JD1ROSE

Looking for help locating a source for motion sensing inductive proximity switch. This will detect when a object has stopped or has dropped to a very slow speed. Have had some info in a Telemecanique brand. I have had no luck with a source. Thanks Roy. r1daros@hotmail.com

Hello guys, Below is what i'm looking for, I need the wirering for it, if someone can draw it up and e-mail it to me. r1daros@hotmail.com Thanks Roy When the pulsing stops, you want to stop the line. So wire the output of your proxy to a 'Timer ON', which will time out when the proxy stays on for too long. Also wire the proxy inverted signal to another 'Timer ON'. You might use a fast relay to invert the signal. This timer will time out when the proxy stays off for too long. Use N/C contacts on the timer outputs in series to allow the line to run. For starting up, you will need to temporarily bridge the timer outputs until things are running.

Thanks for everyones help, I need to do it with one prox switche and timers. It will be set up to make and break sence. I need help in the logic. Roy..

I need some control circuit help. I have a shaker for scrap that is used on all of our press lines. I need to detect when the shaker stops for a malfunction. I want to hook up a prox sensor that is stationary and a bracket that will move with ths shaker in and out. So it will make and break the prox sensor. If this signal stops for more then 1 minute I want it to stop the press line with a e-stop fault.I need help to come up with the hardware to create the logic. If you can help me please E-mail me at, r1daros@hotmail.com Thanks, Roy.

Thanks for the info. When I try to add a new driver, the 1747-pic is not a option. I want it to be an option, how can I get it to be an option. Thanks Roy,

Just to provide more info. My computer is running Windows 2000. I have Allen Bradley Rslogix 500, Revision 4.10.01. Using Rlinx Lite Revision 2.20.01. Com cable is a 1747 PIC. I do not have a driver for this com cable using this version of Rlinx.

Does any ony have the driversoftware for the 1747pic cable If so can you please e-mail it to me at r1daros@hotmail.com

George, I will order one of the Action Instruments, AP4380-2000 and let you know how it worked out. If you have any information on installation that maybe I should be aware of please let me know. Thanks again for your help. Roy...

AUTOMATION DIRECT SELLS A, FC-11, 4-20MA ISOLATED SIGNAL CONDITIONER. DO YOU THINK THAT THIS MODEL WILL WORK?

Do you have one that you can recomend? Where to get one? I'm not familure with a isolator for this application. Thanks Roy.

THANKS FOR YOUR VALUED TIME IN HELPING ME WITH MY PROBLEM. YES, THERE IS A DONFOSS VLT5032 DRIVE THAT GETS IT SIGNAL FROM A SY/MAX CLASS 8030 TYPE ROM-121 STANDARD ANALOG OUTPUT CARD MODULE. I THINK YOU ARE RIGHT. BUT HOW CAN I CORRECT THIS PROBLEM? WHEN THIS CUTOFF PRESS IS INCHED IS WHEN THE PROCESSOR GOES TO HALT AND THE ERROR COMES ON BUT NOT EVERY TIME. AS STATED IN PREVIOUS MESSAGE, THE TAPPER AND MAIN PRESS ARE IDLE WHEN THE CUTOFF PRESS IS INCHED.. THE LINE WILL WORK FINE IN CONTINUOUS MODE ALL 3 PIECES OF EQUIPMENT. WHEN THE CUTOFF PRESS IS INCHED THERE IS A LOAD ON THE DANFOSS DRIVE. THE DRIVE CONTROLS THE MOTOR THE DRIVES THE FLYWHEEL. THANKS AGAIN.

SOFWARE INFO CLASS 8010 TYPE SFWW-374 REVISION 1.0 OCTOBOR 10,1989 There is 3 pieces of equipment, a main press, a tapper and a cutoff press. The processor sy/max is in the tapper with some inputs and outputs that go to the main press and cut off press. When they all are running in continuos mode the line will run fine. The fault comes up when the cut off press is inching by itself. the tapper is idle and the main press is idle at that time. This is the only time the fault comes up. when the fault happens the power to the tapper processor is cycled and it will come on in run mode. t only happens sometimes not all the time. Nothing happens to the cut off press omoron processor it will stay in run mode.

I HAVE AN OLDER SQUARE D SY/MAX PLC, IT COMES UP WITH AN ERROR # 20009 I HAVE BEEN UN ABLE TO FIND THE SOURCE OF THIS ERROR. BELOW IS THE LIST OF EQUIPMENT AND THE STATUS WHEN THIS ERROR ACCRUES. IF YOU COULD PLEASE HELP SOLVE THIS PROBLEM OR YOU NEED MORE INFORMATION PLEASE E-MAIL ME AT, r1daros@hotmail.com. THANKS FOR YOUR HELP. --------------------------------------------------------------------------- MAIN I/O RACK ASSEMBLY SY/MAX CLASS 8030 TYPE HRK-200 ------------------------------------------------------------------------------ SY/MAX PROCESSOR, STATUS WHEN FAULT ACCRUES MODEL 400 RUN, LIGHT FLASHING I/O, LIGHT ON. ---------------------------------------------------------------------------------------- LOCAL REMOTE INTERFACE, STATUS WHEN FAULT ACCRUES SY/MAX CLASS 8030 TYPE CRM 210 RUN, LIGHT ON CHANEL 1 ERROR, LIGHT ON RUN, LIGHT ON CHANEL 2 MODULE ERROR ---------------------------------------------------------------------------- CLASS 8030 TYPE HRK-100 I/O RACK ASSEMBLY -------------------------------------------------------------------------- SY/MAX CLASS 8030 TYPE ROM-121 STANDARD ANALOG OUTPUT CARD MODULE RUN, LIGHT ON STATUS WHEN FAULT ACCRUES REMOTE INTERFACE SY/MAX 8030 TYPE CRM 222 HALT, LIGHT ON STATUS WHEN FAULT ACCRUES