GixRamones

Hi. SF= mean Error hardware o software You must find the error! Check the source power of module. In the last on Simatic manager press Contr+D for Diagnostic on line. bye

Hi. in usual with Siemens have different ways, choice is yours! Link to siemens Important the CPU must have the clock. Example, the cpu 312 has no clock, and KTP (I think also it has not clock buffered from battery), in this case (cpu312 + KTP) you are not be able to get what you want from the system. bye

Hi. Is the old history of siemens and MSB-LSB especially on alarms, sometime alarms pointer walk-out way me. The best solution WinCC Fexible 2008. In WinCC Flexible 2008 in the alarm message magically appears with a column addressing that takes (DB80.dbx1.0 | "My message "..|..| etc) then it becomes easier not to make mistakes. Strange I wondered why this feature had ProTool and WinCC no, confess that by 2007 on a complex project I wrote in ProTool alarms and then imporai in the project. bye

Hi. There are several ways to active one or more alarms in one or more pages. This, however, mixes a little message. still draws a blank page. 1) Made a new page, take a view Allarm under tool exension put it on the page. 2) go to variables creates a variable word called Pt_Segn es Mw80 cycles continue element array 1 3) add digital records management reporting allarm. When the bit is m80.o log on to the page and the alert appears. Alternatively you can use the system page that you find in the system model page. M80.0 when goes to 0, the signal is removed. Attention in MD80 the 2 Mw turn (MSB-LSB) Read the online help and search for examples from Siemens bye Mmm forget which Panel

Hi. Time ago I used standar Fc. From library\IEC fc38 from string to 16 bit. fc37 from string to 32 bit. fc39 from string real 32 bit. bye

Hi. But in the simatic manager query nodes accessible something anserw. if nobody anserw, and the led blink in the same time maybe you have problem with MMC before consulting Here Only if you are sure the MMC is Fault you can try to formatted it. ....I don't remenber about 'ram memory failure' never see it.... bye

Hi. I don't remenber but I suggest you also check the hardware connection, special about ground 232, standar is pin 5 but omron maybe is 9. compare the 2 connection. bye

Hi. Start from link. There are some example but you must found the manual about SFC. If in your S7 Manager put SFC51 after pres F1 and help online show up. Siemens support Bye Forget. If you want know the value of scan time of plc write this code in OB1 L #OB1_MIN_CYCLE // LW6 T MW250 L #OB1_MAX_CYCLE // LW8 T MW252 L #OB1_PREV_CYCLE // LW10 T MW254 Value in mSec. The register are in Temp of ob1 bye again.

Hi. I would also do this, now I'm not need it. I'am stop in reading the manual and some test. looks about the SFC 51 "RDSYSST" extraction lists. Normaly I use SFC51 for read the Dp State and this way is good good luck. bye

Hi. with some way for both object. 1------- 1) declare Tag 2) draw obj 3)Go into panel property when the obj is select. 4)Look about animation (Visible, enabled, etc) 5)link here the tag 6)Select Type bool 2---------- Look also button property format of button bye

Hi. ...Ram.. maybe but maybe the problem is there. maybe but maybe you need compression memory. Have you some news about cpu error message?! is importat! before compression memory. The Battery is good? Have you some back-up?. Some digital output are in on state? bye

hi. Is very hard! What are in upper slot? Have you some RAM or EPROM or EEPRON (in slot in up) ?. Best way (for me in the first) is connect whit PG/pc Station and see with software the message code. There are some table with acronym message after see the manual to relate the acronym message. Then if you want to post here the message error ! bye

Hi. Have you the sfc51 on S7 manager? focus on it and press F1 (help) Through the partial list with id # W SZL 16xy11 show the identification of a particular unit. The header of SZL SZL ID W # 16 # xy11 is structured as follows: etc.. Now in your Attached File, you ask to Cpu SZL_ID= 119. Why? 119 which Cpu you use. The Sfc51 is a function is strong. You must in input call which list and which index e it come back the Struct of list and PointerAny or Len of struct. If is the first time that you use it, is better monitor the retVal for help. Esemple: #INDEX = 1, #SZL_iD =W#16#692 Ask to cpu the state of node profibus It come bak ine struct of 16 Byte where the first 32 bit are the curret status Fault About the node profibus. Each list and each index return data and different struct. Bye

The OB= are block organizational. Do not have to configure! but to manage with the code within them. The battery was used on the old cpu is not new. Iside of Ob to put on a Merker that the rest of the program calls. Es. for low battery warning -- In OB81 set M110.0 = / / Low Battery -- For other Ob 80 Cycle Time Fault, OB82 Perif Error, Error Rack..etc. There some Obxx also with schedule. Read the manual for choose the most suitable to you. Anyway, I use the block function SFC51 RDSYSST through lists that tells you everything about led, of local or remote Fault, hardware information construction plc , information about patner in profibus.. etc. .. Bye.

Hi. I'm away for work and I don't have WinCC on this Pc for example or debug VbCode! Have you read the suuport servce page?, I think you can strat fom this Link put this number '27039111' in field advanced search. Bye