d4rkm4n
MrPLC Member-
Content count
54 -
Joined
-
Last visited
Community Reputation
2 NeutralAbout d4rkm4n
-
Rank
Sparky
Profile Information
- Gender
- Country Malaysia
-
d4rkm4n liked a post in a topic: Q-Series - Operation Error 4100
-
d4rkm4n liked a post in a topic: Q-Series - Operation Error 4100
-
I will try to disable the error once the process is stopp, btw, how do I permanently ON SM722? Is it back to OFF if I power cycle or restart the PLC. What do you think is the best way to debounce BCD value for weigher? I am afraid they are using the value to stop some sequence, I have not fully study the program yet due the writing looks so complex. =\
-
d4rkm4n liked a post in a topic: Q-Series - Operation Error 4100
-
Thanks for your input. I have checked the program and the input is coming from BCD signal from weigher. I found no abnormality on the weigher side. I also found as attached in the manual: The error will coming "When values other than 0 to 9 are specified to any digits of (S)", what will causing this? The input 10 will always give numeric right? Btw, also mentioned, error can be suppressed by turning ON SM722, if I turn ON the SM722, will the instruction still works? EDIT: Just checked, if abnormal inputs from BCD, the (S) will in minus (-). But as per picture, current (S) value is 0.
-
d4rkm4n liked a post in a topic: Q-Series - Operation Error 4100
-
d4rkm4n liked a post in a topic: GOT/GTDesigner3 Coordinates Error?
-
Sorry for bumping old thread. I still looking for solution.
-
Not really familiar with VFD but is whole module fail or just a point? Anything abnormal from 5 of those VFD? I think isolator is also a solution, your system been running fine for 10 years then not even with new module. Probably something on your VFD. Btw, I always wonder, what is the resistance reading indicate when we measure on intput/output terminal?
-
d4rkm4n liked a post in a topic: Analog output fail A1S
-
Digital Output. Is there any where I can study detail on this? I just confused how the whole, output can send 0V. Btw, I also wondering, how do I know the VDC value should I get at DO point when the signal is ON/OFF? As for DI already clear, need to check which one is connected to S/S.
-
Hi, sorry takes sometime to reply. Yes, our PLC was FX3U. So meaning the one connected to S/S will be common right? Is 24V is + and 0v is -? Btw, I found the output also act the same way, when DO is ON, it give 0V and 24V when OFF. Is it also based on S/S wiring? One thing I cannot understand, the DO give 0V when DO is ON but when we check contact at contactor (output receiver), it received 24V.
-
d4rkm4n liked a post in a topic: Loop Check for Digital Output
-
d4rkm4n liked a post in a topic: Contact Voltage?
-
You can download S7 Graph from Siemens website. Edit: Where do you procure the current trial software for SIMATIC S7-GRAPH V5.6? - ID: 109748125 - Industry Support Siemens
-
Hi guys, Currently I use MCR to disable program and create a M direct to Y, and online change for each Y It a bit slow for online change to completed. So, I wonder how to do loopcheck for let say 64 points DO? I try to make MOV M100 Y0 K4 but not success. Target to make M directly trigger a Y. Thanks!
-
Thanks. I thought the common can be separated as we have spare from A20 to A05. End up install interposing relay.
-
Hi guys. So I have a QY41P, currently signal is wet contact with 24VDC. I would like to use same module but with dry contact 0V, is it possible? I see there are 2 common termination provide but not sure how it was separate, from manual looks like it shared for all output. Thanks!
-
d4rkm4n liked a post in a topic: Q64AD Configuration
-
d4rkm4n liked a post in a topic: GT Simulator3 - Use PC keyboard to enter values - Found!
-
What is your input pulse interval? Normal condition, the input will always pulsing? If abnormal input no pulse? During actual test, does Y0 trigger?
-
Hi guys. During trobuleshooting one of our machines, I found that some DI modules give 24VDC when contact is OFF and 0VDC when contact is ON. Is there anywhere I can configure and change that setting? Thanks.
-
Did you able to read the GOT or do communication test?
-
Basically, you want a remote access to your PLC through internet? Try go search for MCWorks and MXConfigurator.