zpassha

MrPLC Member
 View profile  See their activity

  • Content count

    21

  • Joined

  • Last visited

Community Reputation

0 Neutral

1 Follower

About zpassha

  • Rank
    Sparky

Profile Information

  • Country Czech Republic
  1. Raza khan started following zpassha

  2. Collision avoidance R04CPU R16RTCPU error

    zpassha replied to zpassha's topic in Mitsubishi

    Upload the program

  3. Collision avoidance R04CPU R16RTCPU error

    zpassha replied to zpassha's topic in Mitsubishi

    Yes only into R04CPU
  4. Good day I have a problem with collision avoidance, I get this error by upload a program to R04CPU error is ES:010a41d1? Can you help me?

  5. Keyence Vision System and Mitsubishi

    zpassha replied to Fleidimir Andrade's topic in Mitsubishi

    What CVX you have?

  6. Euromap

    zpassha posted a topic in Mitsubishi

    Good day people, how work euromap 67 on Mitsubishi PLC, the ENGEL need work with euromap between Robots  and ENGEL

  7. Mitshibisi to Fanuc Robot with cc link

    zpassha replied to Dirk van Zyl's topic in Mitsubishi

    Try this documentation https://www.mitsubishielectric.com/dl/fa/document/manual/plc/sh081270eng/sh081270enge.pdf Page is 73

  8. RJ71EIP91

    zpassha replied to chrisb4748's topic in Mitsubishi

    Problem solved you must turn on communication bit Y10 on CPU look here Element - Module - Module Label - RJ71EIP91 - Output Signal - bSetCommunicationStartupRequest or use FB GetInputData or SetOutputData. and the next problem was a bad EDS file. 

  9. RJ7EIP91 and R04CPU communication with EX600 by EIP

    zpassha replied to zpassha's topic in Mitsubishi

    Thanks all the problem is solved.  EDS file for SMC EX600-SEN3 have bad parameters after correct  unit run perfectly.

  10. RJ7EIP91 and R04CPU communication with EX600 by EIP

    zpassha replied to zpassha's topic in Mitsubishi

    Thx for reply, but configuration is ok, but i dont switch any bit or get status in plc, or send bit t9 switch any solenoid
  11. zpassha liked a post in a topic: RJ7EIP91 and R04CPU communication with EX600 by EIP
  12. Good day, how can I communicate with SMC EX600 by Ethernet/IP have you any exemple? I do a setup by EIP configuration tool and write into EIP module but I cant switch any bit into EX600. Thanks
  13. Good day, how can I send string data by buil-in ethernet. Maybe word 'TRIGGER,?

  14. FX5U and FX5-ENET/IP

    zpassha replied to Levent1970's topic in Mitsubishi

    Fx5-enet/ip on Mitsubishi pages, the first device send bits start u1/g60000 and get hits on u1/g12000
  15. Good day, I need help, how I read data from Balluff BVS001C Identification over ethernet? Thx a lot
  16. zpassha liked a post in a topic: FX5U ENET/IP communication with EX260-SEN1

  17. FX5U ENET/IP communication with EX260-SEN1

    zpassha replied to zpassha's topic in Mitsubishi

    Thank you for your reply, I read your topics before, and now when you say me about buffer variables I read a documentation  about fx5 enet/ip module and all is running perfectly. Tnx a lot
  18. Good day, I have Mitsubishi SN 18xxxxx with new firmware 1.111 and attached FX5-ENET/IP module to communicate with SMC EX260-SEN1, have you any example how send data into SMC over Ethernet/IP? Thanx for reply