[VFD ATV610 Parameters Commissioning]

You can use a browser or there is a software soMove, but for this you will need a special cable.

Banker

[OneShot CX-programmer]

Hi

Programming a CJ2M in ST is there a oneshot instruction and how to use a timer ? 

PS I now how to program a oneshot.

Banker 

[CPU load memory]

Use the cross ref. in CX-programmer

Banker

[Split long word for average function in function block]

Why not 64 bit real ?

[CXSupervisor, CJ2M performance issues.]

Ethernet has most better performance 

[Using a AD041 and DA041]

Hi 

You need to start the card 2020.0 , 1, 2, 3 one bit pr channel.

Sorry my mistake you have already started the card, but the address for writing is 2021 unit no.2 ch.1

Banker 

 

[CJ1W_AD081_V1 Fault after power reboot]

Hi 

Use the Cross-ref ( ALT -X ) and you can see that the program use D20XXX in the section Bally_Flow_AVG

You have a functionblock AVG300 with AT_D20000

 

 

Banker

[CX-Supervisor runtime startup question]

The PLC is in run mode. 

[2 CPU CJ2M on one PSU]

HI

Is it possible to have 2 CPU on the same PSU ?

Banker

PS. only using remote I/O

[Cx supervisor with cx designer and cx programmer]

Yes you can install cxs on the same PC as cxone. 

[PrintActivePages(FALSE) scales text and graphics differently]

Hi 

I got a beta ver 341(3) and I also have isue printing.

Banker

 

[CX-Supervisor 3.4.1]

Problem solved By Omron Denmark: Mark all point and press <Enter> Then Press <OK> 

[CX-Supervisor 3.4.1]

Hi

After updating CXS to ver. 3.4.1 I can't see point address I can see them when I editing but in the list form only the array len. is shown. When I enter a new point I can see the address.

Anybody now hove to solve that ?

Banker

[setting the Ip adress of Omron CJ2M PLC using browser.]

By default the address is 192.168.250.1 

Banker 

[CJ2M 33 Ethernet/IP problem]

Thanks for the suggestion, but I want to avoid a solution with an extra relay. I had this setup with Omron PLC but on profibus, no problem because the comms. stop when the PLC goes into stop.

Banker

[CJ2M 33 Ethernet/IP problem]

Hi

I have a problem. I have a PLC CJ2M with Ethernet/IP comms to some Danfoss drives FC280. I can start and stop the drives, control speed ect. BUT when/if my PLC goes into stop the drives continues. The drives have at controlword with a bit 10 Data valid bit ( most be On otherwise controlword will be ignordet ) When the PLC goes into Stop the Ethernet/IP continues to comm. so if i use DM memory for the comms it will not change. If i use CIO memory i all go 0 and the drive ignor the controlword. What to do. ???

Banker

 

[MAD 42]

Try i out in the simulater and if not make a convert from 16 binary to INT or use ther >S 

¨Banker

 

[Cx-programmer -Flowmeter]

Hi Kenra

What do not match ? the program is a totalizer I7.13 input oneshot. D3174+D3175 is the totalized value. 

Banker

[Remote NX IO via NXEIP202 card]

Hi

In france but maybe it can help.

https://www.youtube.com/watch?v=oP5RQ7BHx5M

[Remote NX IO via NXEIP202 card]

Hi

I think you need Netconfigurator in CXOne

 

[How to connect Cx designer to PC]

Hi 

In you can run your cxdesigner project in test mode on you PC at connect the project to a PLC.

Banker

 

[Analog Input to CP1E from MX2 Drive]

BobB it a function blok

[CJ2M-CPU33 bus unit]

You have already ethernet/IP in this CPU.

[First program reading analog input]

Look in the download section there is a function block for scaling Banker

[CX-Server Detected A Problem]

Hi Have tryed the same, solved by creating a new point and then run the project again. Banker