ahsan1820

I am confused that either i can use  FX2NC-ENET-ADP adapter or  FX1N-CNV-BD wit m FX 1n plc or should i use both for collecting my data to PC 

I would like to ask is that  OC 222 output module is compatible with CQM1 PLC.  I kknow that it is compatible with CQM1H PLC. 

Hi, I have a PC which is ONLINE with my s7-400 PLC all I need isto read some PLC INPUTs and send their values on other PC via internet or WIFI please tell me how to do this.

Thank you friends for your help ,I have tried Both Methods and working fine. By the way what is the Purpose of FONT file in panel view.

Dear the usb method is comparitively easy. Does the original file .mer remain as it is on panel view after copying it on usb? Please tell me steps to make backup via usb.

Thanks I just want to make backup of my panel view 600+ using its ethernet port which is not configured yet. now I am going to perform following steps . please tell me if I am wrong. 1. Go to main configuration Screen of panel view plus 2. Terminal Settings>Networks & Communications>Network Connections>Network Adaptors>Built In Ethernet Controller 3. Press IP Address button ,IP same as your PC except the last number 4. Subnet mask same as your PC 5. Gateway leave it as default (0.0.0.0) 6. Reset your panel view. 7. Open "ME transfer utility" go to "upload" tab. 8. Select Source storage type;click on your device detected by ethernet driver,select the source location of your .mer file in terminal. 9. Browse source file 10. Name destination folder. 11. select Ethernet driver and execute UPLOAD. one thing I want to ask is that will this Ethernet IP only use for uploading/downloading or I can use it for communicating HMI panel with PLC.

My Panel view's ethernet port is not configured with any IP address as in picture but only serial DH485, now please tell me weather I can configured it directly from panel view communication settings via configure driver or I have to reprogram its TARGET tab via RS view studio.? And one more thing if there is any problem if i done two TARGET configurations at the same time like DH485 and ethernet .? If I upload program will it give me a copy or original file itself.?

As I named the attached picture " FX 1s 30 MT " and no I didn't changed the parity/stop bit settings. By the way I have tried communication on all baud rates

yes i have the address COM1 when i connect my usb cable..

i also have self made SC 09 cable but it is creating problem with one of my PLC to communicate and gives the following error. FX 1s 30 MT.bmp

I have chinese made usb sc09 cable .Installed the driver and assigned the same comm port number to the GX developer as I have in hardware manager after installing the driver but on each and every baud rate in the Transfer setup it gives me the same error as attached in the picture usb cable error.bmp

Thanks A lot, I will check version while turning ON

Dear, please tell me 1) How to see version of E200 Mitsubishi HMI? 2) Is there any need of going into any transfer menu in the HMI or it can be upload simply from E-designer tool via receive option? 3) CAB5 cable for RS 232 communication has the following connections or some thing else please mention? CAB5 DB9 female DB9 female 2-----------------------------3 3-----------------------------2 5-----------------------------5

I know how to upload pgm via gx developer. but please tell me the purpose of uploading "device memory" option. I have to make just backup of program so that I can use it in case of PLC failure. what role device memory play ,why should it in uploading menu.

Dear, I have to communicate my SLC 5/04 CPU channel0 ,configured as DH485, i have an ethernet interface 1761 NET ENIW. I have read how to configure this 1761 NET ENIW via PC comm port ,using ENIW configuration utility. I want to communicate in the following manner PC ethernet port to ENIW ethernet port using ethernet cross over cable and RS 232 port to SLC channel0(configured as DH485) via a 1761-CBL-PM02 series C cable. But please tell me if there will b any issue with channel 0 of slc is configured as DH485 and ENIW has rs 232 port.