KCRP
MrPLC Member-
Content count
22 -
Joined
-
Last visited
Community Reputation
0 NeutralAbout KCRP
-
Rank
Sparky
Profile Information
- Country India
-
See below Pic for the Communication in between the remote devices.
-
Initially i configured Refresh setting for CC LINK IE FIELD is X2000 & Y2000 also cannot get signal
-
Hi @Gambit ,Thanks for a reply. Actually my refresh settings is X2000 AND Y2000 and I tried with X2000 and Y2000 i never get a ON/OFF signal. Then i change to X200 and Tried also no signal.
-
KCRP started following "CC-LINK-IE-FIELD" Remote Device IO Communication
-
Hi, I am using IQ-R Series "R16ENCPU" With Inbuild CC-LINK IE FIELD "RJ71EN71" and attached CC-LINK "RJ61BT11". Problem is, Even though my remote IO cards are in Online connected with masters, I cannot able to On/OFF Remote Device station IOs in CC-Link IE FIELD network. But CC-Link Normal is working fine. Refresh settings and Network Config Settings are done, Below attached the pics for reference. I cannot able to find the problem, Can anyone help me in this.
-
KCRP started following USB DRIVER SOFTWARE DOWNLOAD
-
Hi, I want to download the USB Driver Software for the Mitsubishi FX3GE-40M PLC, Can anyone help me where to download this driver software.
-
Thanks for your reply @sparky, What are all the parameters must to change?
-
KCRP started following FR-F740P-15K
-
HAI Everyone, I have doubt regarding the selection of Inverter(VFD) for the Blower. Actually i bought 13kW 380V 50Hz blower along with Mitsubish Inverter FR-F740-15K.(15kW inverter). Now i changed to new Blower with low capacity of 5.5kW 380V 50Hz, but i never changed the Inverter to lower capacity. Now what is my doubt is whether i can use the same inverter or i need to change?
-
How to connect More than one Omron Cj2m Cpu Plc in a same network
KCRP replied to KCRP's topic in CX-Programmer
How to do with network configurator -
Hi i am new to Mitsubishi servo drives, i want to know how to Tune the Mitsubishi (MR-JE-A-200w) servo drive Can any one guide me please
-
How to connect More than one Omron Cj2m Cpu Plc in a same network
KCRP posted a topic in CX-Programmer
Hi, I am doing a project with three Omron Cj2m cpu. I dont know how to connect More than one Omron Cj2m Cpu Plc in a same network to communicate each other with a Internal Memory addresses. Can any one help me to understand? -
Thank you..so much sir for your valuable reply. This website is very useful. i like it. i am just a beginner for this PLC field please help me if i ask some questions.Thanks.
-
Thank you..so much for your reply. This website is very useful. i like it. i am just a beginner for this PLC field please help me if i ask some questions.Thanks.
-
Hai, I am doing program for Mitsubishi FX3U Series PLC i don't know some options in that can any one help me to sort out this. 1) I assigned the Address Y040 for one output, suppose during the machine running this output is in ON condition, if the plc power went Off and On again, the output should be in the same previous state. can we do this? How? 2) If i switch OFF the PLC power and Switch ON again i want to switch ON one Input Contact, only for the first time. What is that one scan ON input Address? Please reply fast if you know..
-
KCRP started following FX3U Series DOUBT
-
Hai, I am doing program for Mitsubishi FX3U Series PLC i don't know some options in that can any one help me to sort out this. 1) I assigned the Address Y040 for one output, suppose during the machine running this output is in ON condition, if the plc power went Off and On again, the output should be in the same previous state. can we do this? How? 2) If i switch OFF the PLC power and Switch ON again i want to switch ON one Input Contact, only for the first time. What is that one scan ON input Address? Please reply fast if you know..