nguyenthucuc

Dear everyone, I would like connect Bar-code Reader to GOT that read Bar-code to input data on GOT 1575 VNTB Note: Barcode Reader is symbol model & I have use Power electric 5V to nourish And, I would like confirm that have conflict reverse electric  from Bar-code Reader to GOT or not? Thanks so much

Dear All, I'm trying connect Barcode USB to HMI that read content via Barcode. However, I only read 1 times after installing HMI program although clear bits reading. Who have experience about this, could you share your experience to process it. Note: My barcode has 10 characters Thanks so much! TEST-1.GTX

Dear all, I'm study GOT1000 (but old Touch panel). Now, I have the system that already exits: GOT (F940GOT-LWD) ---> PLC: FX2N-48MR and, I would like expand this system that will connect with computer (PC) to get information form Touch panel & PLC PC ===> GOT ===> PLC However, I don't know the method which would use in here. so, I would like question to do it. 1. Can I connect PC & GOT using Ethernet or not? 2. (If have) How to do it/ I neet add new device or not? Thanks so much!

Hi all, I have project and I saved as compressed file. But, I open in other PC again, it can't open and alarm as image attach. If any person have same problem and have solve, pls share it for me. Thanks and best regards!

Hello Dears, I am studying to control position via Mitsubishi device Now, I have Q172 CPUN and MR-J2M(MelServo) to control position. But, I didn't find manual that explain command and parameter to do it and it has the example to do it. who have experience to control position, pls help me to overview it. Thanks so much!

Thanks Crossbow, I also finding and study about it, but not really clear about it. Do you have  MT Developer  software and can you share it for me  

Thanks so much Sparky I will try study more in documentation If I find the method, I will share for you and who person have experience about this, pls help me to solve this problem.

Dear all, I have GT1565-VNTB, But suddenly, it's reverse content and position of touch is don't change. It's difficult to control its. Now, I'm want to change it to normal. Who know about this case? Can you help me to do it?

Thank you Sparky I looking for your information.

Thanks you for your rely However, I already try as your comment, but it's not ok. I would like add more information as below. 1. I already reboot OS of Touch panel and install again 2. Image display as below. 3. Alarm: 481 Communication unit not mounted to the slot of active channel ==> I think this alarm because I've not yet connect with PLC If you have other comment, please share it for me.

Hi, Actually, you don't need convert and you can open with GT3 But, you need load file from your device and save it as compress type.

Hi Ianreeves Did you have connect GOT with PLC? Did you select option: Read directly input to object? If you select Yes ==> You don't need setup address in here, but you need setup mode input data for address. If you select No ==> you must be setup in system information to reset flag via Barcode reader (bit 6)

Dear Sirs and Madam, I'm want to read data from CF Card in GOT via FTP from PC. I have done it with GT15. However, I add CF Card to GT16 VNTB and can't access file in CF Card as below image Who person have experience about it, May you help me? Thanks so much!

Thanks for your support. But, I have more confuse in this documentation: (1)- Documentation only raise GOT-A900 Series and GOT-F900 Series. So, Should I do GOT1000 as GOT-A900 or GOT-F9000? (2)- Do I read/Write data from GD Device? Because I only see Virtual for D, R, M, SD ... not GD,GB. Ref: Documentaion: sh080532engq.pdf ==> Page: 1282

Dear Sirs/Madams, I am studying to connect between GOT1565 and Microcomputer/PC via RS232 However, I only see the documentation for GT-A900 and GT-F900 So, I'm wan to ask you: Can GT1565 connect with Microcomputer/PC via RS232? Who did it? can you help me? Thanks so much!

Excuse me! who have experience do it, please share it for us?

Hello everybody, I also need to connect Barcode Reader to GT16 1) Barcode Reader RS-232, I have already set-up I used Multiway (software) to check it, and receipt data as image below: 2) GT16: I also installed as attach file. However, It can't display data in GT16, Who has the experience about this solution, pls help me to revise it. Thanks so much. GT16-Barcode.zip

Dear all, Now, I would like connect Barcode Reader and GOT1662-VNBA. Normally, we can connect barcode Reader to GOT1000 via RS232. However, I find 1 USB Port infont, so has a question: Can I connect Barrcode Reader and GOT1662 via this port? http://www.mitsubishi-automation.com/products/hmi_product.php?id=64&__= Thanks so much!

I saw Thanks so much Crossbow.

Thanks Crossbow, I knew that it's old type. So, I want to ask: We can add more module for it that help its can connect to PC via Ethernet (Example GOT1000, we will add FNB Card and Ethernet Module)

Hi Crossbow, Thanks so much!

Yes, My email: amateur.plc.hut@gmail.com

Thanks all for your rely! USB Port that I raise in here is USB Port Normal (not USB mini-B plug). And, as your idea, we can connect Barcode reader with GT16 via this port. but, I can't enable this port in GT3 in the GT16 as image below. Therefore, I would like more question: How to enable this port to connect Barcode reader and GT16? Thanks so much again,

Thanks so much. I've already setup.

Dear all, I'm building the system that include: Sensor --- > GT16*** --- > PC (GT*** --> Touch panel of Mitsubishi: GT1662-VNBA) Target: - Sensor send information to GT16 and GT16 will store this data to file (csv/txt) by time. - PC will connect to GT16 via ftp and copy file from GT to PC. about connection from PC to GT16 via FTP protocol is normal (as manual) and I don't know, how to write data from Internal Device to file (target_1)??? Do you know about this setup? can share it for me! Thanks so much!