equipment. I am using cable XBT Z9740 for the serial communication cable. The format used is 8.2.N for both equipment. The baud rate is 115200. No Flow Rate is choose. Anyone can help with this kind of problems? -
MicroLogix 1100 and In-Sight Cognex DM300 series commumication
Josemarian posted a topic in Allen Bradley / Rockwell Automation
Hi All, Am trying to communicate and make In-Sight bar code reader to trigger through MicroLogix 1100 with RSLogix 500. Does any have any info as to the steps to follow. Most of the info I saw and have tried were for SLC processor In fact, I created the String file ST10:0 for the target device as was mentioned in one of the posts but when I complied it there was error saying that St10:0 was not supported by the module. Please see attached file. Any insight will be appreciated -
IN TIA Portal V13 HMI Alarm Setup, Discrete Alarm Not allowing Bool Tags in "Tag Trigger". Please help how to set Bool Alarms?
-
1734 Vhsc24 very high speed counter module
Raghvendra posted a topic in Allen Bradley / Rockwell Automation
Hello, I want to compare pulsed coming from flow meter with a constant value. And make a bit to high level when my set pulses are equal to present value in counter. I am using 1734 Vhsc24 module for this. If any body have sample program kindly attach it. -
Hi everybody, Is it possible to send MELSEC commands to oneself, locally, not using the phiysical ports? I would like to use some commands described in the "Communication_Protocol_Reference_Manual_(MELSEC)" to get some self-management functions in my PLC. For example, in OMRON this is possible using CMND instruction and setting the FINS address to 0.0.0 in the parameters of the instruction. Thank you very much.
-
Dear Experts, I want a sample block to find out the status of my Profinet cable w.r.t Hardware configuration. whether the cable is connected or disconnected from the node. Either my nodes may be VFD, HMI, SCALANCE, etc... please share the sample blocks... S/W ===== >Tia portal v14 sp1 update 6 H/W ===== >CPU 1214C DC/DC/RLY hanks in advance
-
Connecting Generic I/O module to Micrologix 1100
Josemarian posted a topic in Allen Bradley / Rockwell Automation
Hello All, Am a bit new to practical PLC applications. I was trying to configure a Phoenix Contact I/O module (1452916) on a MicroLogix 1100 PLC but it kept faulting out with the fault light RED. It would say "Major Error Halt S:1/13". The error description says I/O mismatch. The error code is 187h (see attachment). The Phoenix module has a cable with 19 pin positions for the 8 input. I connected the pin 17 and 18 to 24 volts and 0 volts respectively. Then because I was using input 5 I connected the pink wire to PLC input (I/1) 24volts and the White/Yellow wire to the PLC common. On the I/O configuration on RSLogix 500, I used "Other" ( See attachment) but did not know the vendor details. Could anyone help me with the steps on how to communicate with the module? I have also attached the PLC program I was running. Thanks -
Hello, I have been so many days trying to comunicate the multiway software trought a serial usb converter with the SCU31 device, using a omron function block to read a holding register, but I can't achieved it. Now Im receiving some frames on multiway, but there is always some errors. I was wondering if somebody in here that have worked previously with modbus and omron can be able to help me in how to configure everything corectly to be able to read the value from multiway, on the plc, and where is this value saved. I'll upload some captures to show what I have done till now.
-
Hi Im hoping someone can help me out! i have a PLC SLC 5/03 and i want to connect the DB9 port with DH485 protocol to a computer 100 fts from there, is there any problem with the distance? and what kind of cable should i use , i already connected with my laptop with a USB-serial with a null modem cable RS232 (i did the cable by my self) but for the distance i cannot keep using that protocol so what is the recommendation?
-
I have Mitsubishi FX-1N P.l.c i found a problem about communication port.Run and Power L.E.D on as per routeen but i cant communication with GX.Works 2. PLz tel me how can i fixit this problm....
-
Hello, I currently have two IC220PNS001 connected to IC695PNC001. The PLC being used is IC695CPE330. Out of the two PNS001, one of them has a solid SF Red light on which means bus error according to the Status Parameter IO. I disconnect every single IC220 card connected and downloaded the whole configuration but I still have a Bus error. PS: I have also tried to switch the PNS001 with the brand new out of the box and I still have the same error. In the manual, it says Profinet Diagnostic available, can somebody please guide me as to where I can find the Profinet Diagnostic, also is there any manual for PNS001 which explains the in-depth debugging process for this PROFINET Controller.
-
Hi new to the forum, and first post, however, I have found an abundance of great information here, so I was hoping someone might able to help me with an issue. PLC is BRX BX-DME1-10ED13-D I am trying to read an analog output from a sensor that is capable of essentially outputting a mA signal proportional to where a printed line, or contrasting edge is at in its field of view. It is used for web guiding applications to make sure the web is tracking straight, so you can identify if the line or edge is moving to one direction or the other, and correct the web with an articulating web guide. I have attached the diagram for the sensor, but I cannot for the life of me figure out 2 things 1) The power supply to the sensor is listed as follows Supply current - From fife control +/- 12vdc 50ma (+)12vdc AND - 40ma (- )12vdc how do you provide both (+) and( -) 12VDC for the supply power to a sensor- 2 power supplies with the the opposite polarities grounded on each? 2) The outputs are listed as "Sum" and "Differential" so apparently there are two outputs, i dont know if anyone has come across these terms relative to sensors before, but I am trying to sort these out. According to the OEM Sensor Output Range -20 mA to +20 mA for line guiding -20 mA to +10 mA for edge Guiding I have attached the pin out diagram as well as the sensor spec sheet, but I am curious to see if anyone might have insight as to how I would get an analog input reading from this configuration? Thank you in advance for any help! 224615.pdf SE-26B Product Sheet.pdf
-
Dear Experts, I want a sample block to find out the status of my Profinet cable w.r.t Hardware configuration. whether the cable is connected or disconnected from the node. Either my nodes may be VFD, HMI, SCALANCE, etc... please share the sample blocks... S/W ===== >Tia portal v14 sp1 update 6 H/W ===== >CPU 1214C DC/DC/RLY hanks in advance
-
Some videos training PLC AB(Rockwell) RSLogix5000
hochiminh2019 posted a topic in For Sale, Employment, Services or Wanted
Here are some videos training PLC AB(Rockwell) RSLogix5000 I hope this helping someones! 1) Setup RSLink to connect PLC using a USB cable https://www.youtube.com/watch?v=mk-wgnwO4E82) How to set up hardware involve Input/Output, Analog, Device Net... PLC AB(Rockwell) RSLogix5000https://www.youtube.com/watch?v=pIUNPCEcNn03) How to use timer/counter/Compare PLC AB(Rockwell) RSLogix5000https://www.youtube.com/watch?v=7BDzAoFBJPMhttps://www.youtube.com/watch?v=EM3KO8JSYsMhttps://www.youtube.com/watch?v=yQtrIhTmwqA4) How to use Analog PLC AB(Rockwell) RSLogix5000https://www.youtube.com/watch?v=8raR0f7zr6M5) How to use RealTime-Clock PLC AB(RockWell) RSLogix5000https://www.youtube.com/watch?v=Lgg8hjs5jkY -
Communicating between plc's with different IP's
plcaholic posted a topic in Allen Bradley / Rockwell Automation
I am trying to get produced and consumed tags set up between 2 1756 racks with different ip's. The 1st rack has an ip address 172.28.6.3. The 2nd rack has an ip address of 10.81.105.8. Would this be as simple as adding an EN2T card to one of the racks and setting the ip of one onto the same network? Or is there a better way to do this? -
Hello , I dont have experience with Mitsubishi PLC. I want to do a modification on the ethernet configuration but i dont have the source code . According the information that i read we can use GX IEC developer or GX developer but my question are : Can i upload and download the program with GX developer? Even if was previous developed with GX IEC Developer i will not do any change on the code only on ethernet configurations , add a MC communication. I have another concern about the profibus module. For the profibus is necessary another program right ? But if i don't want do any modification on the profibus is dont need it, right? My experience on Siemens when is necessary do a modification on the hardware configuration. I should have all the hadware configuration " right" it means if i have profibus i should have the right GSD to allow do modification on the configuration . But on Mitsubish i can´t understand that well . Regards Roberto Fonte
-
We have an old press using a Series 90-30 with a 311 CPU 5 Slot Rack. I am trying to pull the program off so we can convert it to a new CompactLogix. I am using Proficy ME v6.0. I have the proper RS232-485 cable and a built in serial port on my XP laptop but cannot get it to connect. I know that Logicmaster projects cannot be opened by Proficy ME and being such an old 90-30 it probably was programmed using Logicmaster. Would being programmed by Logicmaster prevent me from even being able to communicate via serial connection?
-
Gentlemen, I'm new to Siemens and now working on a project for my client. I have a S7 1241 cpu, CM1243-5 com module, a KTP700 hmi prifibus dp. The hmi is connected to the CM1243-5 via profibus cable. My problem: I'm not able to detect the hmi. My plc is connected to my router and I'm able to get online with it. I've attached some diagrams..just in case. Appreciate any help. thanks, Moorthy.
-
Hi all, i just need to clarify that can we use GTSoftGOT2000 to work with QnACPU. i am describing my situation below. We have a vendor asking asking us to install a Large Screen where a operator can see the images of the faulty parts with respective of what part they run(we run almost 14 parts on one machine). the largest HMI that i was able to find was a 19inch one from Pro-Face, but thats not sufficient . so got and idea of using GTSoftGOT2000 and create a HMI screen and connect it to a PC Moniter.
