Daine

Good day. I am in need of some assitance, I have a scanner connected to my LS PLC via EIP. I am reading the data from the scanner and saving it to an array[0...31] of bytes but when I try to use the byte_String FB, it gives me an "Error L0707: The size of the array does not match. cognexIn(Row 5, Col 3)". I have attached my test code that I am using in my office. Please could I get some assistance as to what I am doing wrong? clicksMG_Enet_Test.xgwx

Good day all. I have an application which is running an Allen-Bradley SMC-Flex and the client would like to get the monitor the current of the soft-starter via an HMI connected to a Delta DVP-12SE. Is the SMC able to output a current and with what communications medium would I use?   Thanks.

My mistake. I am using Modbus TCP/IP driver with an analogue status tag. I am currently reading in a BCD from the PLC which displays in my value but I am also looking to log 2-3 tags from the same word value. I have already emailed Trihedral Support but have received a response as yet.

Good day all. Does anyone have any experience with VTScada (My first time working with this)? Looking at doing bit stripping on a word tag being read into the SCADA. Any ideas on how one would go around doing this? Can I only do this by using Scripting or is there a simpler manner in which to do this? 

I am using a CJ2M PLC with a CJ1W-MAD42 analogue card. The temperature is a is read as 0-10V signal. I tried to use a BCD add without carry instruction (+B). Problem is when I add #3(using 3°/2mins) to 40 it makes the new value 49. Which could have something to do the fact that BCD only goes up to 1001. I am going to try the binary add to see if that will work.

Hi All I have a program where I have a Solenoid Valve controlled by a Digital Output. The tricky part is getting it to heat up 1.5°C/min starting from 40°C to 100°C. I have tried to make sense of it but I am battling to figure it out. Could someone please guide as to what instructions I could possibly use?

Thanks for the Help. Got it working

Could you please elaborate?

I have done my program on the HMI but the thing that annoys me the most is that there is no Momentary Button available. Is there actually one that I have missed or what other option do have for type of application. I have 2 separate bits in my PLC which need to be triggered via the HMI but will not work without a Mometary Button. The software is NQ-Designer.

I am a bit confused about the REAL and INT you are talking about.

It is on the same program. I have one register on the HMI for the value input. It is D120

In My program, I need to increase my temperature by 1.5°C/min over a period of 30 minutes. I have tried to insert the 1.5 from my HMI but I am not very successful. Please can I get some assistance with this?

For those of you that have had a look at the setup off my MAD-42 in the IO Table. Is my Input 2 setup correctly for 4-20mA

I have managed to get the Output working, eventually. My other issue. Input 2, constantly bounces in value. Possibility of faulty sensor as I goes no higher than 5mA. I am trying with a 0-10V Pressure sensor now but it goes all the way to 14.18V. I can not remember my voltage divider circuits in order to 0-14.18V to 0-10V. Please help.

Here is the actual Program. Please don't be to overly critical. First time writing code with Omron and self taught. The value of the output is in the Analogue sub-section of the code. It is speed output and the machine only does like a max of 10rpm and that's only at the end of the program. Also not to sure if I did my scaling correctly for both Input 2 and Output 1. My Input 1 seems to be working fine. The value that I use when in manual test comes from the HMI.PandL.cxp