Bill Estey

Is there a way to work on a NT 600 screen program using NS Designer/

Looking to read data from an energy meter E-Mon Class 3400 with an Ethernet Modbus TCP/IP connection does anyone have sample programming for this application

Does anyone have a way to recover a password from an Omron NP5 HMI

Yes I do but if I try and upload the project it will not let me without a password. Thanks for any help you can offer

Has anyone seen a 64 bit version of a driver for the 3G8FA-CLK21-V1

Hi I am using a CJ1M CPU13 and have an input module CJ1W-IDP01.I need to connect 3 encoders all running at apx the same speed of 16 PPS will this module work for this application.Thanks for any help with this

Hi Could anyone tell me the best way to operate a processor using a Personal computer that has its own touch screen monitor as I need to run another program on the PC but also would like to use the PC's touch screen to control my program. Thanks for any suggestions

Hi I am working on a control system that will have outputs that operate on time how can I make these outputs operate so they will not be syncronize.I want to be sure that when these turn on the load the contacts won't close at the same point in the power cycle. Thanks for any input on this question

The potential problem I am trying to overcome is having my outputs turn on a contactor at only one point of the power sine wave I would lime to have this happen at random points of the ac sine wave

Sorry for the late reply I have been away.What I am looking for is I am turning on these outputs every 3 seconds and I want to be sure they don't always turn on at the same point of the AC sine wave so every 3 seconds but with a bit of radomization.

Hi I have used PID function in the CS1 series and the CJ1 series controller I am setting up a PID control using the CQM1H-CPU51 and am having a few problems but one question is what format are both the inout word and the output word also the set value. The instructions do not mention their format only the other P1 settings. Thanks for any help

Hi Has anyone developed a slide switch control to quickly change a value using an HMI Thanks

Thanks for the reply I will have to play around with it

Hi I am trying to set up a CQM1H with a NS screen using controller link. I set up a datalink table but when I went to connect to the the PLC it did not offer the CQM1H as an option.What would I be doing wrong. Thanks for any input

I did set up routing tables but when I try and connect to the plc it doesn't give me an option for the CQM1H nor does it give me an option for CV series as tashinz had suggested. I am wondering if my CX-One is the problem I have ver 1.01 and have not had any upgrades since I can't seem to find how to do that. I may upgrade to ver 2.0 do you think that will solve the problem?

Yes that is correct

Hi Try and transfer the IO tables in Program mode if you have not done this yet

Hi Could anyone tell me if the Omron 3G8F7-CLK21-EV-1 card is compatable with Windows 2000 Thanks

Thank you for the quick response

Hi I have used many of the TS-001 and not had too many problems except erratic temperature readings I can' t seem to get a steady temperature I am reading at the upper limit of range 1550 F-1600F is ther anything that can be done to fix this problem Thanks for any help

I am using a CPM1A with a CPM1-CIF01 communication port with an NS-5 screen connected to it is there a good way to keep the screen operating and still monitor the program with CX programmer as I need to troubleshoot the program during operation

Hi I have a C200H-AD002 that I have lost the connector to it is a Honda Communications p/n MR-34LFG anybody know where to purchase these. Omron has not given me a source since i need it soon. Thanks for any help

We were able to convert the screens using an NT V4.7 Thanks for all the posts

Could anyone give me some direction in converting a 620 S to a NS-12 the existing 620 s screen is blank the run light is on but there are no screens showing and I have a NS-12 in stock. Thanks for any help