Dariusch

I not big fan of the Invert (ctrl+alt+F10) in the ladder. I would rather use the not equal  "<>" instead of  "=" and remove the invert. But ok, yes it will Work for you.

Do you use structured project? Then you can put in a "ST" in the ladder. That is pretty cool.

Hi Andrei, You want to detect the change of value for ZR1200? Maybe this can help? /Dariusch

Yes probably. I always test functions and new FB's on a PLC. But a Q50UDEH is not cheap have extra on the desk      

ok, you are running a simulator and not on PLC? I have not tried the simulator, but I think it could be a explanation. /Dariusch

1) You have checked that it is not used any other Places? 2) Try make a new timer just 1 NW after and run it with a 100ms puls (SM410) LD SM410  OUT T151 K100 /Dariusch

You use a lowspeed timer. Can you please try change ZR1204 with a constant ie. K100  

Hi Andrei, Do you use the instructions OUT and OUTH? Maybe send a screendump of the NW

Hei Andrei, Please have a look at the manual in the download section "QnUCPU - User's Manual, Function Explanation, Program fundamentals" Chapter 9.2.10 Timer (T) page 382. Setting up low and highspeed timers se attached "Timer_setup1". You could also use as IEC timers. se attached "Timer". Hope this get you started, else get back. /Dariusch  

View File QnUCPU - User's Manual, Function Explanation, Program fundamentals QnUCPU - User's Manual, Function Explanation, Program fundamentals Basic, good to know. Submitter Dariusch Submitted 02/22/17 Category Manuals, Tutorials

Hi Letranlong, Can you plase tell us the Error-code you get? Maybe some screendumps.   /Dariusch

Hi there, I have made some FB's in IEC/GXW2 that I have importet in the GXW3 Lib. Some of the FB's include functions with the EN/ENO where in IEC/GXW2 was possible to disable the "Hold output" when not executed. Please see attached. I have spoken with Mitsubishi and they say it is not a functionality in the GXW3. Any one here with experience of how to workaround this? Or do I have to rewrite my code? Best regards Dariusch  

Hi aakash, I have not quite understood what exactly you have trouble with. But I maybe think you are missing some settings for the remote I/O-stations. I seems at default settings.   /Dariusch  

Aha... If you have enabled the "IP Packet transfere setting" you get the error. You have to check if your application can run without this setting. /Dariusch

Hi, Strange. Works fine here.   /Dariusch

Hi Andrei, What PLC and HMI are you using? It is possible to export both PLC- and HMI-program to a USB and download through a Beijer IX-panel to a FX-PLC.   /Dariusch    

Please DO NOT delete the OEE from POU-pool!! The Taskmanager control the execution of the programs in the POU. You still have to make a compile, so it all has to be Black and not red as in your screen. /Dariusch

Hi Gambit, Thank you. That just did it...    

Hi, Anybody have used the FX5U with a E1000 panel? I try to connect to a E1071 using the MC-Protocol driver in the E-Designer. Usually in the GXW2 or IEC for the Ethernet I can setup the "Destination IP Address" to "255.255.255.255" (Broadcast Together), Choose port for both ends and voilà thanks in advance Best regards Dariusch

I usually use the fileregister [R] or entended fileregister [ZR] when I have to make som sort og recipehandling, datalogging, datatraceing or need of lots of registers for calculating. Also in my opinion a good way of storing data for example program/machine setup. The [R] registers can be created at the expense of the standard RAM of your CPU (build-in memory) or by using a SRAM-Card for creating up to 1mill. [ZR] extended registers. Also the registers are latched by default. Best regards. Dariusch

The function would still be there in your version. Please Try type in "DEMOV" or "DEADD" NOT "EMOV" or "EADD" Dariusch!

With GX-DEV. Version 8.78G

Hi Dave, It is in the manual. Please look at the pics. Also tjek for the version of the CPU. It should be version 2.20 or later.

It is not that easy to conver from IEC.... Will see if have time next week to find a solution /Dariusch