electron

Hi PMCR, Thank you for the thought, from your experience i made conclusion, that highspeed speed control still can't use communication for now Best Regards,

Hello Omron Modbus Gurus, i'm on the way to selecting drive inverter directly or using communication ussually we drivin inverter direct thru analog output, but using analog for controlling a mass of inverter (around 18) will take high cost, while using communication offering lower cost and lot of usefull status now since more fast communication become possible, this thought emerge again, would control from modbus (protocol macro using SCU31) fast enough compared to direct analog control ? best regards for your experience and knowledges sight

Thank you Chris, i'd download the pdf, but can't found a list of plc supported in it

Dear Mitsubishi Gurus, Please advice, i will convert mitsubishi plc A2A CPU S1 to latest version, what is the best replacement for this type ? also will buy latest version of gx developer, but i not sure wether latest software version still suport old A2A CPUS1 ? do i need gx iec dev.? Regards,

no can do. normal choice is upgrade license to 10

Seem the application too heavy for the processor, many times i use cx simulator from cx one 3.5 , on dual-core processor 1.7Ghz when running a big application , the simulator stop or said it can communicate with virtual plc if reduce as much as possible other application that running not show good result, than you should overclock the PC or use a fater one

my opinion is, every works has it own class, no works is unused in this world keep on the good working if you will create, that's ok, if you will buy, that's ok, every thing has it own risk if you want to steal, well that's NOT ok

don't check option "load expanction function" actually you last upload was success question mark and NOP funtion is a prove that the application is error, you need to fix the missing program and download or create new application

Hi Crossbow, FX-PCS/WIN is it year 2010 version of FX-PCS ? if just equal, then which one better GX Works2 or Gx Developer -FX ? (or is GX IEC Developer FX, if exist?)Regards

Hi All, i'll start to use FX series, but confused which software to use, FX-PCS/WIn or GX-Developer for FX , since both full support FX, i'll chose cheaper FX-PCS, but now i wonder what is additional function on GX-for FX ? hope you have clearer comparison here Thanks before

Hello All, Due to CTBL range comparison always error, i make change to CP1L setting, as in attached picture, fortunately now i can't even connect the cx-programmer to CP1L, using usb, toolbus (auto), sysmac way both thru port1 & port2 is there any way to reset it to factory setting ?

Hi All, I Plan to replace C200H CPU With CS1 CPU, as i know CS1 still support using old C200H analog I/O (C200H-AD002/DA002) but i can found any omron document show how to configure those C200H analog I/O in CS1. all i got is W229-E1-3 explaining C200H-AD002/DA002 unit in C200H CPU and W345-E1-05 explaining CS/CJ Analog in CS/CJ CPU. or maybe it will just simply the same as CS/CJ Analog unit configuration in CS/CJ CPU ? Regards, Electron

Hi Crossbow, Thank you for information, but you said manual is everywhere plese give me one link, i'm back here cause i'd found nothin ,also the mitsubishi people answer none to my email may be because it's too old (no value) ?? Hope i can get more here

Hi All, I 'd search to find editor,manual,wiring for old mitsubishi display terminal MTA250 but just find that there is a MTA-WIN & DOS editor for this type hopefully you are in mitsubishi forum familiar with this display know where can i find the stuff Thank in advanced

Thank you all for the information, then i can't found software for upload program, it's ok but i still need to find correct replacement for this PM 313 C2, please correct me i'm wrong : the unit is sinking output with max program not more then 2 Kword ? Thank you. the information would be vary helpfull