ALMIGHTY79

MrPLC Member
 View profile  See their activity

  • Content count

    36

  • Joined

  • Last visited

Posts posted by ALMIGHTY79

  1. Posted

    DL EP1 use TCP IP  but FX5U Only ethernet tcp,,You can use DL-EN1 or add module ethernet ip on plc

    and You can use dedicate program on plc fx5u with SOCKET communication,and You must set up on parameter ethernet port-->basic setting --> external device configuration ,and you just setting active communication module ( ip address and port number device and plc )

    you make program on plc  use function socket communication,

    SP.SOCOPEN, SP.SOCSND,SP.SOCRCV, and SP.SOCCLOSE 

    SORRY I WAS TOO LONG TO ANSWER,,2023
    
 

  3. Posted · Edited by ALMIGHTY79

    Dear sir.

    Hello Anyone
    I have Stepper motor with control  AZD KD and BLVD20KM ORIENTAL.I Want to communication with QJ71C24N Modbus rtu Mitsubishi ,How to make program and Drive motor to multi position and speed and to get moving home position.
    Please guide and show How to Communicate it,
    Thank you very much for your support.
    Best Regards

  7. Posted

    Thanks you for your reply,,Can you make me sample program ,dedicated instruction ZNWR and ZNRD.

    CPU 1.QO1CPU .

    SLOT 0 .QJ71E71-100.

    CPU 2.Q03UDE.

    SLOT 0.QJ71E71-100

     

    Thank you For your attention and support.

  8. Posted

    Dear Anyone.

    Anyone can help me.

    How to communication two plc Q SERIES MITSUBISHI.With QJ71E71 100.It Can Read/write .Can Show me. example instruction command ladder.or parameter

    CPU 1.D0 to d300.

    CPU 2 D400 to D700.

    Two Plc can Communication  read / write data register.

    Thanks you for your attention.20210525_103753.thumb.jpg.fb0e71e92982fe

  9. Posted

    On 13/04/2017 at 0:33 PM, Dhillis V C said:

    Hi,

    Thanks for the reply. I have used ZP.BUFSND & ZP.BUFRCV instructions for data sending and receiving. Also ZP.OPEN & ZP.CLOSE for port open and close. But port opening completion bit was not getting 

    Dear Sir.

    Can you show me .dedicated instruction with ZP.BUFSND AND ZP.BUFRCV.Thanks

  10. Posted

    Dear Sir.

    Can Anyone Help me,How To read  Holding Register QM30VT2 BANNER With QJ71C24N Mitsubishi ,With Rs 485 Communication.I Want To read Holding Register it,More than 2500 Register.

    Thank you for attention.

    Best Regards.

  11. Posted

    On 03/03/2020 at 8:34 PM, Djoko said:

    Master .

    Cpu  IP = 192.168.3.30.

    QJ71MT91  IP = 192.168.3.40

    SLAVE 1.

    CPU IP = 192.168.3.50.

    QJ71MT91 IP = 192.168.3.60.

    SLAVE 2.

    CPU ( Q02 H CPU ).

    QJ71 MT91 = 192.168.3 70

    I've tried it, without a CPU connection to Ethernet,But still 

    Until now my problem about Qj71mt91 has not been resolved and I have contacted a technician from the Mitsubishi agent but it has not been resolved either 😑😑😑

  12. Posted

    4 hours ago, Gambit said:

    What are the IP adressen of the CPU's.

    Have you tried removing the CPU from the network. 

    Master .

    Cpu  IP = 192.168.3.30.

    QJ71MT91  IP = 192.168.3.40

    SLAVE 1.

    CPU IP = 192.168.3.50.

    QJ71MT91 IP = 192.168.3.60.

    SLAVE 2.

    CPU ( Q02 H CPU ).

    QJ71 MT91 = 192.168.3 70

    I've tried it, without a CPU connection to Ethernet,But still problem

  15. Posted

    22 hours ago, Gambit said:

    But it does ping if the master is not comm with slave 1?
     

    22 hours ago, Gambit said:

    But it does ping if the master is not comm with slave 1?
     

    if the master and slave 1are stopped, Slave 2 can be ping and success

     

    On 25/02/2020 at 7:14 PM, Gambit said:

     

     

    On 28/02/2020 at 7:18 PM, Gambit said:

     

     

    there are no other devices connected to , only a notebook and 3 modbus installed 

  17. Posted

    On 28/02/2020 at 7:18 PM, Gambit said:

    looks ok is there any other equipment on the network ?

     

    On 25/02/2020 at 7:14 PM, Gambit said:

    Why don't you screencapture your settings so we can check it.

     

     

    On 28/02/2020 at 7:18 PM, Gambit said:

    looks ok is there any other equipment on the network ?

     

    there are no other devices connected to the switch, only the laptop and 3 modbus are installed, but when the master and the first slave are working, the second slave cannot  pinging , after being removed from the switch and  installed directly into QJ71 without the hub being connected

  21. Posted

    15 hours ago, Gambit said:

    Did you try another port on the switch ?
    Maybe the cable between de slave and the switch isn't a straight cable.
    Try the cable which worked on slave 

    Thank you sir.

    I have move cable slave 1st and slave 2nd, it's Working and success.but still problem when connect to second slave.there may be an automatic communication parameter error between master and slave, and I haven't found a way to set it