Search the Community

Showing results for tags '#mitsubishi #servo'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Found 404 results

  1. Hi all. I am new to Autonics and Mitsubishi. I am trying to read and write the data of an Autonics TK series temperature controller using RS-485 with QJ71C24N-R4 coupled with Q00UCPU. I have the hardware setup as attached images. Software setup are as follows:  TK4 Settings: Communication address: 01-99 Communication speed: 38400bps Communication parity bit: none Communication stop bit: 2 Communication Response waiting time: 20 Communication write: Enable Mitsubishi Intelligent Function Module: CH2: Operating: Independent Data Bits: 8 Parity Bit: None Even/Odd parity: Odd Stop bit: 2 Sum Check code: None Online Change: Enable Setting Modifications: Enable Communication Rate Settings: 38400bps Communication Protocol Settings: Predefined protocol Task to be carried out: 1. Read SV 2. Read PV 3. Write SV I have the address for the modules but I am not sure how to communicate or the program which allows to reading/writing. I had tried to follow the attached PDF but i cant key in the first line as there is a bit with "G450" which has an error stating "the device No. is over usable range" and  "An unusable device has be designated". I hope someone here could guide me in writing the program, or any reference for me to follow.  TK-Q02H_RS485_EN_Technical_support_180823_W.pdf
  2. Hi! We have a GOT2000 HMI with a Q06UDVCPU system. During an investigation, I found that the address on the HMI (for example D10120) and the address in the PLC (D10020) are different. The value is the same, it appeared instantly during monitoring, but when I searched for it, didn't find it (I couldn't find the D10120 in GxWorks2, and couldn't find D10020 in GtDesigner3). The HMI's address is 100 higher. I never saw anything like that. Where is this difference can be set? Knowing this, I can navigate in the program..it's just annoying.
  3. How can i limit MRJ4 servo load?

    Hello, I am beginner at servo and its driver. i am using MRJ4A driver and HG SR102 servo motor. i want to make my servo stop or alarm when the load is over the maximum load that i set by my self. what parameter should i set to limiting servo load even if the servo motor strength enough to lift the load.?  
  4. Simulation of FX5 in GX Works3.

    Hello gentlemen. I am working in a company that makes SCADA software, and needed to do reading/writing tests on MitsubishiPLC's, In this case I needed to do tests on FX2, FX3 and FX5. I saw that Mitsubishi makes available the GXWorks 3 software that is possible to do simulations of FX5 and FX5u in it, but I can't connect in any way to the PLC being simulated on the company network. I put the correct IP in the ModuleParameter\EthernetPort configurations, I write a simple read/write program in ladder, and I use Star Simulation, but when I try to ping the PLC, I can't find it, much less talk to it via VisualStudio . How can I connect this PLC that is being simulated in GX Works3 in an external program?
  5. serial input string

    Hi  I'm quite new to plc but very new to mitsubishi.   I have an input string eg G+002.7 which represents a weight. I wish to take in the input string then move/convert to int omitting first char,   On other plc's i have been able to use a modifier like d200[2] then the no of chars. How do i achieve this in gx works3   Any feedback gratefully recieved   Paul  
  6. Alarms Acknowledge

    Hello experts, I have a problem with Mitsubishi, specifically about alarms and their acknowledge. Basically I would like to follow Siemens logic, i.e. when I have an alarm, I acquire it and only after this step can I reset it, so every time I have an alarm and want to reset it I have to acquire it first, but this means that every time I reset it and for some reason the alarm comes back to me, its acknowoledge has to come back working.  I hope I have made myself clear.  Does anyone know if I need to set something on GT Designer3 or do I have to adapt to Mitsubishi logic and do some programming on GX Works3? Thank you very much
  7. GOT 1000 ADMIN PASSWORD RESET

    hi good day, i have problem to reset my admin password in melsec GOT1000. it's because i didn't remember my old password. please help me to solve this problem
  8. Motion Control

    Hi Everyone.   I have been tasked with changing out an older Flex Drive servo drive to a more modern Micro Flex drive in a machine that has an Omron CQM1H-CPU51 PLC.  I'm having a few issues but hope that i can gain some clarity around at least one of the hurdles Im facing from here. Biggest issue for me at this moment is My work hasn't yet purchased a programming lead for this PLC (or even the bits required to make one myself) but i have a feeling the control for the Servo is done via motion control in the PLC.  Question here is, if changing from one servo drive to another type, will the motion control code need to be updated to work with the new servo drive?  I have very limited experience with motion control itself at this stage so I'm a bit lost when it comes to these sort of details. Regards Kiwi_man82
  9. GX Works3 Projectlib Locked

    Hello, I have a problem that I need to solve in a PLC program has it's projectlib locked.  I work for a company that contracted a PLC programmer before my time to program their new version of their control cabinets. The company did not write any specific contract with the contractor and just relied on his work. The guy later delevered a buggy software that is kind of functional (the bugs came up at the commissioning after the guy was paid and now he refuses to help or to provide more consultations). I have as a task to freshen this up and make it work without bugs, the problem is that the Projectlib is locked and I cannot access the source code.  The only thing that I can changes that I can make to the code is to put some logical circuits between the I/O of the already existing function blocks, which solved some problems, but not all and it keeps one of the most important ones as well. Anyways, that's my story, so now my question is, is there and possible way of unlocking the projectlib? Any feedback would be highly appreciated. Thanks in advace!
  10. Hello everyone I need help to Convert FX 5U program to FX 3U Plc. Is there any way to do so??? 
  11. Printinting from Mitsubishi HMI

    Hello everyone I have Mitsubishi HMI GS2110 WTBD- N. It is connected with FX5U with Ethernet protocol. I want to run a printer directly from HMI with RS 232 without using RS232 adapter card. Can someone please help me what to do and how to do. Regards
  12. is there is a function built in to convert chars like "XYZ.." to hex and vice versa ?? I am new to the iQ-R series and trying to figure it out, the GX-Works version that I am using is 1.038Q any help would be appreciated
  13. fx3uc-64mt/d

    Dear All , i Have FX3uc-64mt/d    plc. i am getting confused about its wiring . In manual it is mentioned that plc can be run on both sink and source while when i connect only OV to any pin it indicates the input high. although no signal is given to common terminal . can anybody explain me this phenomenon.  thanks in advance. 
  14. QD77GF Error D304

    Hi. I am using PLC Q06UDV wit QD77GF to operate 11 servos, it is my first time using QD77GF and CC-Link IE Field. I've done the parameter setting. but the qd77gf error lamp started to blinking. i try to check it in cc link ie field diagnostic and didn't find anything except the error lamp blinking in monitor view. then i checked system diagnostic , no error showing up but, only historical error when i started the power of plc. it show D304 error.  in manual book the solution are lengthen the operation cycle qd77gf, check the cable, and shorten plc scan time. where can i find this setting sir?  
  15. weight batching system

    Hello everyone, i am making a weight batching system , my system consists of 9 tanks each tank have a specific raw material , the user should be able to add a formula through scada system so he will be able to specify each weight of each ingredient to add to the formula. i have managed a connection between my weight indicator (pt650d) and my plc (fx3g) through fx3g232bd module (RS232 communication) , the weight indicator send data in ASCII to plc that we can show on the scada system .  so how can i change the ASCII numbers that come from the weight indicator to Decimal number without changing the value so i can control a barrel that will add raw material from the tank to the scale untill it reaches what the user specify in the scada ??   
  16. SLMP Failures

    Hello all,  I am new to using Mitsubishi and I am having issues communicating with my Cognex Camera. I have the camera configured in Datamn Setup Tool. I have the Ethernet card configured and validated. I am able to ping both devices and get a response on the network. However, I received an SLMP failure in Dataman and there's no communication between my camera and the controller.  Please see the attached photos to view how I have the camera and PLC configured.
  17. mitsubishi Register accessing

    Dear All i want to access a register of plc FX2N-16mr through modbus card FX2N-485-bd .   can any body help me out. i dont know any idea. any help will be a life savior. 
  18. Hello all,    I have 3 kinetix 5500 drives connected in series but some how the 3rd drive lost power. all the fuses in the cabinet look good. nothing else is tripped either.    any advice is appreciated.  thank you   
  19. PLC Reset?

    Hi guys, I always wondering, what is reset when reset button is click? Does the setting from address D from HMI will be lost? Does internal memory of PLC is reset? Anything thats not reset? Or just reset sequence? Thanks.
  20. Hi, I'm currently working as an intern, and my job is to transfer the program from a schneider twido twdlmda20rt to a mitsubishi fx5u-32mr/es. The thing is, i've been in trouble trying to understand and "translate" from one plc language to another certain things, like the %MW, %SW and blocks, so if any of You could give me some advisory I'd bee fully thankful (I can't upload all the pics, so theres's the link to the folder) https://inacapmailcl-my.sharepoint.com/personal/nicolas_gonzalez206_inacapmail_cl/_layouts/15/onedrive.aspx?id=%2Fpersonal%2Fnicolas%5Fgonzalez206%5Finacapmail%5Fcl%2FDocuments%2Fscript
  21. Hi everyone,  I am new to Mitsubishi PLC. I am trying to see from where Run or speed commands goes to Servo. I have MELSEC FX2M-32MT with FX2N-1PG cards for the Servo and I am using GX Developer 8.91v  Also, I would like to mention that initially I found out that BATT V light was lit so here what I didi. >I replaced the battery within 20 second while powered ON. Before changing the battery I took upload of the program successfully.  >I have cleared PLC memory and re downloaded the program.  > Checked Memory addresses M8005 8006 both are Low.  Now, when I am trying to run  my machine it is not giving output to two Servos while a conveyor operates when started from the HMI so it means program is inside PLC, right ? Program is attached if someone wants to have a look.  labeling mc 300322.rar
  22. Omron 1S Servo

    Hello:           Does anyone know the details explanation of the Homing Settings for the Axis? Set the homing operation. 0: Proximity reverse turn/home proximity input OFF 1: Proximity reverse turn/home proximity input ON 4: Home proximity input OFF 5: Home proximity input ON 8: Limit input OFF 9: Proximity reverse turn/home input mask distance 11: Limit inputs only 12: Proximity reverse turn/holding time 13: No home proximity input/holding home input   Limit Input referring to Input (I/O) ? How about Proximity Input ? It is confusing with the terms. The manual has no explanation for each of the above selection.   Any one?   Simon
  23. I would like to send ascii data  to other devices using RS232 interface. and the example format is "0009" (it is product counter machine marking). how can I do this? I am using q03ude, I usually convert 1001 to ascii using BINDA and use the last data (01). but, when it double word data e.g. : 100009 the last data is 9 and null, not 09 
  24. OT: Mitsu web redesigned

    Hello, since they redesigned the mitsubishi FA website I am unable to find software updates. Is it my fault or did they forget to put them in?   Thanks
  25. GOT2000 as MODBUS TCP slave

    I have this setup: FX3G CPU connected to GT2103 through RS422 (CH1). GT2103's ethernet port connected to LAN and set up as modbus TCP slave (CH2). I want to read/write PLC word devices using a modbus TCP client, from a PC. The HMI is acting as a gateway between PLC and PC. I used the Device Data Transfer function to send PLC's D register values to GT's internal GD registers. D0....D9 ==>  GD0....GD9 After some tries, I get valid response from the modbus slave. Reading the holding registers 0....9 (40001....40009), I get only zero values. Those registers can be written back with different values, correctly. I'm sure I didn't understand correctly the modbus address mapping to GT's internal memory. Can anybody help me? Thank you.