Yotis

MrPLC Member
  • Content count

    4
  • Joined

  • Last visited

Community Reputation

0 Neutral

About Yotis

  • Rank
    Hi, I am New!

Profile Information

  • Country United Kingdom
  1. Negative RLO bit

    Hello, thank you so much for your reply. I appreciate it.  I was trying to use that diff down earlier but it didn't seem to be functioning how I wanted it to. I have since managed to figure it out. Happy days!   RLO = Result of logic operation
  2. Negative RLO bit

    Hello, Is there something similar in CX-Programmer to the (N) bit in Siemens programming software? If so, what is it called please?
  3. Hello Jay,

    I could see you're an Omron Expert and I am in quite a pressing situation. I though I might be better commenting on here.

    Im quite new to working with Omron. I am struggling very much to get online with an Omron CPM2C-S110C. It has a CIF01 card also. I hear this PLC is quite an old one.

    I have referenced the manual on 'connecting a computer running support software' and double checked I have the correct cables.

    The ones I am using and the way I am connecting is:-   

    PLC Peripheral port >> CS1W-CN118 >> XW2Z-200S-CV >> serial to USB >> Laptop

    Also

    CIF01 Peripheral port >> CS1W-CN118 >> XW2Z-200S-CV >> serial to USB >> Laptop

    I have also tried RS232 to UBS in replacement for the Serial to USB.

    Checking on Device Manager, I have all the drivers installed, the comms ports are correctly numbered yet I still cannot connect. There are 4 dip switches on the top right hand side of the CPU and all are swiched off. I have called Omron Tech Support and they said to ignore them in this instance.

    The RS232C port on the CIF01 is used by a barcode scanner so there is no means to connect through that (I have been told)

    I feel that I have been through setting and checked in CX-Programmer and nothing looks obscure.

    Please offer me any ideas you may have. I would greatly appreciate it.

    Thank you

  4. Cannot get Online - CPM2C

    Hello Ladies and Gents, Im quite new to working with Omron. I am struggling very much to get online with an Omron CPM2C-S110C. It has a CIF01 card also. I hear this PLC is quite an old one. I have referenced the manual on 'connecting a computer running support software' and double checked I have the correct cables. The ones I am using and the way I am connecting is:-   PLC Peripheral slot >> CS1W-CN118 >> XW2Z-200S-CV >> serial to USB >> Laptop Checking on Device Manager, I have all the drivers installed, the comms ports are correctly numbered yet I still cannot connect. There are 4 dip switches on the top right hand side of the CPU and all are swiched off. I have called Omron Tech Support and they said to ignore them in this instance. The RS232C port on the CIF01 is used by a barcode scanner so there is no means to connect through that (I have been told) I feel that I have been through setting and checked in CX-Programmer and nothing looks obscure. Please offer me any ideas you may have. I would greatly appreciate it. Thank you.
  5. Can I download program to FX5U By SD card

    Hello, I have been sent a zipped file over email to unpack and put on an SD for tranferring to FX5U-32M PLC that currently has working code on. I unpacked the file and put it onto the SD card.  The procedure seems to be almost fool proof, however I am getting an error LED when I switch the PLC back on. I havent got the Mitsubishi software to hand and havent used this method before, am I missing something? I tired having the folder with the contents on the SD card and then just the contents not in a folder on the SD card to no avail. Both error. Could I have been sent a corrupt/incorrect file or do I need to wipe the PLC's current code before it'll look at the SD card for a program?  Does it have to be a specific spec SD card? Any advice would be nice, thank you! Yotis