adriano_pedro

MrPLC Member
  • Content count

    7
  • Joined

  • Last visited

Community Reputation

0 Neutral

About adriano_pedro

  • Rank
    Newbie

Profile Information

  • Country Portugal
  1. Cpm1a - Mad01 Configuration?

    Hello, Thank you for the reply... Could you verify the file that I'm sending (prog030206vs3.cxp)? To see if it is according to what you told me? I think problem is getting more close to the solution, but.... I also send another program that I've been trying... Thank you, Regards, Adriano Pedro Prog030206vs3.cxp Prog060206vs2.cxp
  2. Cpm1a - Mad01 Configuration?

    As default it is: SW1-1 OFF SW1-2 OFF SW1-3 ON SW1-4 ON SW1-5 OFF Therefore it's expecting a 0-10vdc signal --------------------------------------------------- If needed... For a 0-20 mA: SW1-1 ON SW1-2 ON SW1-3 ON SW1-4 ON SW1-5 OFF For a 4-20 mA: SW1-1 ON SW1-2 ON SW1-3 OFF SW1-4 OFF SW1-5 ON Thank you, Adriano Pedro
  3. Cpm1a - Mad01 Configuration?

    Yes... In fact I just want the valve to be fully openned or fully closed. So, I just need a set value to fully open the valve after a defined period of time (eg. 3 sec.) and a set value to be sent (after that) to the valve controler to fully close it for a defined period of time (eg. 2 sec.). Regarding the valve controler it as to work with 0-10vdc and 4-20mA. (Please see page 4 of the pdf that I uploaded) Thank you... Best Regards, Adriano Pedro. MA1094_Standard_EU_ML.pdf
  4. Cpm1a - Mad01 Configuration?

    Hello, Actualy I don't have a Pressure value as an setpoint to be the Input. I have a Solenoid Valve that is controling the passage of gas from a CO2 bottle, and the pressure is set by the bottle manometer. So, I just need to open and close the valve in a defined time interval. Therefore I bought the PLC to make that control ( to open and close the valve) and the Analog I/O unit to make the interface between the PLC and the electronic part of the valve. That's why I don't have an Input... Thank you very much, Best Regards, Adriano Pedro
  5. Cpm1a - Mad01 Configuration?

    The problem is that I dont really know what would be an input in this case. I dont have any external device has an input. I just want the PLC to do that input in the Analog I/O Unit to be converted in an output that I can connect to the valve controler... Anyway I think the input range should be the same as the out put range (I dont know I I'm telling a by mustake!!! ) and the controler range works within 0-10V and 0/4-20mA... If it's not too much for you... could you send me an program example of what I should have for this case? Is it too complicated? Sorry for the inconvinience... Thank you very much for your help... Best Regards, Adriano Pedro
  6. Cpm1a - Mad01 Configuration?

    Hello, The PLC is a CPM1A-30CDR-A-V1. Is this enough? Regarding the W353 manual, I already have it and read the section 3 but.... ... sorry I need help... Thank you very much in advance, Adriano Pedro...
  7. Cpm1a - Mad01 Configuration?

    Dear all, I'm new in this field. Actualy I'm not even from this area... I'm a biologist and researcher. In order to develop a new application based on pressurized condition, I'm designing a device that could have a selenoid valve that would be controled by a PLC to open and close according to the defined parameters. Therefore, I bought a Selenoid valve Type 2822 from Burkert, with a Controler Type 1094 also from Burkert. To control all of this I also bought a CPM1A PLC and a Analog I/O (MAD01) to be possible to connect the valve controler. ALthough I new on this I managed to create a Program (the one available for download) that did work but for the outputs of the CPU... My great difculty is to set the Analog outputs in order to send the signal to the valve controler and control de valve... I know that its very likely an very easy work for some of you, but for a biologist!!!! Can some one help me doing this? Thank you very much in advance... Best Regards, Adriano Pedro. PS: the manual for the valve controler is also available for download(pdf) Prog020206.cxp MA1094_Standard_EU_ML.pdf