ALMIGHTY79

MrPLC Member
  • Content count

    36
  • Joined

  • Last visited

Everything posted by ALMIGHTY79

  1. DL EP1 use TCP IP  but FX5U Only ethernet tcp,,You can use DL-EN1 or add module ethernet ip on plc and You can use dedicate program on plc fx5u with SOCKET communication,and You must set up on parameter ethernet port-->basic setting --> external device configuration ,and you just setting active communication module ( ip address and port number device and plc ) you make program on plc  use function socket communication, SP.SOCOPEN, SP.SOCSND,SP.SOCRCV, and SP.SOCCLOSE SORRY I WAS TOO LONG TO ANSWER,,2023  
  2. QJ71E71-100 CONFIGURE OPC SERVER TAKEBISHI

    I have getted how to setting qj71e71 communication with opc server takebishi and it's running well, it's very simple setting, data from plc can be sent to database pc.  
  3. Dear all member forum plc , Hello anyone can suggest me,how to communicate QJ71E71-100 WITH OPC Takebishi,How to to configure parameter on QJ71E71 -100 and OPC server Takebishi,I Want to aqcuisition data machine to database,
  4. Dear sir. Hello Anyone I have Stepper motor with control  AZD KD and BLVD20KM ORIENTAL.I Want to communication with QJ71C24N Modbus rtu Mitsubishi ,How to make program and Drive motor to multi position and speed and to get moving home position. Please guide and show How to Communicate it, Thank you very much for your support. Best Regards
  5. QJ71E71 100

    Dear Anyone. Anyone can help me. How to communication two plc Q SERIES MITSUBISHI.With QJ71E71 100.It Can Read/write .Can Show me. example instruction command ladder.or parameter CPU 1.D0 to d300. CPU 2 D400 to D700. Two Plc can Communication  read / write data register. Thanks you for your attention.
  6. QJ71E71 100

    I have trial it.With dedicated instruction ZP.BUFRCV AND ZP.BUFSND.. CPU 1 Send D2300 ..CPU 2 RECEIVE D60. CPU 2 SEND D60...CPU 2..RECEIVE D2300. Succes communication with two plc.         PLC 1 (QJ71E71-100) OKE.gxw PLC 2 (QJ71E71-100) OKE.gxw
  7. QJ71E71 100

    Thanks you very much for your response.I will try it.
  8. QJ71E71 100

    Thanks you for your reply,,Can you make me sample program ,dedicated instruction ZNWR and ZNRD. CPU 1.QO1CPU . SLOT 0 .QJ71E71-100. CPU 2.Q03UDE. SLOT 0.QJ71E71-100   Thank you For your attention and support.
  9. QJ71E71-100 to QJ71E71-100 Data Transfer

    Dear Sir. Can you show me .dedicated instruction with ZP.BUFSND AND ZP.BUFRCV.Thanks
  10. QM30VT2 BANNER WITH QJ71C24N

    Dear Sir. Can Anyone Help me,How To read  Holding Register QM30VT2 BANNER With QJ71C24N Mitsubishi ,With Rs 485 Communication.I Want To read Holding Register it,More than 2500 Register. Thank you for attention. Best Regards.
  11. Dear sir,  all the master plc in the world. I'am newbie about modbus TCP/IP qj71mt91 modul mitsubishi. I have problem to configure   qj71mt91 with master and slave .I have 3 qj71mt91 and one of them  for master slave. I connect with switch ( hub) Please suggest me how to set up or configure parameter for master and 2 slave  Slave first = d0 to  d300.( Read by master)                    = m100 to m300 ( write from master ) Slave 2nd = D500 to D1000 ( read by master )                   =  M400 to m500 ( write from master) Master Ip addres.192.168.3.45.( CPU )                                 192.168.3.50.( QJ71MT91) Slave 1st = 192.168.3.39( CPU )                  = 192.168.3.40 (QJ71MT91) Slave 2nd = 192.168.3.60 ( Qj71mt91) Thanks for your attention and support. Best regards . Udjojojo
  12. Until now my problem about Qj71mt91 has not been resolved and I have contacted a technician from the Mitsubishi agent but it has not been resolved either 😑😑😑
  13. Master . Cpu  IP = 192.168.3.30. QJ71MT91  IP = 192.168.3.40 SLAVE 1. CPU IP = 192.168.3.50. QJ71MT91 IP = 192.168.3.60. SLAVE 2. CPU ( Q02 H CPU ). QJ71 MT91 = 192.168.3 70 I've tried it, without a CPU connection to Ethernet,But still problem
  14. there are no other devices connected to , only a notebook and 3 modbus installed 
  15. If Master and slave 1 are connected  ,slave 2 cannot pinging,sometimes it can be connected, after 12 times time out
  16. there are no other devices connected to , only a notebook and 3 modbus installed 
  17. there are no other devices connected to the switch, only a notebook and 3 modbus installed 
  18. there are no other devices connected to the switch, only the laptop and 3 modbus are installed, but when the master and the first slave are working, the second slave cannot  pinging , after being removed from the switch and  installed directly into QJ71 without the hub being connected
  19. only slave 1 and slave 2 are configured by distinguishing the ip address.Other parameter not set
  20. Hello mr.@NevergoldMel. Can you show me example? How to configuration master and 2 slave Qj71mt91 ? 🙏🙏🙏
  21. Thank you sir. I have move cable slave 1st and slave 2nd, it's Working and success.but still problem when connect to second slave.there may be an automatic communication parameter error between master and slave, and I haven't found a way to set it
  22. Slave 1st .192.168.3.60.       Slave 2nd.192 .168.3.50. If slave 2nd ( qj71mt91) test ping direct with straight cable to PC has success,but if through switch cannot responding. Whats wrong ?
  23. I have make automatic communication parameter 2 with different IP and BFM,But  Still problem ,Cannot communication with second slave ,Alarm appears on diagnosis system monitor
  24. 😇😇😇🤕🤕...