tintin2005

Hello Jay.   Thanks for the link. D2 and C11 have no value.  Can you or anybody help?   Kind regards

Hi Again.   Thank you.  i found this link that explains the cable needed VS Plc. i posted it because i think it is very usefull. ragards

Hi Jay. You are Super.... thanks.   And with this one is it possible? it is the omron original   9 pin db9 and omron 20 pin with the interface box.   thanks!    

Hello !   Can i connect to c20h controller  with cable attached?   i have the serial port connected to a nt20 and i need to go online without disconnecting nt20. is it possible? thanks

hi.   i know that this post is quite old but i am looking for the cable schematic and i can´t find it . Can somebody post the shematic, please?   regards   tintin2005

Hi! I know that this thread is quite old but can you help me? Is the software still available?   regards

Hi again. Already have done all the changes and connections but still don´t work. Regards from pT tintin2005

Hello Man. thank you for your fast reply. There are only 7 wires connected? pins 5 and 6 have no connection..... is this right? thnks in advance tintin2005

Hello. I am trying to conect to a CPM1A-40CDR-A-V1 omron plc with CQM1-CIF02 original used cable. As he as a db9 male i adapted it to a db9 female folowing this diagram: http://forums.mrplc.com/uploads/monthly_02_2010/post-2041-1266502872.png but my cable´s db9 as some strange conections as you can see in attached photos. i think that this cable was used to connect some omron plc to a printer orto a NT20 hmi. probable someone changed the conections. pins 4 and 5 should be conected but as you can see there´s no wires connecting them. ad there´s some cutted wires... My cqm1-cif02 seems to have this connections ... http://forums.mrplc.com/index.php?app=core&module=attach&section=attach&attach_id=9960. Has anybody got the colours to pin number? Can someone open a good working cable and share the connectiosn info? Some help would be NICE! regards tintin2005

hello guys. Let me say that i am a beginer in this stuff.... I had a magelis xbt f032110 that was comunicating with a tsx 3721 (Micro) and it got broked . As those magelis are obsolete i converted the app with switch2vijeo to adapt it to xbtgt 2220. Because i don´t have a xbtgt2220 i changed the target device to xbt gt2330. i have corrected the conversion errors and creat the new cfcard project. i made the comunication cable XBTZ9780. the plc is working with unitelway protocol and worked fine with the old xbtf032110. Now it always says " No reply from PLC within Timeout period. (UniTelwayEquipment01)" Can anyone help me to make the correct tunning for the unitelway comunication? regards tintin2005

Thank you Jay. I will test it later and leave a feedback. I will try with syswin 3.4. thnak you for your help. tintin2005

hello jay. thanks for your fast answer. I´m going to make the cable and try again. Do i need this 3G2A6_LK201? or it´s direct to Personal computer? The LSS and SSS dos software available here in the forum has full working capabilities? regards tintin2005

Hello there. I need to download the application from a Omron C20H plc and have already tried with severeal cables, but had no success. Is it possible to do it with a simple hand made cable, or i need to use this intergace 3g2a6-lk201-ev1? I read somewhere that i could comunicate with C20H with a simple cable. By the way, with hand made one i did receive some errors, but now i do not have here the printscreens that i made. later i will put them here and i hope that somebody wil help me. regards From pT tintin2005