Quant
MrPLC Member-
Content count
147 -
Joined
-
Last visited
Content Type
Profiles
Forums
Downloads
Calendar
Everything posted by Quant
-
Quantum 140 NOE771 00/01 Fault
Quant replied to AP7311's topic in Modicon / Telemecanique / Schneider Electric
In case Appl LED is on the crash log is available for download from NOE card. After that the APPL LED will go off. The crash log can by analysed by SE. -
Quantum 140 NOE771 00/01 Communications with Dual Port Client Device
Quant replied to AP7311's topic in Modicon / Telemecanique / Schneider Electric
As I know the Quantum can handle up to 6 communication modules at the same time, so all NOE modules should work in the same. It's not even possible to disable the NOE in operational mode - such option doesn't exist. You should check the PLC status - RUN PRIMARY, RUN OFFLINE or RUN HSBY - depend on this the behavior of NOE is different. The NOE in PRIMARY rack should run normally with their IP addresses, the NOE in OFFLINE rack will not communicate, the NOE in HSBY rack switch their IP addresses to IP+1. -
CPU311_10 Locked Out
Quant replied to Joe_Malter's topic in Modicon / Telemecanique / Schneider Electric
Hello, how will you access the controller and see the code without having the UnityPro software? Maybe the NOE7701 Web access was protected by password, but it does not prevent access to the code by using UnityPro, if the upload information was loaded to the PLC. -
How to Transfer Control Expert EDS files (DTM Catalog Files) to Another Computer ?
Quant replied to SillyBoy's topic in Modicon / Telemecanique / Schneider Electric
Hi SillyBoy, you just need to import the EDS file (text file). Just check this video: https://www.youtube.com/watch?v=zz78qkWjRIc&t=13s&ab_channel=SchneiderElectric -
Unity Pro XL v7.0 - Where to find?
Quant replied to Eradicated's topic in Modicon / Telemecanique / Schneider Electric
just ask SE support for UnityPro v7 TRIAL and you will get download link -
Ethernet IP communication between Schneider M580 and Honeywell ControlEdge UOC.
Quant replied to SillyBoy's topic in Modicon / Telemecanique / Schneider Electric
Hi SillyBoy, in case the m580 is the ethernet IP "master" you will need the EDS file for Honeywell PLC. The EDS file needs to be imported in to the UnityPro/Control Epert software - see youtube video: https://youtu.be/zz78qkWjRIc -
uploading from Schneider 140 CPU 113 02
Quant replied to santiago's topic in Modicon / Telemecanique / Schneider Electric
Hi, to upload the application you will need Modsoft, Concept XL, Proworx NXT or Proworx32 software. -
How to use the Write_Var
Quant replied to Jarome's topic in Modicon / Telemecanique / Schneider Electric
try this: -
TSX AEY414 Problem
Quant replied to Shomation's topic in Modicon / Telemecanique / Schneider Electric
Hello Shomation, try to check if your module works in other rack or other slot of the rack - may be the slot of your rack just defect. -
In your screenshot on the right side in the channel properties choose the IP source address of your PC, then you will be able to go online. And the thernet/ip should be activated for the M580 plc.
-
anybody who may read out telemecanique cartridge
Quant replied to stefanfd's topic in Modicon / Telemecanique / Schneider Electric
Hi Stefan, try to reach the SE industrial automation service in germany, they have such old equipment for TSX47. -
Yes, the software is not for free. But you can ask SE for TRIAL version (14 days) and use it for upload/download of application.
-
if you really switched off the PLC to change the battery and the application was not saved on memory card or in flash, then it was big mistake :(
-
Up-grade Premium to M580
Quant replied to sandy201684's topic in Modicon / Telemecanique / Schneider Electric
You need admin rights to update the DTM -
Proworx32 and Remote Rack Power supplies
Quant replied to ltmartin's topic in Modicon / Telemecanique / Schneider Electric
Hi Itmartin, you need to open our Proworx application and replace old power supplies with new one. So your hardware configuration in the application should match the existing hardware and then rebuild the application. After that the error will disappear. -
Connection Between Two RIO panels
Quant replied to Tech Ahmed's topic in Modicon / Telemecanique / Schneider Electric
Hello Ahmed, you can place BMXNRP0200 module in every empty slot - it doesn't matter, due to this modules haven't backplane connectors. Use ETH2/ETH3 connectors on the CRA to interconnect CRA and NRP modules. You will find all this info in the following document: https://www.se.com/us/en/download/document/HRB62666/ -
Hi, just use PRINT_CHAR block to send any data via serial interface. You will find example in the description of this block.
-
Hi, sure you can turn off the M580 plc and replace the DRA card. Then turn on the plc and it will starts normally. In case you set the cold start of the PLC - the PLC will lost all current values and load the initial values. You can also remove connector from DRA card during PLC is in RUN. Then replace the DRA card and put the connector back without to stop or turn off the PLC.
-
Unity pro Upload simple question
Quant replied to PLC...GUY's topic in Modicon / Telemecanique / Schneider Electric
you can upload the application plc->pc any time without to interrupt the process or need to stop the plc. -
how to move an byte of int on unity pro m580
Quant replied to carretto's topic in Modicon / Telemecanique / Schneider Electric
Hi, caretto, this should work, but I'm sure you are doing something wrong :) -
M241 - Modbus TCP - problema reading analog inputs (#300001)
Quant replied to horvatmiha's topic in Modicon / Telemecanique / Schneider Electric
Hi, I'm not familar with Somachine. Your analog input module uses addresses %IW2-%IW5, but you try to read %IW1 (30001). -
Unity Pro XL 13.0 Required CPU Reference Missing
Quant replied to JustinDL's topic in Modicon / Telemecanique / Schneider Electric
Hi Justin, firmware version v2.70 exists since UnityPro v13.1, so you need the newer software version. -
plc modicon PC-E984-265
Quant replied to Ing. celestino's topic in Modicon / Telemecanique / Schneider Electric
bin_files.7z -
plc modicon PC-E984-265
Quant replied to Ing. celestino's topic in Modicon / Telemecanique / Schneider Electric
Hello MR. Celestino, are you sure that you need this version of file? - this firmware is about 20 years old. I have CTSXV103.bin and CTSXV105.bin files. -
Momentum connection issues
Quant replied to Cgrassl123's topic in Modicon / Telemecanique / Schneider Electric
Please post the wireshark. May be someone has entered 0.0.0.0 as IP address, that's why you also see zeros in wireshark.