future
MrPLC Member-
Content count
29 -
Joined
-
Last visited
Posts posted by future
-
-
Dear All
My system includes Module 1747-SDN which controls Micrologix via Module 1761-NET-DNI but Now Module 1761-NET-DNI is broken and I replace a new but the system issue error on both Module 1747-SDN and 1761 -NET-DNI.
I don't know what I have to do when I replace Module 1761-NET-DNI?Thank you very much
-
Thanks Gambit
I have installed the Gx Configurator DP latest version 7.14Q and It is Ok
Thanks for your strong support
-
Thanks for your help, waynes
I have installed Version 1.580E and a few other versions but it is not Ok
I don't know why? do I need to install more other software to read the project in Instruction List? do I need to pay attention when installing Gx Works 2 software ? do I need to change anything on the Gx Works 2 software? .....Thanks You
-
Thank Gambit
I send you the Project
I look forward to hearing from you
-
Hi Everyone
When I open a project with Gx Works 2 but it is not possible to open project and issue error "it is not possible to open projects with IL Pous with this version of gx works 2" although I installed some version of Gx works 2 : Version 1.501x, 1.513k, 1.560J, 1.596w..... but is not Ok
Now I don't know how to resolve this problem?
Thank you so much
-
Thanks Gambit
I think so
I will request the password from programmerThanks you so much
-
-
Thank Mr. Gambit
I also think that the program can be programmed with an older version
I will Download all Program to GOT later but I don't know if There is any problem when Download all programs with different Version? and I suppose it will take a lot of time when editing the program and Download to GOTThank you very much, Mr. Gambit
-
Thanks Mr Gambit
If I create a new project and Download it to GOT, I can select between ''Synchronize'' and '' Select '' to Download.
But when I Upload Program from GOT and then Download that Program to GOT or change in a Base Screen (for example: add a Switch ,Lamp...) and then Download to GOT => I cannot select '' Select '' Mode to DownloadThanks for your reply
-
Thank Mr Gambit
I have used the latest software (Ver 1.217B) but cannot select from '' Synchronize '' to '' Select '' mode.
Thanks for your help!
-
You have to select FXCPU not QCPU
-
-
Thanks you so much
I already opened the project after updating the latest Version Got 2000
Thanks for your help
-
Thanks Mr.Bryll
When I upload the program from HMI, it is reported that It can be saved but it cannot be opened as the image below
I am sure the project was written on Got 2000 (Model of the screen is: GS2110-WTBD) so it cannot be opened with Got 1000, even though I have visited Mitsubishi's website and updated to the highest version (Got 2000 Ver 1.217B)
Thanks so much
-
Thanks Mr.Theo V
I have visited Mitsubishi's website and have updated Version Got 2000 but I still can not open the project even though my Version is higher than the Version of the project
Thanks for reply
-
-
Hi everybody
My system has 5 servo motors controlled by CPU Q170MSCPU and Q170MSCPU is controlled by Encoder with number of pulses is 3600P/R but the problem is that this Encoder is broken and I don't have this type of Encoder to replace but I only have Encoder type with number pulse of 600P/R.
So I don't know which parameter I have to change in the MT Developer 2 program so that the system will work well with the Encoder with pulse number of 600P / R
We wish the help of everyone
Thank you advance -
Great, I connected 1747-UIC to the computer
Thank you so much
-
Hi everyone
I have a 1747-UIC cable but there is no driver of the cable, I have searched it on the internet but I do not see anything, So you can give me the driver?
Thanks so much
-
Thanks for your reply, Now I understand how to connect between them
Thanks you so much
-
-
-
Thanks Kaare_t
If I use the software Gx works 2 and Read from Plc and Verify will match with plc but in this case unfortunately all FB in the program is lost completely.
If I use original program and modify to That program Match with Plc so I have to spend a lot of time
so do you know how to use the original program and upload override the original program and the program is uploaded have FB and fully Match with plc
Thanks for your help
-
Hi Everyone
I modify the program on gx works 2 (in the program somewhere was programmed by FB) then downloaded some program to Plc (Q06UDEH) but then I accidentally deleted that program on my PC and I took the program that was not modified before( original program ) and upload from PLC when uploading finished I made Verify but the program was uploaded Mismatch with PLC as picture below. Now I do not know how to get my original program (have FB and comment) and upload the program from Plc and Verify to match with Plc? please help me!
Thanks
Error On 1761-NET-DNI and 1747-SDN
in Allen Bradley / Rockwell Automation
Posted
Thank you very much, BobLfoot
My broken module 1761-NET-DNI has address 29 and when I replace a new I know that Module 1747-SDN does not recognize this new module because of the wrong address
so what should I do to make 1747-SDN recognize 1761-NET-DNI with the address 29, I have read the 1761-NET-DNI documentation but I don't know how to do it? can you give me some suggestions?
Thank you so much