Zoran Mihajlovic

Hallo, I need to load program from old TSX nano and transfer it to my new (7 year old on stock) nano, but I lost my PL707 softwer . Can you help me or PM the softwer. Thank you very mach.

Yes, I have 2 PLC on CX-S.

You need 24VDC power on DeviceNet, give NSJ (1 for example) and V1000 (2 for example) different node addresses. In V1000 manual you find on whitch address is parameter. I use DeviceNet offen and for simple application with Omron components I don't use Cx-Integrator,only give diferent node address on slaves. In thet case input word is on adress 33xx, and output is on 32xx. Best regards

Great idea. I don't know for Omron , but Telemecanique have smol Zelio PLC thet run on 12VDC, have ocion for GSM modem,nalog inputs,calendar etc.Wisith their web for details.

Hallo, As I posted before to you, I use'd HBM on CQM1H RS232 port. For some time I didn't use HBM, and now I need to conect HBM WE2108 to CJ1M-CPU13 PLC with SCU41 card. Link is on port 2 as RS232 . I have problem with reading value (MSV), it send ok (I think) but receave is not good. COD and TARA is executing, so cabel and other is OK. Wher is mastake? HBM.zip

Wild car do everithig , it receive 12 byts in ASCII format. Thank's to you!

Thanks, B&B I will test as you say , and let you now the resalt.

E-Plan is great softver too.Price is biger but have all you need.It suport DIN,JIC,IEC and USA standard for simbols and else.

I have similar problem in my old job. Boss tell me to unsafe thing.Becouse he is boss I have to do. But I tell hem thet is unsafe acording to some rule I imagen and ask him to give me writen specifik order to do that. Becouse he consern of perhaps problem if somthing hepend he did't give me writen order , and I didn't turn odd safti switch. Maybe to do same with you boss??

Thank's beegee it help me a lot.

Hay, What is yor sugestion for inverter 0,4kV 630kW motor for extruder. I use Omron and Schneider but then don't have this power. Some advise be helpfull.Thank's

Yes, I call Omron distributer in Serbia and they say that Omron dasn't have drive beeger then 300kW,and ofer me drive of ASI Robicon. I don't like Italian product becouse bad experians with they equipment. I know thet 630kW in 400VAC is uper limit, but investitor didn't use extruder with 500kW as I sugest. This mashin - motor is at my opinion overrated and motor will work ,as I asume , at 60-70% off full power. I'm in contact with Control Technique for drive,and some other manufacturer.Some sugestion will be good. Thank's to all!

It's HEX 1A. Go in download Code and find example thet Sleepy make, it's excelent for starting.

Mybe some ideas. If you can measeure voltag on potenciometer bitvin pin 8 and 10. It mast bee steade at 10V. How old is drive thet is replaced, ther is some problem with elektrolit if it's older then 10 year.If so tray to replace it with new, I have some result with this.

On the table is 2m.And on site is 80-90m.

From my expiriance new model of NT2S don't work with old NT2ST. You need NTXS for transferinf firmware first to NT and then application. I hve one recentli and can't work with NT2ST becouse it wont too connect to NT.After use NTXS and transfer firmvare it work and receave program from NTXS,but won't work with NT2ST at ol. So it's neseseri to use NTXS. I houp it help's.

Well, Meybe it is pure luck, but I work with protokol for V7 inverter , and CJ1M-CPU11 ver 1.3 CJ1W-SCU41-V1 ver 1.3 and use RS485 mod.

It work at 115k on site.

Access fild by index in Modify field association dialog.

Hi too all, I have similar setup in one factori with CJ PLC and ETN21 thet is conected too factori ruter and gays thet do networ set me ruter too have acess fro any place in faktori ethernet place.It is wheri easi too put this ruter on ther internet accese nad to enable me accese from my office over internet. In PLC ETN I did onli basic seting as you can see.

Pawel Her is manual for programing HBM2108 with RS232 port, I houp it helps. ba_we2108_pc_e.pdf

Ok Pawel, I glade my example help you.It work's on several mashin. Data format for HBM komand is all in ASCI, so the value thet move is ASCI. In Programing manual at the end in appendix you find table with values for convertin to ASCI. I need some time too find elevtronic manual for HBM 2108 weight modul and sand to you,but maybe is on their internet too. Best regards.

Her is example for CQM1H and HBM wight modul 2108 CQM1H_HBM2108.cxp maybe help's

I attempt to do the same seting in my CX-I and didn't work. I recevi wornig then ther is mismetch in ocupaed data. So mybe is problem thet Master DRM21 use 4 byte for inut and 4 byte for output, and you wont 8 byte for inut and 6 byte for output. Whay don't use default automatic seting - Auto Connection, I think thet in FB for inverter say thet default seting is too be use. I mast say thet don't have experience with inverter on DeviceNet, but do a lot off projects with other moduls and olveis use default seting. Sory for my bad english writing.

ebalan Whwt type off number (PLC memori aray) , and with whitch device - CX-P in online, terminal or PC.We need more informacion.