Face Book

Hi Sir, Iam confuse about the procedures for Connecting remotely into simatic cpu through teamviewer VPN in a certain document in internet " JesperMP "  describes to enable IP routing in remote PC . In other document describes to enable IP routing  in office PC. In other document,enable IP routing in both PC. I do not know what is the correct. Can you explain this point? Thank you in advance. How to setup Teamviewer VPN.pdf

Hello, Please explain How to set TeamViewer  VPN for programming remotely with Bckhoff PLC and Beckhoff HMI/IPC? The engineering tools installed only on the local PC and the Remote is a Gateway to the PLC. I installed the following software on the local PC:TwinCAT V2.1 and TeamViewer V11 On the remote PC:TeamViewer V11 installed and this PC  connected to Beckhoff PLC and HMI/IPC We want to use the local PC to access the remote PC through internet and diagnose the problem of Beckhoff PLC or HMI/IPC What are the possible ways to perform this action?   Best regards....

 Hi, The designer not gave us this information. Do any member have this manual? https://www.classicautomation.com/Part/cp7702-1420-0040 Thank you in advance.

Hi, In our  filling machine:  the designer installed Beckhoff CP7702-1422-0040 This CP contains a digital  I/O modules  inside it at the back side . Do any member have any docunent or manual that explains how to program the Buttons and the lamps in the front side? Waiting your replies. Thank you in advance.  

Hi Sir, Thanks for your reply. I saw and read it but did not find the input signal for each button when press it  and the output signal for each button lamp to energizer it. Please help me because Beckhoff support not helped.  

Thank you for your help

Hi Can you explain how to integrate B&R modules into Simatic Manager program and what is the difference between these modules as in the attached photo?

Hi Please Check the addresses in the attached photo. Am I right?

Hi If we have  X67DM1321.L08   I/O as in attached photo in HW Configuration: I  Address:86.......91 Q Address:86....89 What are the addresses for these channels in this case?

  I need to know how to address I/O for these modules in general?   "these modules contain large byte of I/O addresses"

Hi  What are the physical I/O addresses that used in these modules? "these modules contain large byte of I/O addresses"

Can you draw a  diagram explain the connection between the modules?

Yes But Iam not understand the connection between them Can you draw a  diagram explain the connection between the modules?

Hi 1-How the modules connected in the table in the attached photo? 2-What is the difference between them? 3-What is the relation between  X67BC6321.L08 and the modules in the table?

NO ----- I don't find  all of these I/O address in the PLC modules ------ What is the relation between  X67BC6321.L08 and the modules in the table? ------ Module: X67DM1321.L08 and reserve 10 byte for digital 16 I/O Module How?    

Hi X67BC6321.L08 X67DM1321.L08 And other modules I don't find  all of these I/O in the PLC modules

HI The program is already run without any problem as the designer do. I need to know the concept of this.

Hi Can any member draw  the ladder diagram for this application: 1-O/P pulse high from the photocell sensor to enable rejection system 2-Bottle passes in front of another photocell and after certain time O/P is high"rejection arm"for a certain time. 3-If O/P pulse low from the photocell sensor: nothing to do Thank you

Hi Iam newbie in TwidoSuite software. My question: What are the procedures to download or upload a program from or to PC using TwidoSuite V2 software?   Thank you

Thank you very much for your support

Hi Thank you very much for your support. 1-Sorry,Iam not understood all the ladder diagram. Can you explain it? 2-Where are the signals of sensor tracking position and rejection sensor  in the ladder diagram? 3-What do you mean by conveyor indexed signal?

Hi 1-I will install the rejection sensor and rejection arm followed to detection sensor to simplify the application. 2-rejection arm will be active for certain time after  the bottle detected by rejection sensor after certain time. Can you draw  the ladder diagram for this application? 

yes Can you help me?

Thank you very much for your support.

Hello, Thank you very much for your support.  1- Can you explain  only the last step you did  for remote access to Beckhoff PLC/HMI as attached file with photos?   2-Iam not understand this point: " in TwinCAT System Manager when you go to "Add Route Dialog" you have to enter IP address of the PLC in the "Enter Host Name / IP:" field and click on the button (not "Broadcast Search" as if you are searching for the PLCs in the LAN). And yeah, I didn't have 2 network adapters on the remote PC as it is stated in the PDF, remote PC and PLC are both connected to an ordinary ethernet switch. " 3-Why do you not select:Broadcast Search ? 4-Explain this point: "  I didn't have 2 network adapters on the remote PC"  You intend :2 Adapters on Remote PC or on Local PC which contains the engineering software tools?   Thank you in advance.