MrPLC Member
  • Content count

  • Joined

  • Last visited

Community Reputation

2 Neutral

About pszczepan

  • Rank
  • Birthday 07/07/74

Contact Methods

  • Website URL http://
  • ICQ 0

Profile Information

  • Location Puszczykowo
  • Country Poland

Recent Profile Visitors

4713 profile views
  1. Hi   I am working on Alarm history display and I use Event Display for that. I faces 3 problems:   How I set width of message column - Why it is so wide on attachment Is possible to set event display history when trigger goes from OFF to ON only  ( I don't want to see when it came from ON to OFF) How I can clear Event display in offline Simulation. When I will download API to NB I can set Event history clearance, but in offline simulation ?   Thanks for clue Pawel
  2. Origin Search ORG reversal

    I have wired, configured  PLC and using ORG I have behavior: direction CCW and when proximity is ON after while I get signal from z -phase and stop and get origin.  My setup is as below. I would like to get behavior: direction CCW, when proximity is ON, change direction to CW and go back. When proximity is OFF I get signal from z -phase and I get origin. In manual there is such option - "Detection Metod" - Methd 0. - I think When i set this option drive goes CCW and even it reaches proximity it sill goes CCW until get limit sensor. What wrong I do?  
  3. Function block and INI inside

    Hi I noticed problem that I cannot use INI inside FB. It supposed to look like attachment. Whatever parameters I set CXP inidcate error
  4. High speed counter and Output ON

    I wrote - it is CP1L-E Anyway if I make code !SET 100.01 in Interrupt TASK 04,  I get output ON immediately, right?
  5. Hi, I have some code and the PLC scan is quite long 55ms. I have also  defined CTBL function with HSC 0 and when the value is reached program (Interrupt TASK 04) is executed - just SET output 100.01 (electrovalve for cutting) . My question is if when I have so long PLC scan, timing for OUTPUT 100.01 is always the same - immediately when Interrupt TASK 04 is executed or is ON after scan is done and then cutting moment is different. If timing can be different how to force OUTPUT 100.01 from  Interrupt TASK 04 not after PLC scan is done  
  6. Hi. I can get horizontal scroll, but no idea how to get vertical scroll if I have more events than event window has rows. thanks for clue
  7. Hi in one PC I have version 9.6 and there is no error in line:    active_prog[hMI_Proces[proces_NO]-1]:=TRUE; but in version 9.7 in this line I get error:   ERROR: Line 115:  Invalid array index CXP doesn't accept number "-1" in the brackets []. Even I set "+0" I get the same error. For me it is bug.           
  8. Hi, I need to connect to old PLC PS32.  I have old PC with DOS nad Sucosoft S30 software and I connected to PS 3 with success. I have problem with connection to PS32. My question are? - for PS32 and PS316 I can use the same software Sucosoft S30  Sucos PS3 - V2.3 17.9.1993 ( suitable with CPU soft from ver. 1.0)  or different? - communication adapter for PS32 is different than for PS 3 and it has socket for external 5VDC. Do I need to use it to connect PC-PLC 1:1? - Communication card in PS32 - EB370.1 has 2 ports RS485 ( 0,1). To connect to PC I can use both or only f.e. "port 0"?   Thanks for clue how to establish connection          
  9. HSC, new interrupt after Z-phase reset

    linked threads are just for beginner. This is clear for me. I tested some solution and it more less works. Now I have A531.00 set to ON and hardware signal Z-phase reset encoder  I checked that if I want to start counting pulses to target value for CTBL and get another interrupt output ON I have to initiate CTBL once again after encoder reset The problem is timing. I set new CTBL declaration when Z-phase signal (0.04) goes off - but I make it from ladder and cycle is 7.3ms. How I have to implement this to avoid delay from cycle time thanks in advance    I tried to set CTBL in subroutine (interrupt task 141) from Interrupt in direct mode ( CIO 0.05). My idea was to connect Z-phase to CIO0.04 ( encoder reset) and CIO0.05 - CTBL registration), but in such a configuration CTBL doesn't work 
  10. Hi, I have encoder and count pulses in mode "Differential Phase Input" - Linear mode Every one turn I have Z-phase reset and counter starts from 0 I set some target value comparison table from D1000 for @CTBL #0000 #0000 D1000  and it works just one to reach target value   After PLC start and HSC reach target value for Interrupt 01 I get subroutine working, but even I reset HSC using Z-phase signal and PV goes to 0 still interrupt is activated. I would like to start and stop interrupt during one turn of encoder and make it every one turn Thanks for clue       
  11. SLC5/03 download program question

    I think so also. The question is, if I have memory installed is there any way to write program modification permanently? 
  12. Hi I am not very familiar with AB, but recently I decided to add some change to original program and after changes I made offline I downloaded  program and it went without any problem. PLC worked with new program until it was powered. When I switch OFF and ON power supply original program came and my changes disapper . Is it normal behavior? Can I change sth in configuratiopn to write my program permanently?   thanks for clue    
  13. CJ2M-CPU35 interrupt inputs

    Hi  In my PLC settings I have tab I/O module, there I can set interrupt inputs. There is no info if I have to add some hardware to do that or not Can you explain that.  I think I need CJ1W-INT01 added on left of CPU, but is not clear thanks      
  14. Modbus frame sent to slave - strange size

    I sent some frame from multiway as I attached and I got some reply but strange is that I get reply only if I sent frame and exktra "0000". If I send just a frame I get no response. I already sent some question to device producer, but not yet answer - just reply that device support standard modbus RTU Maybe you could explain that "0000",     
  15. Hi, I want to sent simply frame using FB mady by JPV from Omron France. It should send just frame  01030FA60002273C  to slave #1 When I check Multiway - it seems that frame is OK, but slave no reply. I checked different soft to monitor serial port and frame looks different - some bytes are sent twice.  I attached   screenshot and you can see the difference - Can you explain why it happened. Both frame I got when I set W30.0 in PLC and I saw just one blink LED Hmm I also attached screenshot from my serail port configuration. I tried also diiferent set of CP1W-CIF11 dip switches, but the same effect. Any clue??? thanks in advance