-
Content count
10 -
Joined
-
Last visited
Community Reputation
0 NeutralAbout MrJustinPLC
-
Rank
Sparky
- Birthday 05/03/94
Profile Information
- Gender Male
- Location Ohio
- Country United States
Recent Profile Visitors
-
Learning about MicroLogix 1500
MrJustinPLC replied to Triplett's topic in Allen Bradley / Rockwell Automation
it took me a little to get used to it, I like CCW now, and its not just for controllers. setting/backing up drives is a breeze compared to executive. -
Learning about MicroLogix 1500
MrJustinPLC replied to Triplett's topic in Allen Bradley / Rockwell Automation
Whats wrong with the 850s!? I like them -
MrJustinPLC liked a post in a topic: Learning about MicroLogix 1500
-
MrJustinPLC liked a post in a topic: Communicating between plc's with different IP's
-
ASI System Faults SLC05/03
MrJustinPLC replied to MikeRush's topic in Allen Bradley / Rockwell Automation
ASiMon? -
232 DH+ Pass through 5/04 PB32
MrJustinPLC replied to MrJustinPLC's topic in Allen Bradley / Rockwell Automation
I'm pretty sure PanelBuilder is older than me -
MrJustinPLC liked a post in a topic: Change P in running PID
-
232 DH+ Pass through 5/04 PB32
MrJustinPLC replied to MrJustinPLC's topic in Allen Bradley / Rockwell Automation
So I tried that a few times and i even tried downloading with my program and it never showed. A few articles online say that PB32 will not work with windows 10. I decided to try the memory card again. It had failed 3 times before it actually loaded into the program but it worked. Some sites suggested using VM and installing windows XP but I wasn't desperate enough to do that. I am going to update this system shortly to 5000 and put it on our network, this is the only system in our plant still using DH+. Thank you, I appreciate your help! -
MrJustinPLC started following Mickey
-
232 DH+ Pass through 5/04 PB32
MrJustinPLC replied to MrJustinPLC's topic in Allen Bradley / Rockwell Automation
-
232 DH+ Pass through 5/04 PB32
MrJustinPLC replied to MrJustinPLC's topic in Allen Bradley / Rockwell Automation
You were correct the cable was wrong, lesson learned. I can now see the HMI in Linx but it shows no drivers available in Panelbuilder. -
232 DH+ Pass through 5/04 PB32
MrJustinPLC replied to MrJustinPLC's topic in Allen Bradley / Rockwell Automation
I see. I am using a sealink usb serial adapter. I also have 1747 UIC I could try. I also tried the memory card at fat 16. The command line i use is "copy %s F:" seems like it copies, but t doesnt make it over. -
MrJustinPLC liked a post in a topic: 232 DH+ Pass through 5/04 PB32
-
232 DH+ Pass through 5/04 PB32
MrJustinPLC replied to MrJustinPLC's topic in Allen Bradley / Rockwell Automation
Im not sure if the port is damaged, but I have tried multiple times to communicate via 232 and it will not. I just tried again with no luck, I can communicate with the SLC no problem. The catalog number is 2711-T6C8L1 -
MrJustinPLC changed their profile photo
-
I have an old system that needed some HMI modifications, it comminucates with DH+. The 232 port on the HMI does not work even if I disable the printer. I have tried to create a memory card with a linear flash but the HMI says it is not formatted correctly. I was able to get the DH+ pass through on the processor to show the Panelview on RsLinx however PanelBuilder32 can not communicate with it. Perhaps I am making the memory card wrong? Windows 10 with latest version of AB software. I am not too familiar with Panelview or DH+, so anything helps. Any help would be greatly appreciated. Thanks, Justin
- 13 replies
-
- panelbuilder32
- 5/04
-
(and 2 more)
Tagged with: