Georgios
MrPLC Member-
Content count
23 -
Joined
-
Last visited
Content Type
Profiles
Forums
Downloads
Calendar
Everything posted by Georgios
-
maybe you can check for hardware error with PLC diagnostics function?
-
Hi, I ve been thinking of connecting two FX3G plcs and an HMI on a local Ethernet, which ethernet adapter is reccommended for FX3G? Thanks for reading! Regards, Georgios
-
Remote I/O module (CC-link) on GX IEC Developer
Georgios replied to kwnstantinos's topic in Mitsubishi
Just use the 8 Inputs not the outputs, u can also use just the 8 bits of the 16bits RemoteInput -
Remote I/O module (CC-link) on GX IEC Developer
Georgios replied to kwnstantinos's topic in Mitsubishi
Hello Constantinos, I think you have to use an FB named " RemoteInOut_8Bit " All the best! -
I have problems with Q usb drivers for Windows 7 with 64bit processor, is there Mitsubishi support for Windows 7 ?
-
Also, if you remove from the rack this module you should see DIP switches on the side (node settings)
-
If you want to program your PLC remotely, at first you need to establish connection (PSTN,ISDN,Internet,..) between your programming platform and your PLC. eg You could connect a serial modem with 232port of 1101, connect local and remote modem, and use transparent mode to program your PLC
-
Thank you for assistance, i ll try these new FBs!
-
Hello everybody, Has anybody experienced multiple Q UDE data exchange? Moreover, can i exchange data (fixed buffer) over Ethernet between eg three Q03UDE using only a common switch (no hmi, no scada), built-in Ethernet ports, and cheap CAT5 cable ? Thanks
-
Thank you, it looks to me that it is not possible to exchange data between 2 or more UDEs, better use something like Qm CPU and QJ71 ethernet module
-
Thanks for the reply, However, i am sure there is nothing wrong with my national SMS provider number because when i replace FX3U and i connect Alpha XL to GM106 my system is working as expected. I claim there is something wrong with hardware. Did anybody make FX3U and GM106 communicate? Regards
-
Has anybody make work FX3U and GM106? I am doing what manual says, but it looks like there is no communication between GM106 and FX3U (when i change modem to FX1N there is no problem. Any hint is welcome. Thank you!
-
Hello! Simultaneous broadcasting using UDP protocol on Q systems is working and performs very well! I don't know about the performance of other configurations. Hope the best for your system!
-
--This configuration is working, want to try? 3U_ENET.rar
-
MX Component 3.13 includes FX3U choice. FX3U driver is the same with FX2N only in theory. In practice i changed an old FX2N with FX3U, i had no com error, but i had no alarms transfer from PLC to HMI. Then i had to update HMI serial driver and my system was fine. Good luck
-
Would you consider adding a GSM modem to your configuration and connect it through RS232 to E410 ?
-
Do you mean my provider's data are wrong? I did use the same settings for a job with Alpha XL - GM106, and worked fine.
-
I am sending my files for your review. At this moment: -I can see modem initializing ( Data out LED lights for 1-2 sec after restart ) -I can see GSM network ( Green (Line) Led flashes every 5sec approximately ) -When Y0 changes , I get nothing changing, no sms, no process LED, no Data out LED. I am using SC09 to connect FX3U programming port, and a gender changer to connect to GM106 Modem's port. Can you see the error? Thanks again GM106_FX3U.rar
-
Using counters / SPD_M funtion maybe for rotational speed ?
Georgios replied to BenJones's topic in Mitsubishi
-
- There is no standard cable for this job, can't you get a 232 port on GOT side and use standard cable?
-
I’ve come up with a work around for the compare function. If drop a up down counter function into the program which I don’t attach any inputs to. I then feed the current count word output into the compare input. The strange thing is it does let me write to this current counter value by mapping this to a CW word which I can then address in the HMI. - I also use UP/DOWN counters to create set points and compare function for temperature alarms. The only way I've found to set a bit from the HMI is to drop a link output into my alpha program and then address it directly from the HMI using A01. But there is only A01 to A04 to use so fairly limited. I think I'm going to have to use a word for each bit using the previous method. This can't be right. I've been on the phone to Misti support in the UK and they were not very helpful.